GMCforum
For enthusiast of the Classic GMC Motorhome built from 1973 to 1978. A web-based mirror of the GMCnet mailing list.
Home » Public Forums » GMCnet » 12 Ton Jack-Stands (or "How I keep from getting crushed")
12 Ton Jack-Stands [message #83103] Tue, 04 May 2010 23:04 Go to previous message
midlf is currently offline  midlf   United States
Messages: 2212
Registered: July 2007
Location: SE Wisc. (Palmyra)
Karma:
Senior Member
Peter Bailey of OZ wrote in another thread:

"Steve Southworth,
Tried to find you on the members list but couldn't, I wanted to send an off
net message as I felt that I would be hi jacking your original post but I
now have to , I want more information on making jack stands as you have
shown as I don't like the metal stands that I currently use< i fear one day
they will release and down the coach will come, like you if I have a wheel
off it goes under the frame in case of.
Are the timbers actually 4 inches x 2 inches or is that a termination of
something close, meaning the base is approx 20 inches square and the overall
stand is about 22 inches high?
how far in from the edge is each corresponding level?
Held together with what (glued with dowels, screws or nails)?
Regards Peter Bailey"

Well I figure the best way to do this is with a photo album (thanks bdub). See here:

http://www.gmcmhphotos.com/photos/showgallery.php?cat=5461


Background - I had a car, my Corvette, fall off jack-stands once. Fortunately I was not under it at the time as it would have been uncomfortable, but not fatal as I always put the removed tires under the frame. The part I do not like about conventional jack-stands is the metal pad on the top. That pad has no traction on the frame. I see many photos here of GMC's supported on two jack-stands with a slope on the frame. I feel this is just asking for the jack-stand to squirt out because that is exactly what happened to me with my Vette. Another part I am not comfortable with is the relatively small area of the base, especially compared to the height. After my incident I gave some thought to a better jack stand. I came up with a design using 2X4's that was extremely strong, proven by a trip to my 12 Ton shop press, had a wide base, could be made any height, had a wood top that will grab whatever is being supported, and as an added benefit, is very economical, it even can be called cheap (a set of 4 is less than $20 or so). It can be made any height. The only disadvantages is they are not adjustable (more around this in the photo album), and they take up a lot of room to store although they do sorta stack.


Peter - you will find me listed as midlf on the GMCforum and the photo album. That's my email address. I've found if I'm looking for someone to also check for them that way.

Steve Southworth
1974 Glacier TZE064V100150 (for workin on)
1975 Transmode TZE365V100394 (parts & spares)
Palmyra WI

Report message to a moderator

[Message index]
 
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Read Message
Previous Topic: [GMCnet] Prigmore didn't get to Calhoun rally, here's why
Next Topic: [GMCnet] ONAN IGNITION
Goto Forum:
  


Current Time: Sat Nov 16 19:34:54 CST 2024

Total time taken to generate the page: 0.01105 seconds
.:: Contact :: Home ::.

Powered by: FUDforum 3.1.1.
Copyright ©2001-2021 FUDforum Bulletin Board Software