| [GMCnet] Control arm Feedback [message #76002] |
Mon, 08 March 2010 14:57  |
Steven Ferguson
Messages: 3447
Registered: May 2006
Karma: 0
|
Senior Member |
|
|
Guys,
These are the best numbers yet. Les Dahm, White Bear Lk. MN, just
finished up at SpecTrack alignment in Mesa. Gary Hartman was able to
send him out the door with 7 deg of caster. Les is really looking
forward to the trip back to MN. He says it steers with one finger.
If you have any feedback regarding your installation, I'd sure like
to get it...good or bad.
--
Steve Ferguson
'76 EII
Sierra Vista, AZ
Urethane bushing source
www.bdub.net/ferguson/
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
| Re: [GMCnet] Control arm Feedback [message #76026 is a reply to message #76002] |
Mon, 08 March 2010 18:59  |
 |
ljdavick
Messages: 3548
Registered: March 2007
Location: Fremont, CA
Karma: -3
|
Senior Member |
|
|
How did he do it? Is there some special wizardry going on?
Ljdavick at comcast.net
On Mar 8, 2010, at 12:57 PM, Steven Ferguson <botiemad11@gmail.com>
wrote:
> Guys,
> These are the best numbers yet. Les Dahm, White Bear Lk. MN, just
> finished up at SpecTrack alignment in Mesa. Gary Hartman was able to
> send him out the door with 7 deg of caster. Les is really looking
> forward to the trip back to MN. He says it steers with one finger.
> If you have any feedback regarding your installation, I'd sure like
> to get it...good or bad.
>
> --
> Steve Ferguson
> '76 EII
> Sierra Vista, AZ
> Urethane bushing source
> www.bdub.net/ferguson/
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Larry Davick
A Mystery Machine
1976(ish) Palm Beach
Fremont, Ca
Howell EFI + EBL + Electronic Dizzy
|
|
|
|
| Re: [GMCnet] Control arm Feedback [message #76034 is a reply to message #76026] |
Mon, 08 March 2010 20:06 |
Steven Ferguson
Messages: 3447
Registered: May 2006
Karma: 0
|
Senior Member |
|
|
Offset bushings on the rear ears of the upper control arms.
On Mon, Mar 8, 2010 at 5:59 PM, Larry Davick <ljdavick@comcast.net> wrote:
> How did he do it? Is there some special wizardry going on?
>
> Ljdavick at comcast.net
>
> On Mar 8, 2010, at 12:57 PM, Steven Ferguson <botiemad11@gmail.com>
> wrote:
>
>> Guys,
>> These are the best numbers yet. Les Dahm, White Bear Lk. MN, just
>> finished up at SpecTrack alignment in Mesa. Gary Hartman was able to
>> send him out the door with 7 deg of caster. Les is really looking
>> forward to the trip back to MN. He says it steers with one finger.
>> If you have any feedback regarding your installation, I'd sure like
>> to get it...good or bad.
>>
>> --
>> Steve Ferguson
>> '76 EII
>> Sierra Vista, AZ
>> Urethane bushing source
>> www.bdub.net/ferguson/
>> _______________________________________________
>> GMCnet mailing list
>> List Information and Subscription Options:
>> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
--
Steve Ferguson
'76 EII
Sierra Vista, AZ
Urethane bushing source
www.bdub.net/ferguson/
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
GMCforum
Search
Help
Register
Login
Home
