Intermediate Shaft Bearing [message #69946] |
Thu, 07 January 2010 16:34 |
Chr$
Messages: 2690 Registered: January 2004 Location: Scottsdale, AZ
Karma: 1
|
Senior Member |
|
|
Anyone replaced the bearing on the RH intermediate shaft? Looks like i need to make a jig to get this thing on the press to pop the bearing apart.
Reason I need to do this:
The 3.21 FD has a different shaft, we all know that, and where my flanges are compatible with the CV joints, the intermediate shaft bracket has a different hole pattern than the original one. To further complicate matters, the OD of the bearing in this lovely thing is smaller than the original, looks to be 2.5" where the orig is 3" (I have not used a caliper on it yet).
So, I need to take both of them apart, then source a bearing that has the ID of the 3.21 shaft and the OD of the 3.07 shaft's bracket housing.
Fun huh?
I didn't come across this in my research. I think I will add this info to the FAQ on B-dub's site when I get all the sizes nailed down. Might be good to put on the ratio chart showing all the combinations of Final Drives and Chain Ratios.
Chris "With the tranny 95% installed" Choffat.
-Chr$: Perpetual SmartAss
Scottsdale, AZ
77 Ex-Kingsley 455 SOLD!
2010 Nomad 24 Ft TT 390W PV W/MPPT, EV4010 and custom cargo door.
Photosite: Chrisc GMC:"It has Begun" TT: "The Other Woman"
|
|
|
|
|
|
Re: [GMCnet] Intermediate Shaft Bearing [message #70467 is a reply to message #70464] |
Mon, 11 January 2010 08:35 |
Steven Ferguson
Messages: 3447 Registered: May 2006
Karma: 0
|
Senior Member |
|
|
Don't know what to say about that Rob. I found one in stock at the local NAPA.
However, now that you've done it, it won't have to be done again and
you KNOW it's good!
I think that's what it's really all about. Besides, what else would
you have done that day:>)
On Mon, Jan 11, 2010 at 6:15 AM, Rob Mueller <robmueller@iinet.net.au> wrote:
> Steve,
>
> I thought mine was no good as it had a bit of side play. I ordered a
> replacement from Cinnabar as they were the only people that had one when I
> wanted it. I do remember that it wasn't cheap! When it got here it was
> exactly like the one I replaced!
>
> Regards,
> Rob Mueller
> Sydney, Australia
> AUS '75 Avion-The Blue Streak TZE365V100428
> USA '75 Avion-Double Trouble TZE365V100426
>
> -----Original Message-----
> From: gmclist-bounces@temp.gmcnet.org
> [mailto:gmclist-bounces@temp.gmcnet.org] On Behalf Of Steven Ferguson
> Sent: Tuesday, 12 January 2010 12:09 AM
> To: gmclist@temp.gmcnet.org
> Subject: Re: [GMCnet] Intermediate Shaft Bearing
>
> I figured why put a new eng & trans in without replacing it. Pretty
> simple to do it when the drive shaft is out rather than wait til it
> starts failing.
>
> --
> Steve Ferguson
> '76 EII
> Sierra Vista, AZ
> Urethane bushing source
> www.bdub.net/ferguson/
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
--
Steve Ferguson
'76 EII
Sierra Vista, AZ
Urethane bushing source
www.bdub.net/ferguson/
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|