Home » Public Forums » GMCnet » 12 Ton Jack-Stands (or "How I keep from getting crushed")
| 12 Ton Jack-Stands [message #83103] |
Tue, 04 May 2010 23:04  |
midlf
Messages: 2212
Registered: July 2007
Location: SE Wisc. (Palmyra)
Karma: 1
|
Senior Member |
|
|
Peter Bailey of OZ wrote in another thread:
"Steve Southworth,
Tried to find you on the members list but couldn't, I wanted to send an off
net message as I felt that I would be hi jacking your original post but I
now have to , I want more information on making jack stands as you have
shown as I don't like the metal stands that I currently use< i fear one day
they will release and down the coach will come, like you if I have a wheel
off it goes under the frame in case of.
Are the timbers actually 4 inches x 2 inches or is that a termination of
something close, meaning the base is approx 20 inches square and the overall
stand is about 22 inches high?
how far in from the edge is each corresponding level?
Held together with what (glued with dowels, screws or nails)?
Regards Peter Bailey"
Well I figure the best way to do this is with a photo album (thanks bdub). See here:
http://www.gmcmhphotos.com/photos/showgallery.php?cat=5461
Background - I had a car, my Corvette, fall off jack-stands once. Fortunately I was not under it at the time as it would have been uncomfortable, but not fatal as I always put the removed tires under the frame. The part I do not like about conventional jack-stands is the metal pad on the top. That pad has no traction on the frame. I see many photos here of GMC's supported on two jack-stands with a slope on the frame. I feel this is just asking for the jack-stand to squirt out because that is exactly what happened to me with my Vette. Another part I am not comfortable with is the relatively small area of the base, especially compared to the height. After my incident I gave some thought to a better jack stand. I came up with a design using 2X4's that was extremely strong, proven by a trip to my 12 Ton shop press, had a wide base, could be made any height, had a wood top that will grab whatever is being supported, and as an added benefit, is very economical, it even can be called cheap (a set of 4 is less than $20 or so). It can be made any height. The only disadvantages is they are not adjustable (more around this in the photo album), and they take up a lot of room to store although they do sorta stack.
Peter - you will find me listed as midlf on the GMCforum and the photo album. That's my email address. I've found if I'm looking for someone to also check for them that way.
Steve Southworth
1974 Glacier TZE064V100150 (for workin on)
1975 Transmode TZE365V100394 (parts & spares)
Palmyra WI
|
|
|
|
| Re: [GMCnet] 12 Ton Jack-Stands [message #83105 is a reply to message #83103] |
Tue, 04 May 2010 23:34  |
peter bailey
Messages: 367
Registered: March 2009
Location: Gawler, South Australia
Karma: 0
|
Senior Member |
|
|
Steve,
Thanks for information provided and I can see from your photos the simplest
way to build this is to start with the level that has two pieces together
( at a pre determined length) and with each level being an 1" longer and so
on and the ends level on one side with the corresponding piece of the level
underneath sides thus creating a strong construction (like brick laying) and
that governs the gap size between timbers for each level. When viewing from
any side every other level has the timber end pieces showing. to add to
height each level increases the base width.
Have to make sure they are stored to avoid termite damage or probably make
them from treated timber, that's how bad white ants are in our area.
I was looking through some of your postings for a clue to a username but
could not find one, and I was correct in my thinking as you have now
supplied that. Ta !
Peter Bailey
from Ozy (Aussie)
----- Original Message -----
From: "Steve Southworth" <midlf@centurytel.net>
To: <gmclist@temp.gmcnet.org>
Sent: Wednesday, May 05, 2010 1:34 PM
Subject: [GMCnet] 12 Ton Jack-Stands
>
>
> Peter Bailey of OZ wrote in another thread:
>
> "Steve Southworth,
> Tried to find you on the members list but couldn't, I wanted to send an
> off
> net message as I felt that I would be hi jacking your original post but I
> now have to , I want more information on making jack stands as you have
> shown as I don't like the metal stands that I currently use< i fear one
> day
> they will release and down the coach will come, like you if I have a wheel
> off it goes under the frame in case of.
> Are the timbers actually 4 inches x 2 inches or is that a termination of
> something close, meaning the base is approx 20 inches square and the
> overall
> stand is about 22 inches high?
> how far in from the edge is each corresponding level?
> Held together with what (glued with dowels, screws or nails)?
> Regards Peter Bailey"
>
> Well I figure the best way to do this is with a photo album (thanks bdub).
> See here:
>
> http://www.gmcmhphotos.com/photos/showgallery.php?cat=5461
>
>
> Background - I had a car, my Corvette, fall off jack-stands once.
> Fortunately I was not under it at the time as it would have been
> uncomfortable, but not fatal as I always put the removed tires under the
> frame. The part I do not like about conventional jack-stands is the metal
> pad on the top. That pad has no traction on the frame. I see many photos
> here of GMC's supported on two jack-stands with a slope on the frame. I
> feel this is just asking for the jack-stand to squirt out because that is
> exactly what happened to me with my Vette. Another part I am not
> comfortable with is the relatively small area of the base, especially
> compared to the height. After my incident I gave some thought to a better
> jack stand. I came up with a design using 2X4's that was extremely
> strong, proven by a trip to my 12 Ton shop press, had a wide base, could
> be made any height, had a wood top that will grab whatever is being
> supported, and as an added benefit, is very economical, it even can
> be called cheap (a set of 4 is less than $20 or so). It can be made any
> height. The only disadvantages is they are not adjustable (more around
> this in the photo album), and they take up a lot of room to store although
> they do sorta stack.
>
>
> Peter - you will find me listed as midlf on the GMCforum and the photo
> album. That's my email address. I've found if I'm looking for someone to
> also check for them that way.
> --
> Steve Southworth
> 1974 Glacier TZE064V100150
> Palmyra WI
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
| Re: 12 Ton Jack-Stands [message #83106 is a reply to message #83103] |
Tue, 04 May 2010 23:40 |
midlf
Messages: 2212
Registered: July 2007
Location: SE Wisc. (Palmyra)
Karma: 1
|
Senior Member |
|
|
Peter - The easiest way to build them is to start from the bottom with the longest pieces, space the next ones one inch in from each side, glue and nail them and repeat. If you do it "upside down" you will not have a firm backing for nailing. I use a carpenters square to make sure I am on track as I go. The alignment of the lowest level is critical, after that it just sorta flows up.
Steve Southworth
1974 Glacier TZE064V100150 (for workin on)
1975 Transmode TZE365V100394 (parts & spares)
Palmyra WI
|
|
|
|
| Re: [GMCnet] 12 Ton Jack-Stands [message #83109 is a reply to message #83105] |
Tue, 04 May 2010 23:49 |
midlf
Messages: 2212
Registered: July 2007
Location: SE Wisc. (Palmyra)
Karma: 1
|
Senior Member |
|
|
| Peter Bailey wrote on Tue, 04 May 2010 23:34 |
Steve,
Have to make sure they are stored to avoid termite damage or probably make
them from treated timber, that's how bad white ants are in our area.
I was looking through some of your postings for a clue to a username but
could not find one, and I was correct in my thinking as you have now
supplied that. Ta !
Peter Bailey
from Ozy (Aussie)
|
I'd go with treated, just have to wear the respirator while cutting and gloves while assembling. When I make a set for the transmode parts coach they will be treated 2X4's with a treated 3/4" plywood base or I may use some 2"x8"x4' treated planks under the jack-stand. The enhanced base will be to prevent it from sinking into the swamp muck we have for soil around the barn.
For the user name it is in the heading on the forum or as the email address on GMCnet.
Steve Southworth
1974 Glacier TZE064V100150 (for workin on)
1975 Transmode TZE365V100394 (parts & spares)
Palmyra WI
|
|
|
|
|
|
| Re: [GMCnet] 12 Ton Jack-Stands [message #83137 is a reply to message #83110] |
Wed, 05 May 2010 09:02 |
midlf
Messages: 2212
Registered: July 2007
Location: SE Wisc. (Palmyra)
Karma: 1
|
Senior Member |
|
|
The CFO reminded me that she had taken a lot of pictures of the process of building these jack-stands the last time I made some. I'll get those put in the album later today.
Steve Southworth
1974 Glacier TZE064V100150 (for workin on)
1975 Transmode TZE365V100394 (parts & spares)
Palmyra WI
|
|
|
|
| Re: [GMCnet] 12 Ton Jack-Stands [message #83140 is a reply to message #83110] |
Wed, 05 May 2010 09:18 |
midlf
Messages: 2212
Registered: July 2007
Location: SE Wisc. (Palmyra)
Karma: 1
|
Senior Member |
|
|
| Peter Bailey wrote on Wed, 05 May 2010 00:19 |
Steve,
So if one would require it taller then the
base would have to be larger as I said so the height one would require would
have to be determined before you start building.
Peter Bailey
from Ozy (Aussie)
|
Well I think there is a reasonable limit to the max base size needed. At 16" the base is large but not too intrusive into the work space under the vehicle. I had kind of decided that 16" was as big as I needed if I was going to go higher with the limit being 6" or 8" higher. Of course using a floor jack there is a limit as to how high you can go.
However to answer your question, yes you have to know how high you are going to determine the base size and thus you have to know that before you start. You could add on a layer later I suppose as it is not impossible. See my pictures for how I added a few inches with blocking. I feel that I can safely add 4 or so inches using blocking as shown. With a GMC's very flat frame and 1 ton on the jack-stand the blocking isn't going to move any.
Steve Southworth
1974 Glacier TZE064V100150 (for workin on)
1975 Transmode TZE365V100394 (parts & spares)
Palmyra WI
|
|
|
|
| Re: [GMCnet] 12 Ton Jack-Stands [message #83141 is a reply to message #83140] |
Wed, 05 May 2010 09:23 |
midlf
Messages: 2212
Registered: July 2007
Location: SE Wisc. (Palmyra)
Karma: 1
|
Senior Member |
|
|
| Gary Cottingame wrote on Wed, 05 May 2010 08:58 |
Steve,
Great design! I think I'll build some for my coach. I've been wondering what I could use on this soft soil I have around here.
Peter,Once you have built to Steve's design, you could always add height to the bottom, using screws and glue. Just keep on going up as high as you need. It seems that the more base you add, the more stability you have. You just create a larger footprint. [Right Steve?]
Gary
|
Right - I think the reply to one of Peter's posts has the full answer to this question.
Steve Southworth
1974 Glacier TZE064V100150 (for workin on)
1975 Transmode TZE365V100394 (parts & spares)
Palmyra WI
|
|
|
|
|
|
| Re: [GMCnet] 12 Ton Jack-Stands [message #83187 is a reply to message #83149] |
Wed, 05 May 2010 13:39 |
midlf
Messages: 2212
Registered: July 2007
Location: SE Wisc. (Palmyra)
Karma: 1
|
Senior Member |
|
|
If anyone wants a copy I have an excel spread sheet that has the cut schedule for making 4 jack-stands from 8' or 7' 2x4's. It can be easily modified for making 6 jack-stands. BTW it takes 8 8' 2x4's or 11 7' to make 4 jack-stands.
If you want a copy of the spreadsheet send me an email
midlf
at my ISP (replace all of this with @ )
Centurytel.net
and I'll attach the excel file in the reply.
The additional pictures I'll put in the album later tonight are step by step instructions on how I do it.
Steve Southworth
1974 Glacier TZE064V100150 (for workin on)
1975 Transmode TZE365V100394 (parts & spares)
Palmyra WI
|
|
|
|
| Re: [GMCnet] 12 Ton Jack-Stands [message #83188 is a reply to message #83149] |
Wed, 05 May 2010 13:40 |
gmcrv1
Messages: 839
Registered: August 2007
Location: Memphis
Karma: -1
|
Senior Member |
|
|
Steve,
Your pyramid stands are great! Just thought for those that want to take it
to the next
higher level, would you recommend using 4x4's for the bottom and/or top
rows? this would increase the height another 3 inches if using 4x4s top and
bottom yet would not change
the footprint. As mentioned earlier - often increasing the foot print
restricts access to undercarriage components.
Just a thought,
Tom Eckert
73 Glacier
N2VWN
Oakland, TN
On Wed, May 5, 2010 at 9:50 AM, Mr.erf ERFisher <mr.erfisher@gmail.com>wrote:
> cool, I have the album linked on my web page
>
> http://gmcmotorhome.info/rear.html#RAISING
>
>
> gene
>
>
> On Wed, May 5, 2010 at 7:02 AM, Steve Southworth <midlf@centurytel.net
> >wrote:
>
> >
> >
> > The CFO reminded me that she had taken a lot of pictures of the process
> of
> > building these jack-stands the last time I made some. I'll get those put
> in
> > the album later today.
> > --
> > Steve Southworth
> > 1974 Glacier TZE064V100150
> > Palmyra WI
> > _______________________________________________
> > GMCnet mailing list
> > List Information and Subscription Options:
> > http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
> >
>
>
>
> --
> Gene Fisher -- 74-23,77PB/ore/ca
> “Give a man a fish; you have fed him for today --- give him a URL and
> -------
> http://gmcmotorhome.info/
> Alternator Protection Cable
> http://gmcmotorhome.info/APC.html
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
| Re: [GMCnet] 12 Ton Jack-Stands [message #83192 is a reply to message #83188] |
Wed, 05 May 2010 13:56 |
midlf
Messages: 2212
Registered: July 2007
Location: SE Wisc. (Palmyra)
Karma: 1
|
Senior Member |
|
|
| gmcrv1 wrote on Wed, 05 May 2010 13:40 |
Steve,
Your pyramid stands are great! Just thought for those that want to take it
to the next
higher level, would you recommend using 4x4's for the bottom and/or top
rows? this would increase the height another 3 inches if using 4x4s top and
bottom yet would not change
the footprint. As mentioned earlier - often increasing the foot print
restricts access to undercarriage components.
Just a thought,
Tom Eckert
|
I would have no difficulty doing it that way. As you can see from the pictures I went an extra 6" just using blocking on the top of the Jack-Stands. It all really boils down to what ever you are comfortable doing. You have to decide for yourself what is safe. You could also just increase the length of each level by less than the 1" I used and it would give you height without making the base too large. As I said in one of the picture descriptions the height was determined by my floor jack and doing the stackup the way I did gave an acceptable, to me, base width that was wide enough to satisfy my safety concerns without being so large it interfered with my workspace. I most always had acceptable workspace on the Vette, and certainly do on the GMC.
Steve Southworth
1974 Glacier TZE064V100150 (for workin on)
1975 Transmode TZE365V100394 (parts & spares)
Palmyra WI
|
|
|
|
| Re: [GMCnet] 12 Ton Jack-Stands [message #83203 is a reply to message #83192] |
Wed, 05 May 2010 14:25 |
gmcrv1
Messages: 839
Registered: August 2007
Location: Memphis
Karma: -1
|
Senior Member |
|
|
Steve,
I'll be making a set of four for the rear. Under the front tires I use a
set of Snap-On alignment
stand. Like all S-O stuff it is really heavy duty. The downside is that it
only works with the wheels & tires on.
I had a set of those 3 ton Harbor Fright ratchet stands I used to use under
my MG, until one day after setting up one stand and jacking up the other
side the car came crashing down. The ratcheting edges and pawls just didn't
hold. Last time I checked that MG was not that heavy.
Tom Eckert
73 Glacier
N2VWN
Oakland, TN
On Wed, May 5, 2010 at 1:56 PM, Steve Southworth <midlf@centurytel.net>wrote:
>
>
> gmcrv1 wrote on Wed, 05 May 2010 13:40
> > Steve,
> >
> > Your pyramid stands are great! Just thought for those that want to take
> it
> > to the next
> > higher level, would you recommend using 4x4's for the bottom and/or top
> > rows? this would increase the height another 3 inches if using 4x4s top
> and
> > bottom yet would not change
> > the footprint. As mentioned earlier - often increasing the foot print
> > restricts access to undercarriage components.
> >
> > Just a thought,
> >
> >
> > Tom Eckert
>
>
> I would have no difficulty doing it that way. As you can see from the
> pictures I went an extra 6" just using blocking on the top of the
> Jack-Stands. It all really boils down to what ever you are comfortable
> doing. You have to decide for yourself what is safe. You could also just
> increase the length of each level by less than the 1" I used and it would
> give you height without making the base too large. As I said in one of the
> picture descriptions the height was determined by my floor jack and doing
> the stackup the way I did gave an acceptable, to me, base width that was
> wide enough to satisfy my safety concerns without being so large it
> interfered with my workspace. I most always had acceptable workspace on the
> Vette, and certainly do on the GMC.
>
> --
> Steve Southworth
> 1974 Glacier TZE064V100150
> Palmyra WI
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
|
|
|
|
| Re: [GMCnet] 12 Ton Jack-Stands [message #83273 is a reply to message #83271] |
Wed, 05 May 2010 22:20 |
midlf
Messages: 2212
Registered: July 2007
Location: SE Wisc. (Palmyra)
Karma: 1
|
Senior Member |
|
|
The jack-stand photo album has the step by step pictures and descriptions added.
Steve Southworth
1974 Glacier TZE064V100150 (for workin on)
1975 Transmode TZE365V100394 (parts & spares)
Palmyra WI
|
|
|
|
| Re: 12 Ton Jack-Stands [message #83280 is a reply to message #83103] |
Wed, 05 May 2010 23:30 |
Chr$
Messages: 2690
Registered: January 2004
Location: Scottsdale, AZ
Karma: 1
|
Senior Member |
|
|
I have had a block of wood split under my 66 Nova. I no longer trust wood as a primary method. I do use wood cribbing for secondary protection under the bogies or the front tires.
I like the 3 ton jack stands from Harbor fright. they are thicker and wider than the usual types. The "L" shape of the bottom of the jack stand legs also bite the concrete which gives me piece of mind. These also fit the front cross member of the coach nicely, and you can put a thick rubber sheet for some grip at the top.
They also stack nicely on their sides on top of my floor jack.
My two cents...
-Chr$: Perpetual SmartAss
Scottsdale, AZ
77 Ex-Kingsley 455 SOLD!
2010 Nomad 24 Ft TT 390W PV W/MPPT, EV4010 and custom cargo door.
Photosite: Chrisc GMC:"It has Begun" TT: "The Other Woman"
|
|
|
|
| Re: 12 Ton Jack-Stands [message #83322 is a reply to message #83280] |
Thu, 06 May 2010 09:55 |
midlf
Messages: 2212
Registered: July 2007
Location: SE Wisc. (Palmyra)
Karma: 1
|
Senior Member |
|
|
| Chr$ wrote on Wed, 05 May 2010 23:30 |
I have had a block of wood split under my 66 Nova. I no longer trust wood as a primary method. I do use wood cribbing for secondary protection under the bogies or the front tires.
I like the 3 ton jack stands from Harbor fright. they are thicker and wider than the usual types. The "L" shape of the bottom of the jack stand legs also bite the concrete which gives me piece of mind. These also fit the front cross member of the coach nicely, and you can put a thick rubber sheet for some grip at the top.
They also stack nicely on their sides on top of my floor jack.
My two cents...
|
I will agree on a single block of wood being unsuitable for the reason you noted. It can split and shift. I feel the multiple layers of my stand get around that, sorta like plywood vs a plain board.
As far as HF stands I've copied and pasted a bit from a previous post:
"I had a set of those 3 ton Harbor Fright ratchet stands I used to use under
my MG, until one day after setting up one stand and jacking up the other
side the car came crashing down. The ratcheting edges and pawls just didn't
hold. Last time I checked that MG was not that heavy.
Tom Eckert
73 Glacier"
If I had these I would inspect and, if necessary, clean up the ratchets and pawls with a file to make sure they had good bite. With the inconsistent quality of Chinese goods you may have a better set than Tom had.
Chris - check the swap section for my answer to your request.
Steve Southworth
1974 Glacier TZE064V100150 (for workin on)
1975 Transmode TZE365V100394 (parts & spares)
Palmyra WI
|
|
|
|
| Re: [GMCnet] 12 Ton Jack-Stands [message #83366 is a reply to message #83322] |
Thu, 06 May 2010 16:37 |
gmcrv1
Messages: 839
Registered: August 2007
Location: Memphis
Karma: -1
|
Senior Member |
|
|
Chris,
These were brand new Harbor Fright stands. I still have them - they are
useful for holding up a rear axle assembly. Only thing nice about the 3 ton
HF stands is that they have shiny enamel paint. I think the quality of the
HF stuff varies do to the different suppliers they may have. Some are
probably better then others. Raise the ratchet and give it a good smack to
make sure it is safe.
I also have an older set of 5/6 ton ratchet stands - also made in China -
very solid and stable. Use them all the time under an F150. Use to use
them under a 1961 MK IX Jaguar saloon - about the same weight as a Rolls or
Bentley, but that was before the D-I-V-O-R-C-E - sigh - for the cars - not
the divorce.
I will check them and see if the edges can be ground a little - just got
apprehensive after the crash.
I think we're up to 4 cents now,
Tom Eckert
73 Glacier
On Thu, May 6, 2010 at 9:55 AM, Steve Southworth <midlf@centurytel.net>wrote:
>
>
> Chr$ wrote on Wed, 05 May 2010 23:30
> > I have had a block of wood split under my 66 Nova. I no longer trust wood
> as a primary method. I do use wood cribbing for secondary protection under
> the bogies or the front tires.
> >
> > I like the 3 ton jack stands from Harbor fright. they are thicker and
> wider than the usual types. The "L" shape of the bottom of the jack stand
> legs also bite the concrete which gives me piece of mind. These also fit the
> front cross member of the coach nicely, and you can put a thick rubber sheet
> for some grip at the top.
> >
> > They also stack nicely on their sides on top of my floor jack.
> >
> > My two cents...
>
>
> I will agree on a single block of wood being unsuitable for the reason you
> noted. It can split and shift. I feel the multiple layers of my stand get
> around that, sorta like plywood vs a plain board.
>
> As far as HF stands I've copied and pasted a bit from a previous post:
>
> "I had a set of those 3 ton Harbor Fright ratchet stands I used to use
> under
> my MG, until one day after setting up one stand and jacking up the other
> side the car came crashing down. The ratcheting edges and pawls just didn't
> hold. Last time I checked that MG was not that heavy.
>
>
> Tom Eckert
> 73 Glacier"
>
>
>
> If I had these I would inspect and, if necessary, clean up the ratchets and
> pawls with a file to make sure they had good bite. With the inconsistent
> quality of Chinese goods you may have a better set than Tom had.
>
>
> Chris - check the swap section for my answer to your request.
>
> --
> Steve Southworth
> 1974 Glacier TZE064V100150
> Palmyra WI
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
| Re: [GMCnet] 12 Ton Jack-Stands [message #83384 is a reply to message #83366] |
Thu, 06 May 2010 18:43 |
 |
USAussie
Messages: 15912
Registered: July 2007
Location: Sydney, Australia
Karma: 6
|
Senior Member |
|
|
Tom / Steve,
THANKS!
All the Harbor Freight stands I have here in Australia are at least 8 years
old as we retired here in 2002. To date they've never dropped BUT since you
have noted this I WILL inspect them closely and whenever I use them I will
make sure the ratchet stops are fully engaged!
I did buy four three ton stands and four twelve ton stands from HF for
Double Trouble last year. I REALLY appreciate you calling my attention to
the problem you had with your three ton set. I've put it on my TTD list to
inspect them carefully when I get back there in June!
Looks like even the Chinese "don't make 'em like they used to," eh!
As far as your stands that collapsed I would take them back to the store you
bought them. Bring a friend with you to witness the conversation and tell
the manager what happened. I would be most surprised if he didn't take them
back and give you a new pair. They are defective, period, end of story!
Regards,
Rob Mueller
Sydney, Australia
AUS '75 Avion-The Blue Streak TZE365V100428
USA '75 Avion-Double Trouble TZE365V100426
-----Original Message-----
From: gmclist-bounces@temp.gmcnet.org
[mailto:gmclist-bounces@temp.gmcnet.org] On Behalf Of Tom Eckert
Sent: Friday, 7 May 2010 7:38 AM
To: gmclist@temp.gmcnet.org
Subject: Re: [GMCnet] 12 Ton Jack-Stands
Chris,
These were brand new Harbor Fright stands. I still have them - they are
useful for holding up a rear axle assembly. Only thing nice about the 3 ton
HF stands is that they have shiny enamel paint. I think the quality of the
HF stuff varies do to the different suppliers they may have. Some are
probably better then others. Raise the ratchet and give it a good smack to
make sure it is safe.
I also have an older set of 5/6 ton ratchet stands - also made in China -
very solid and stable. Use them all the time under an F150. Use to use
them under a 1961 MK IX Jaguar saloon - about the same weight as a Rolls or
Bentley, but that was before the D-I-V-O-R-C-E - sigh - for the cars - not
the divorce.
I will check them and see if the edges can be ground a little - just got
apprehensive after the crash.
I think we're up to 4 cents now,
Tom Eckert
73 Glacier
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Regards,
Rob M. (USAussie)
The Pedantic Mechanic
Sydney, Australia
'75 Avion - AUS - The Blue Streak TZE365V100428
'75 Avion - USA - Double Trouble TZE365V100426
|
|
|
|
Goto Forum:
Current Time: Sat Nov 16 21:48:50 CST 2024
Total time taken to generate the page: 0.00727 seconds
|
GMCforum
Search
Help
Register
Login
Home
