Home » Public Forums » GMCnet » Front Bearing Set question
Front Bearing Set question [message #87468] |
Sat, 05 June 2010 22:54 |
midlf
Messages: 2212 Registered: July 2007 Location: SE Wisc. (Palmyra)
Karma: 1
|
Senior Member |
|
|
Ray Erspamer came out today with his bearing tool to take my front hubs apart. It was a learning day as he has zerks on his GMC so he has never had to use his tool.
After getting the bearing cleaned up and reading the markings here is what I have:
LH outer bearing Bower Japan LO 104949E
LH outer race Timken USA LM104911 "6478"
LH inner bearing Timken USA LM104949E SY "6478-A"
LH inner race Timken USA LM104911 VY "6478-A"
LH spacer LM104911 ".006 6478"
RH outer bearing Timken USA LM104949E SY "6437-A"
RH outer race Timken USA LM104911 VY "6437-A
RH inner bearing Timken USA LM104949E SY "6437"
RH inner race Timken USA LM104911 VY "6437"
RH spacer ".006 6437"
(the numbers in "quotes" are hand etched)
The bearings and races pressed off with the expected force, good interference fits. No signs of wear, overheating, or damage on bearings, races, hubs or knuckles.
I have two concerns. The LH outer bearing does not appear to be part of the "6478" set. I'm not sure how the ".006" marked on the spacers relates to the .095 dimension I have seen referenced for these bearing sets.
Any comments or advice would be appreciated.
Steve Southworth
1974 Glacier TZE064V100150 (for workin on)
1975 Transmode TZE365V100394 (parts & spares)
Palmyra WI
|
|
|
Re: [GMCnet] Front Bearing Set question [message #87473 is a reply to message #87468] |
Sat, 05 June 2010 23:25 |
Charles
Messages: 455 Registered: January 2004
Karma: 0
|
Senior Member |
|
|
I would not go back with the left hand mismatched bearing.
I would go to Autozone and order a set 23 Timken and
replace it.
As for the right bearing I think the concess is any spacing
of .006 to .009 is acceptable. I would place the bearing
set in a vise and check the spacing. If it checks within the
.006 to .009 range and does not have any scratches or
gaulding, I would use it.
Charles
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Charles Wersal
Duncanville, Texas
26 foot 1975 Glenbrook
Pandora's Box
|
|
|
Re: [GMCnet] Front Bearing Set question [message #87477 is a reply to message #87468] |
Sun, 06 June 2010 00:13 |
|
USAussie
Messages: 15912 Registered: July 2007 Location: Sydney, Australia
Karma: 6
|
Senior Member |
|
|
Steve,
So it was the blind leading the blind eh? ;-) Not such a tough job after all
was it?
Maybe someone swapped a Bower bearing for the Timken in the LH outer
bearing?
I seem to remember someone posting that the bearings for a Toronado were
clearanced at 0.0060 and the bearings for a GMC were clearanced at 0.0095.
Keep in mind that I suffer from CRS and CRAFT!
I am happy to hear that everything "looks" OK, now all you have to do is
measure everything and make sure it's all within tolerance.
As far as the bearings go I would buy a new set and save the used ones for
spares. I would also get new inner and outer seals. Once you get the zerks
installed there's no reason to disassemble it ever again!
Regards,
Rob Mueller
Sydney, Australia
AUS '75 Avion-The Blue Streak TZE365V100428
USA '75 Avion-Double Trouble TZE365V100426
-----Original Message-----
From: Steve Southworth
The bearings and races pressed off with the expected force, good
interference fits. No signs of wear, overheating, or damage on bearings,
races, hubs or knuckles.
I have two concerns. The LH outer bearing does not appear to be part of the
"6478" set. I'm not sure how the ".006" marked on the spacers relates to
the .095 dimension I have seen referenced for these bearing sets.
Any comments or advice would be appreciated.
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Regards,
Rob M. (USAussie)
The Pedantic Mechanic
Sydney, Australia
'75 Avion - AUS - The Blue Streak TZE365V100428
'75 Avion - USA - Double Trouble TZE365V100426
|
|
|
|
Re: [GMCnet] Front Bearing Set question [message #87486 is a reply to message #87468] |
Sun, 06 June 2010 07:40 |
Ken Henderson
Messages: 8726 Registered: March 2004 Location: Americus, GA
Karma: 9
|
Senior Member |
|
|
Steve,
IMHO, you've been very lucky that those bearings have not failed; they were
very ineptly installed according to all I've read, heard, and experienced
over the past 12 years. To have mixed the components of different bearing
sets in that manner is unconscionable.
No doubt in my mind whatsoever that I'd install new Timken A23 sets, making
sure the spacers were engraved "0.0095". Any other choice is, IMHO, "penny
wise and pound foolish".
And don't forget that there are correct and incorrect inner seals being
marketed -- you've probably seen Larry Weidner's recent posting with photos;
if not, we'll find it.
Just get the correct bearings & seals from Dave Lenzi.
Ken H.
Americus, GA
'76 X-Birchaven
www.gmcwipersetc.com
On Sat, Jun 5, 2010 at 11:54 PM, Steve Southworth <midlf@centurytel.net>wrote:
>
> ...
After getting the bearing cleaned up and reading the markings here is what I
> have:
>
> LH outer bearing Bower Japan LO 104949E
> LH outer race Timken USA LM104911 "6478"
> LH inner bearing Timken USA LM104949E SY "6478-A"
> LH inner race Timken USA LM104911 VY "6478-A"
> LH spacer LM104911 ".006 6478"
>
> RH outer bearing Timken USA LM104949E SY "6437-A"
> RH outer race Timken USA LM104911 VY "6437-A
> RH inner bearing Timken USA LM104949E SY "6437"
> RH inner race Timken USA LM104911 VY "6437"
> RH spacer ".006 6437"
>
> (the numbers in "quotes" are hand etched)
>
> The bearings and races pressed off with the expected force, good
> interference fits. No signs of wear, overheating, or damage on bearings,
> races, hubs or knuckles.
>
>
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Ken Henderson
Americus, GA
www.gmcwipersetc.com
Large Wiring Diagrams
76 X-Birchaven
76 X-Palm Beach
|
|
|
Re: [GMCnet] Front Bearing Set question [message #87488 is a reply to message #87477] |
Sun, 06 June 2010 07:57 |
Ray Erspamer
Messages: 1707 Registered: May 2007 Location: Milwaukee Wisconsin
Karma: -3
|
Senior Member |
|
|
It was definitely the blind leading the blind, but we had a great fun time. Once we figured out that my Warner bearing tool was missing some key parts we started to understand things much better. I am definitely going to get the missing parts fab'd so I have the complete set, then I'm going to watch the Ken Toma video and make some modifications to my bearing tool so we can use air tools vs brute force with hand wrenches and a lot of grunting.
Steve, I would definitely replace that mismatched bearing set.
Ray
Ray & Lisa Erspamer
78 Royale Center Kitchen
TZE368V101144
Wauwatosa, Wisconsin 53226
Email: 78GMC-Royale@att.net
414-745-3188
Web Site: http://ray-lisa.page.tl/
________________________________
From: Rob Mueller <robmueller@iinet.net.au>
To: gmclist@temp.gmcnet.org
Sent: Sun, June 6, 2010 12:13:08 AM
Subject: Re: [GMCnet] Front Bearing Set question
Steve,
So it was the blind leading the blind eh? ;-) Not such a tough job after all
was it?
Maybe someone swapped a Bower bearing for the Timken in the LH outer
bearing?
I seem to remember someone posting that the bearings for a Toronado were
clearanced at 0.0060 and the bearings for a GMC were clearanced at 0.0095.
Keep in mind that I suffer from CRS and CRAFT!
I am happy to hear that everything "looks" OK, now all you have to do is
measure everything and make sure it's all within tolerance.
As far as the bearings go I would buy a new set and save the used ones for
spares. I would also get new inner and outer seals. Once you get the zerks
installed there's no reason to disassemble it ever again!
Regards,
Rob Mueller
Sydney, Australia
AUS '75 Avion-The Blue Streak TZE365V100428
USA '75 Avion-Double Trouble TZE365V100426
-----Original Message-----
From: Steve Southworth
The bearings and races pressed off with the expected force, good
interference fits. No signs of wear, overheating, or damage on bearings,
races, hubs or knuckles.
I have two concerns. The LH outer bearing does not appear to be part of the
"6478" set. I'm not sure how the ".006" marked on the spacers relates to
the .095 dimension I have seen referenced for these bearing sets.
Any comments or advice would be appreciated.
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Ray Erspamer
78 GMC Royale Center Kitchen
403, 3.70 Final Drive
Holley Sniper Quadrajet EFI System,
Holley Hyperspark Ignition System
414-484-9431
|
|
|
|
Re: [GMCnet] Front Bearing Set question [message #87492 is a reply to message #87491] |
Sun, 06 June 2010 08:22 |
Ray Erspamer
Messages: 1707 Registered: May 2007 Location: Milwaukee Wisconsin
Karma: -3
|
Senior Member |
|
|
Hi Gary, YES, that is the part I'm missing along with the screw that goes through it.
Can I buy it from you ??
Ray
Ray & Lisa Erspamer
78 Royale Center Kitchen
TZE368V101144
Wauwatosa, Wisconsin 53226
Email: 78GMC-Royale@att.net
414-745-3188
Web Site: http://ray-lisa.page.tl/
________________________________
From: Gary W. Mills <daveel@ix.netcom.com>
To: gmclist@temp.gmcnet.org
Sent: Sun, June 6, 2010 8:14:13 AM
Subject: Re: [GMCnet] Front Bearing Set question
Ray
I have some extra parts in my Warner bearing tool set. One of the extras is
the triangle plate with the holes in the corners. Would this be something
you would need?
Gary W. Mills (Livonia MI)
. ___________
./_][__][] []| 1974 GMC M/H
.*O-------OO-* Painted Desert
"Tangerine Dream" W/New Frame
-----Original Message-----
From: gmclist-bounces@temp.gmcnet.org
[mailto:gmclist-bounces@temp.gmcnet.org]On Behalf Of Ray Erspamer
Sent: Sunday, June 06, 2010 8:58 AM
To: gmclist@temp.gmcnet.org
Subject: Re: [GMCnet] Front Bearing Set question
It was definitely the blind leading the blind, but we had a great fun time.
Once we figured out that my Warner bearing tool was missing some key parts
we started to understand things much better. I am definitely going to get
the missing parts fab'd so I have the complete set, then I'm going to watch
the Ken Toma video and make some modifications to my bearing tool so we can
use air tools vs brute force with hand wrenches and a lot of grunting.
Steve, I would definitely replace that mismatched bearing set.
Ray
Ray & Lisa Erspamer
78 Royale Center Kitchen
TZE368V101144
Wauwatosa, Wisconsin 53226
Email: 78GMC-Royale@att.net
414-745-3188
Web Site: http://ray-lisa.page.tl/
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Ray Erspamer
78 GMC Royale Center Kitchen
403, 3.70 Final Drive
Holley Sniper Quadrajet EFI System,
Holley Hyperspark Ignition System
414-484-9431
|
|
|
Re: [GMCnet] Front Bearing Set question [message #87493 is a reply to message #87492] |
Sun, 06 June 2010 08:29 |
|
Tangerine
Messages: 192 Registered: February 2004 Location: Livonia, MI
Karma: 0
|
Senior Member |
|
|
Ray
I can sell you the triangle piece, but I only have one of the screws. What
would you be willing to pay for the plate? I can send it in the mail for
about $5.00.
Gary
-----Original Message-----
From: gmclist-bounces@temp.gmcnet.org
[mailto:gmclist-bounces@temp.gmcnet.org]On Behalf Of Ray Erspamer
Sent: Sunday, June 06, 2010 9:22 AM
To: gmclist@temp.gmcnet.org
Subject: Re: [GMCnet] Front Bearing Set question
Hi Gary, YES, that is the part I'm missing along with the screw that goes
through it.
Can I buy it from you ??
Ray
Ray & Lisa Erspamer
78 Royale Center Kitchen
TZE368V101144
Wauwatosa, Wisconsin 53226
Email: 78GMC-Royale@att.net
414-745-3188
Web Site: http://ray-lisa.page.tl/
________________________________
From: Gary W. Mills <daveel@ix.netcom.com>
To: gmclist@temp.gmcnet.org
Sent: Sun, June 6, 2010 8:14:13 AM
Subject: Re: [GMCnet] Front Bearing Set question
Ray
I have some extra parts in my Warner bearing tool set. One of the extras is
the triangle plate with the holes in the corners. Would this be something
you would need?
Gary W. Mills (Livonia MI)
. ___________
./_][__][] []| 1974 GMC M/H
.*O-------OO-* Painted Desert
"Tangerine Dream" W/New Frame
-----Original Message-----
From: gmclist-bounces@temp.gmcnet.org
[mailto:gmclist-bounces@temp.gmcnet.org]On Behalf Of Ray Erspamer
Sent: Sunday, June 06, 2010 8:58 AM
To: gmclist@temp.gmcnet.org
Subject: Re: [GMCnet] Front Bearing Set question
It was definitely the blind leading the blind, but we had a great fun time.
Once we figured out that my Warner bearing tool was missing some key parts
we started to understand things much better. I am definitely going to get
the missing parts fab'd so I have the complete set, then I'm going to watch
the Ken Toma video and make some modifications to my bearing tool so we can
use air tools vs brute force with hand wrenches and a lot of grunting.
Steve, I would definitely replace that mismatched bearing set.
Ray
Ray & Lisa Erspamer
78 Royale Center Kitchen
TZE368V101144
Wauwatosa, Wisconsin 53226
Email: 78GMC-Royale@att.net
414-745-3188
Web Site: http://ray-lisa.page.tl/
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
1974 GMC 260
Tangerine Dream
Livonia Michigan
|
|
|
Re: [GMCnet] Front Bearing Set question [message #87494 is a reply to message #87492] |
Sun, 06 June 2010 08:30 |
Mr ERFisher
Messages: 7117 Registered: August 2005
Karma: 2
|
Senior Member |
|
|
you might also think about making one of these for the warner puller
http://www.gmcmhphotos.com/photos/showphoto.php?photo=2007&cat=3195
gene
On Sun, Jun 6, 2010 at 6:22 AM, Ray Erspamer <78gmc-royale@att.net> wrote:
> Hi Gary, YES, that is the part I'm missing along with the screw that goes
> through it.
>
> Can I buy it from you ??
>
> Ray
>
>
> Ray & Lisa Erspamer
> 78 Royale Center Kitchen
> TZE368V101144
> Wauwatosa, Wisconsin 53226
> Email: 78GMC-Royale@att.net
> 414-745-3188
> Web Site: http://ray-lisa.page.tl/
>
>
>
>
> ________________________________
> From: Gary W. Mills <daveel@ix.netcom.com>
> To: gmclist@temp.gmcnet.org
> Sent: Sun, June 6, 2010 8:14:13 AM
> Subject: Re: [GMCnet] Front Bearing Set question
>
> Ray
> I have some extra parts in my Warner bearing tool set. One of the extras
> is
> the triangle plate with the holes in the corners. Would this be something
> you would need?
> Gary W. Mills (Livonia MI)
> . ___________
> ./_][__][] []| 1974 GMC M/H
> .*O-------OO-* Painted Desert
> "Tangerine Dream" W/New Frame
>
>
>
> -----Original Message-----
> From: gmclist-bounces@temp.gmcnet.org
> [mailto:gmclist-bounces@temp.gmcnet.org]On Behalf Of Ray Erspamer
> Sent: Sunday, June 06, 2010 8:58 AM
> To: gmclist@temp.gmcnet.org
> Subject: Re: [GMCnet] Front Bearing Set question
>
>
> It was definitely the blind leading the blind, but we had a great fun time.
> Once we figured out that my Warner bearing tool was missing some key parts
> we started to understand things much better. I am definitely going to get
> the missing parts fab'd so I have the complete set, then I'm going to watch
> the Ken Toma video and make some modifications to my bearing tool so we can
> use air tools vs brute force with hand wrenches and a lot of grunting.
>
> Steve, I would definitely replace that mismatched bearing set.
>
>
>
> Ray
>
>
> Ray & Lisa Erspamer
> 78 Royale Center Kitchen
> TZE368V101144
> Wauwatosa, Wisconsin 53226
> Email: 78GMC-Royale@att.net
> 414-745-3188
> Web Site: http://ray-lisa.page.tl/
>
>
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
--
Gene Fisher -- 74-23,77PB/ore/ca
“Give a man a fish; you have fed him for today --- give him a URL and
-------
http://gmcmotorhome.info/
Alternator Protection Cable
http://gmcmotorhome.info/APC.html
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
Re: [GMCnet] Front Bearing Set question [message #87495 is a reply to message #87492] |
Sun, 06 June 2010 08:40 |
Charles
Messages: 455 Registered: January 2004
Karma: 0
|
Senior Member |
|
|
Ray,
The triangle plate can use the same screw the rest of the unit uses.
If you do modify the Warner tool to use an impact be extra sure to
grease the screw heavily. The screw with the Warner tool is only about a
grade 5 and is subject to galling when impacted.
Charles
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Charles Wersal
Duncanville, Texas
26 foot 1975 Glenbrook
Pandora's Box
|
|
|
Re: [GMCnet] Front Bearing Set question [message #87496 is a reply to message #87494] |
Sun, 06 June 2010 08:43 |
Mr ERFisher
Messages: 7117 Registered: August 2005
Karma: 2
|
Senior Member |
|
|
and a fairly complete look at the Warner kit
(sorry - I lost the name of who took this picture)
http://www.gmcmhphotos.com/photos/showphoto.php?photo=34270&title=warner&cat=3195
gene
On Sun, Jun 6, 2010 at 6:30 AM, Mr.erf ERFisher <mr.erfisher@gmail.com>wrote:
> you might also think about making one of these for the warner puller
>
> http://www.gmcmhphotos.com/photos/showphoto.php?photo=2007&cat=3195
>
> gene
>
>
>
>
> On Sun, Jun 6, 2010 at 6:22 AM, Ray Erspamer <78gmc-royale@att.net> wrote:
>
>> Hi Gary, YES, that is the part I'm missing along with the screw that
>> goes through it.
>>
>> Can I buy it from you ??
>>
>> Ray
>>
>>
>> Ray & Lisa Erspamer
>> 78 Royale Center Kitchen
>> TZE368V101144
>> Wauwatosa, Wisconsin 53226
>> Email: 78GMC-Royale@att.net
>> 414-745-3188
>> Web Site: http://ray-lisa.page.tl/
>>
>>
>>
>>
>> ________________________________
>> From: Gary W. Mills <daveel@ix.netcom.com>
>> To: gmclist@temp.gmcnet.org
>> Sent: Sun, June 6, 2010 8:14:13 AM
>> Subject: Re: [GMCnet] Front Bearing Set question
>>
>> Ray
>> I have some extra parts in my Warner bearing tool set. One of the extras
>> is
>> the triangle plate with the holes in the corners. Would this be something
>> you would need?
>> Gary W. Mills (Livonia MI)
>> . ___________
>> ./_][__][] []| 1974 GMC M/H
>> .*O-------OO-* Painted Desert
>> "Tangerine Dream" W/New Frame
>>
>>
>>
>> -----Original Message-----
>> From: gmclist-bounces@temp.gmcnet.org
>> [mailto:gmclist-bounces@temp.gmcnet.org]On Behalf Of Ray Erspamer
>> Sent: Sunday, June 06, 2010 8:58 AM
>> To: gmclist@temp.gmcnet.org
>> Subject: Re: [GMCnet] Front Bearing Set question
>>
>>
>> It was definitely the blind leading the blind, but we had a great fun
>> time.
>> Once we figured out that my Warner bearing tool was missing some key parts
>> we started to understand things much better. I am definitely going to get
>> the missing parts fab'd so I have the complete set, then I'm going to
>> watch
>> the Ken Toma video and make some modifications to my bearing tool so we
>> can
>> use air tools vs brute force with hand wrenches and a lot of grunting.
>>
>> Steve, I would definitely replace that mismatched bearing set.
>>
>>
>>
>> Ray
>>
>>
>> Ray & Lisa Erspamer
>> 78 Royale Center Kitchen
>> TZE368V101144
>> Wauwatosa, Wisconsin 53226
>> Email: 78GMC-Royale@att.net
>> 414-745-3188
>> Web Site: http://ray-lisa.page.tl/
>>
>>
>> _______________________________________________
>> GMCnet mailing list
>> List Information and Subscription Options:
>> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>> _______________________________________________
>> GMCnet mailing list
>> List Information and Subscription Options:
>> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>>
>
>
>
> --
> Gene Fisher -- 74-23,77PB/ore/ca
> “Give a man a fish; you have fed him for today --- give him a URL and
> -------
> http://gmcmotorhome.info/
> Alternator Protection Cable
> http://gmcmotorhome.info/APC.html
>
--
Gene Fisher -- 74-23,77PB/ore/ca
“Give a man a fish; you have fed him for today --- give him a URL and
-------
http://gmcmotorhome.info/
Alternator Protection Cable
http://gmcmotorhome.info/APC.html
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
Re: [GMCnet] Front Bearing Set question [message #87498 is a reply to message #87496] |
Sun, 06 June 2010 09:00 |
Ray Erspamer
Messages: 1707 Registered: May 2007 Location: Milwaukee Wisconsin
Karma: -3
|
Senior Member |
|
|
In looking at this KIT picture, I'm missing LOTS of parts ! Lucky I work at a manufacturing company and have access to getting some of this made.
Ray
Ray & Lisa Erspamer
78 Royale Center Kitchen
TZE368V101144
Wauwatosa, Wisconsin 53226
Email: 78GMC-Royale@att.net
414-745-3188
Web Site: http://ray-lisa.page.tl/
________________________________
From: Mr.erf ERFisher <mr.erfisher@gmail.com>
To: gmclist@temp.gmcnet.org
Sent: Sun, June 6, 2010 8:43:43 AM
Subject: Re: [GMCnet] Front Bearing Set question
and a fairly complete look at the Warner kit
(sorry - I lost the name of who took this picture)
http://www.gmcmhphotos.com/photos/showphoto.php?photo=34270&title=warner&cat=3195
gene
On Sun, Jun 6, 2010 at 6:30 AM, Mr.erf ERFisher <mr.erfisher@gmail.com>wrote:
> you might also think about making one of these for the warner puller
>
> http://www.gmcmhphotos.com/photos/showphoto.php?photo=2007&cat=3195
>
> gene
>
>
>
>
> On Sun, Jun 6, 2010 at 6:22 AM, Ray Erspamer <78gmc-royale@att.net> wrote:
>
>> Hi Gary, YES, that is the part I'm missing along with the screw that
>> goes through it.
>>
>> Can I buy it from you ??
>>
>> Ray
>>
>>
>> Ray & Lisa Erspamer
>> 78 Royale Center Kitchen
>> TZE368V101144
>> Wauwatosa, Wisconsin 53226
>> Email: 78GMC-Royale@att.net
>> 414-745-3188
>> Web Site: http://ray-lisa.page.tl/
>>
>>
>>
>>
>> ________________________________
>> From: Gary W. Mills <daveel@ix.netcom.com>
>> To: gmclist@temp.gmcnet.org
>> Sent: Sun, June 6, 2010 8:14:13 AM
>> Subject: Re: [GMCnet] Front Bearing Set question
>>
>> Ray
>> I have some extra parts in my Warner bearing tool set. One of the extras
>> is
>> the triangle plate with the holes in the corners. Would this be something
>> you would need?
>> Gary W. Mills (Livonia MI)
>> . ___________
>> ./_][__][] []| 1974 GMC M/H
>> .*O-------OO-* Painted Desert
>> "Tangerine Dream" W/New Frame
>>
>>
>>
>> -----Original Message-----
>> From: gmclist-bounces@temp.gmcnet.org
>> [mailto:gmclist-bounces@temp.gmcnet.org]On Behalf Of Ray Erspamer
>> Sent: Sunday, June 06, 2010 8:58 AM
>> To: gmclist@temp.gmcnet.org
>> Subject: Re: [GMCnet] Front Bearing Set question
>>
>>
>> It was definitely the blind leading the blind, but we had a great fun
>> time.
>> Once we figured out that my Warner bearing tool was missing some key parts
>> we started to understand things much better. I am definitely going to get
>> the missing parts fab'd so I have the complete set, then I'm going to
>> watch
>> the Ken Toma video and make some modifications to my bearing tool so we
>> can
>> use air tools vs brute force with hand wrenches and a lot of grunting.
>>
>> Steve, I would definitely replace that mismatched bearing set.
>>
>>
>>
>> Ray
>>
>>
>> Ray & Lisa Erspamer
>> 78 Royale Center Kitchen
>> TZE368V101144
>> Wauwatosa, Wisconsin 53226
>> Email: 78GMC-Royale@att.net
>> 414-745-3188
>> Web Site: http://ray-lisa.page.tl/
>>
>>
>> _______________________________________________
>> GMCnet mailing list
>> List Information and Subscription Options:
>> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>> _______________________________________________
>> GMCnet mailing list
>> List Information and Subscription Options:
>> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>>
>
>
>
> --
> Gene Fisher -- 74-23,77PB/ore/ca
> “Give a man a fish; you have fed him for today --- give him a URL and
> -------
> http://gmcmotorhome.info/
> Alternator Protection Cable
> http://gmcmotorhome.info/APC.html
>
--
Gene Fisher -- 74-23,77PB/ore/ca
“Give a man a fish; you have fed him for today --- give him a URL and
-------
http://gmcmotorhome.info/
Alternator Protection Cable
http://gmcmotorhome.info/APC.html
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Ray Erspamer
78 GMC Royale Center Kitchen
403, 3.70 Final Drive
Holley Sniper Quadrajet EFI System,
Holley Hyperspark Ignition System
414-484-9431
|
|
|
Re: [GMCnet] Front Bearing Set question [message #87499 is a reply to message #87493] |
Sun, 06 June 2010 09:01 |
Ray Erspamer
Messages: 1707 Registered: May 2007 Location: Milwaukee Wisconsin
Karma: -3
|
Senior Member |
|
|
Gary, I have no idea what it's worth, just shoot me a price. I had planned on just making one, but this would be much easier.
Ray
Ray & Lisa Erspamer
78 Royale Center Kitchen
TZE368V101144
Wauwatosa, Wisconsin 53226
Email: 78GMC-Royale@att.net
414-745-3188
Web Site: http://ray-lisa.page.tl/
________________________________
From: Gary W. Mills <daveel@ix.netcom.com>
To: gmclist@temp.gmcnet.org
Sent: Sun, June 6, 2010 8:29:39 AM
Subject: Re: [GMCnet] Front Bearing Set question
Ray
I can sell you the triangle piece, but I only have one of the screws. What
would you be willing to pay for the plate? I can send it in the mail for
about $5.00.
Gary
-----Original Message-----
From: gmclist-bounces@temp.gmcnet.org
[mailto:gmclist-bounces@temp.gmcnet.org]On Behalf Of Ray Erspamer
Sent: Sunday, June 06, 2010 9:22 AM
To: gmclist@temp.gmcnet.org
Subject: Re: [GMCnet] Front Bearing Set question
Hi Gary, YES, that is the part I'm missing along with the screw that goes
through it.
Can I buy it from you ??
Ray
Ray & Lisa Erspamer
78 Royale Center Kitchen
TZE368V101144
Wauwatosa, Wisconsin 53226
Email: 78GMC-Royale@att.net
414-745-3188
Web Site: http://ray-lisa.page.tl/
________________________________
From: Gary W. Mills <daveel@ix.netcom.com>
To: gmclist@temp.gmcnet.org
Sent: Sun, June 6, 2010 8:14:13 AM
Subject: Re: [GMCnet] Front Bearing Set question
Ray
I have some extra parts in my Warner bearing tool set. One of the extras is
the triangle plate with the holes in the corners. Would this be something
you would need?
Gary W. Mills (Livonia MI)
. ___________
./_][__][] []| 1974 GMC M/H
.*O-------OO-* Painted Desert
"Tangerine Dream" W/New Frame
-----Original Message-----
From: gmclist-bounces@temp.gmcnet.org
[mailto:gmclist-bounces@temp.gmcnet.org]On Behalf Of Ray Erspamer
Sent: Sunday, June 06, 2010 8:58 AM
To: gmclist@temp.gmcnet.org
Subject: Re: [GMCnet] Front Bearing Set question
It was definitely the blind leading the blind, but we had a great fun time.
Once we figured out that my Warner bearing tool was missing some key parts
we started to understand things much better. I am definitely going to get
the missing parts fab'd so I have the complete set, then I'm going to watch
the Ken Toma video and make some modifications to my bearing tool so we can
use air tools vs brute force with hand wrenches and a lot of grunting.
Steve, I would definitely replace that mismatched bearing set.
Ray
Ray & Lisa Erspamer
78 Royale Center Kitchen
TZE368V101144
Wauwatosa, Wisconsin 53226
Email: 78GMC-Royale@att.net
414-745-3188
Web Site: http://ray-lisa.page.tl/
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Ray Erspamer
78 GMC Royale Center Kitchen
403, 3.70 Final Drive
Holley Sniper Quadrajet EFI System,
Holley Hyperspark Ignition System
414-484-9431
|
|
|
Re: [GMCnet] Front Bearing Set question [message #87500 is a reply to message #87494] |
Sun, 06 June 2010 09:02 |
Ray Erspamer
Messages: 1707 Registered: May 2007 Location: Milwaukee Wisconsin
Karma: -3
|
Senior Member |
|
|
So what exactly is this option for Gene, I'm still trying to figure all of this out.
Ray
Ray & Lisa Erspamer
78 Royale Center Kitchen
TZE368V101144
Wauwatosa, Wisconsin 53226
Email: 78GMC-Royale@att.net
414-745-3188
Web Site: http://ray-lisa.page.tl/
________________________________
From: Mr.erf ERFisher <mr.erfisher@gmail.com>
To: gmclist@temp.gmcnet.org
Sent: Sun, June 6, 2010 8:30:34 AM
Subject: Re: [GMCnet] Front Bearing Set question
you might also think about making one of these for the warner puller
http://www.gmcmhphotos.com/photos/showphoto.php?photo=2007&cat=3195
gene
On Sun, Jun 6, 2010 at 6:22 AM, Ray Erspamer <78gmc-royale@att.net> wrote:
> Hi Gary, YES, that is the part I'm missing along with the screw that goes
> through it.
>
> Can I buy it from you ??
>
> Ray
>
>
> Ray & Lisa Erspamer
> 78 Royale Center Kitchen
> TZE368V101144
> Wauwatosa, Wisconsin 53226
> Email: 78GMC-Royale@att.net
> 414-745-3188
> Web Site: http://ray-lisa.page.tl/
>
>
>
>
> ________________________________
> From: Gary W. Mills <daveel@ix.netcom.com>
> To: gmclist@temp.gmcnet.org
> Sent: Sun, June 6, 2010 8:14:13 AM
> Subject: Re: [GMCnet] Front Bearing Set question
>
> Ray
> I have some extra parts in my Warner bearing tool set. One of the extras
> is
> the triangle plate with the holes in the corners. Would this be something
> you would need?
> Gary W. Mills (Livonia MI)
> . ___________
> ./_][__][] []| 1974 GMC M/H
> .*O-------OO-* Painted Desert
> "Tangerine Dream" W/New Frame
>
>
>
> -----Original Message-----
> From: gmclist-bounces@temp.gmcnet.org
> [mailto:gmclist-bounces@temp.gmcnet.org]On Behalf Of Ray Erspamer
> Sent: Sunday, June 06, 2010 8:58 AM
> To: gmclist@temp.gmcnet.org
> Subject: Re: [GMCnet] Front Bearing Set question
>
>
> It was definitely the blind leading the blind, but we had a great fun time.
> Once we figured out that my Warner bearing tool was missing some key parts
> we started to understand things much better. I am definitely going to get
> the missing parts fab'd so I have the complete set, then I'm going to watch
> the Ken Toma video and make some modifications to my bearing tool so we can
> use air tools vs brute force with hand wrenches and a lot of grunting.
>
> Steve, I would definitely replace that mismatched bearing set.
>
>
>
> Ray
>
>
> Ray & Lisa Erspamer
> 78 Royale Center Kitchen
> TZE368V101144
> Wauwatosa, Wisconsin 53226
> Email: 78GMC-Royale@att.net
> 414-745-3188
> Web Site: http://ray-lisa.page.tl/
>
>
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
--
Gene Fisher -- 74-23,77PB/ore/ca
“Give a man a fish; you have fed him for today --- give him a URL and
-------
http://gmcmotorhome.info/
Alternator Protection Cable
http://gmcmotorhome.info/APC.html
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Ray Erspamer
78 GMC Royale Center Kitchen
403, 3.70 Final Drive
Holley Sniper Quadrajet EFI System,
Holley Hyperspark Ignition System
414-484-9431
|
|
|
Re: [GMCnet] Front Bearing Set question [message #87502 is a reply to message #87500] |
Sun, 06 June 2010 09:10 |
Mr ERFisher
Messages: 7117 Registered: August 2005
Karma: 2
|
Senior Member |
|
|
hold the clamp while you use impact wrench
gene
On Sun, Jun 6, 2010 at 7:02 AM, Ray Erspamer <78gmc-royale@att.net> wrote:
> So what exactly is this option for Gene, I'm still trying to figure all of
> this out.
>
> Ray
>
>
> Ray & Lisa Erspamer
> 78 Royale Center Kitchen
> TZE368V101144
> Wauwatosa, Wisconsin 53226
> Email: 78GMC-Royale@att.net
> 414-745-3188
> Web Site: http://ray-lisa.page.tl/
>
>
>
>
> ________________________________
> From: Mr.erf ERFisher <mr.erfisher@gmail.com>
> To: gmclist@temp.gmcnet.org
> Sent: Sun, June 6, 2010 8:30:34 AM
> Subject: Re: [GMCnet] Front Bearing Set question
>
> you might also think about making one of these for the warner puller
>
> http://www.gmcmhphotos.com/photos/showphoto.php?photo=2007&cat=3195
>
> gene
>
>
>
> On Sun, Jun 6, 2010 at 6:22 AM, Ray Erspamer <78gmc-royale@att.net> wrote:
>
> > Hi Gary, YES, that is the part I'm missing along with the screw that
> goes
> > through it.
> >
> > Can I buy it from you ??
> >
> > Ray
> >
> >
> > Ray & Lisa Erspamer
> > 78 Royale Center Kitchen
> > TZE368V101144
> > Wauwatosa, Wisconsin 53226
> > Email: 78GMC-Royale@att.net
> > 414-745-3188
> > Web Site: http://ray-lisa.page.tl/
> >
> >
> >
> >
> > ________________________________
> > From: Gary W. Mills <daveel@ix.netcom.com>
> > To: gmclist@temp.gmcnet.org
> > Sent: Sun, June 6, 2010 8:14:13 AM
> > Subject: Re: [GMCnet] Front Bearing Set question
> >
> > Ray
> > I have some extra parts in my Warner bearing tool set. One of the extras
> > is
> > the triangle plate with the holes in the corners. Would this be
> something
> > you would need?
> > Gary W. Mills (Livonia MI)
> > . ___________
> > ./_][__][] []| 1974 GMC M/H
> > .*O-------OO-* Painted Desert
> > "Tangerine Dream" W/New Frame
> >
> >
> >
> > -----Original Message-----
> > From: gmclist-bounces@temp.gmcnet.org
> > [mailto:gmclist-bounces@temp.gmcnet.org]On Behalf Of Ray Erspamer
> > Sent: Sunday, June 06, 2010 8:58 AM
> > To: gmclist@temp.gmcnet.org
> > Subject: Re: [GMCnet] Front Bearing Set question
> >
> >
> > It was definitely the blind leading the blind, but we had a great fun
> time.
> > Once we figured out that my Warner bearing tool was missing some key
> parts
> > we started to understand things much better. I am definitely going to
> get
> > the missing parts fab'd so I have the complete set, then I'm going to
> watch
> > the Ken Toma video and make some modifications to my bearing tool so we
> can
> > use air tools vs brute force with hand wrenches and a lot of grunting.
> >
> > Steve, I would definitely replace that mismatched bearing set.
> >
> >
> >
> > Ray
> >
> >
> > Ray & Lisa Erspamer
> > 78 Royale Center Kitchen
> > TZE368V101144
> > Wauwatosa, Wisconsin 53226
> > Email: 78GMC-Royale@att.net
> > 414-745-3188
> > Web Site: http://ray-lisa.page.tl/
> >
> >
> > _______________________________________________
> > GMCnet mailing list
> > List Information and Subscription Options:
> > http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
> > _______________________________________________
> > GMCnet mailing list
> > List Information and Subscription Options:
> > http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
> >
>
>
>
> --
> Gene Fisher -- 74-23,77PB/ore/ca
> “Give a man a fish; you have fed him for today --- give him a URL and
> -------
> http://gmcmotorhome.info/
> Alternator Protection Cable
> http://gmcmotorhome.info/APC.html
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
--
Gene Fisher -- 74-23,77PB/ore/ca
“Give a man a fish; you have fed him for today --- give him a URL and
-------
http://gmcmotorhome.info/
Alternator Protection Cable
http://gmcmotorhome.info/APC.html
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
|
|
|
Goto Forum:
Current Time: Fri Oct 11 19:26:51 CDT 2024
Total time taken to generate the page: 0.01514 seconds
|