GMCforum
For enthusiast of the Classic GMC Motorhome built from 1973 to 1978. A web-based mirror of the GMCnet mailing list.
Home » Public Forums » GMCnet » Any ideas? (Leaky sink ?)
icon14.gif  Any ideas? [message #67803] Fri, 18 December 2009 23:58 Go to next message
gmcdude76   United States
Messages: 102
Registered: December 2009
Location: Northern Ca
Karma: 1
Senior Member
What am i doing wrong?
This might be a dumb question to pose.I have a 76 Birchaven transmode.i was fixing the sink and i bought a moen 1200 cartridge to replace in my sink?i found

I think i followed the instructions tried two different times and still had leaks from the base of the faucet and on the top dident seem to effect the original issue.i had a leaky sink. Laughing

I also have a leak coming from under the toilet i beleive its the theatford model.but i am not a plumber by any means.any help or idea would be great.i also found onlineis a tech design on bdubs site.i referd to each plans and dident get anyplace??


Thanks for any info

Gmc76Birchaven 23'94947

Report message to a moderator

Re: Any ideas? [message #67814 is a reply to message #67803] Sat, 19 December 2009 08:51 Go to previous messageGo to next message
petemosss is currently offline  petemosss   United States
Messages: 221
Registered: August 2008
Location: Jacksonville, Florida
Karma: 0
Senior Member
Older Moen especially need OEM Moen carts and orings. Look for real plumbing parts house. Accept no knockoffs. Many moons of repair parts exp. here.

Pete 74 Canyon Lands 26' "Emery"

Report message to a moderator

Re: Any ideas? [message #67821 is a reply to message #67803] Sat, 19 December 2009 11:01 Go to previous messageGo to next message
Chr$ is currently offline  Chr$   United States
Messages: 2690
Registered: January 2004
Location: Scottsdale, AZ
Karma: 1
Senior Member
These days, I feel it is better to just replace the whole faucet as there are many low cost and good quality choices, plus you get updated styling.

My 2 cents.

-Chr$: Perpetual SmartAss
Scottsdale, AZ

77 Ex-Kingsley 455 SOLD!
2010 Nomad 24 Ft TT 390W PV W/MPPT, EV4010 and custom cargo door.
Photosite: Chrisc GMC:"It has Begun" TT: "The Other Woman"

Report message to a moderator

Re: Any ideas? [message #67823 is a reply to message #67803] Sat, 19 December 2009 12:13 Go to previous messageGo to next message
gmcdude76   United States
Messages: 102
Registered: December 2009
Location: Northern Ca
Karma: 1
Senior Member
Thanks

I did make sure i bought moen parts and the directions said to simply replace the cartridge(moen 1200)i followed the destructions and it dident repair it??one thing i couldent tell is it said make sure the red dot on the cartridge faces front.there wasent a red dot on the replacement.the old one did have a red mark but i shoulda took better care to see how each part was set.

it said nothing about o rings or the like in fact it had new ones on the new catridge.one thing i thouhgt was odd is when i shut off the main water valve it had to be tured backwards or counter clockwise is this normal?

but thanks for the input.

Gmc76Birchaven 23'94947

Report message to a moderator

Re: Any ideas? [message #67826 is a reply to message #67823] Sat, 19 December 2009 12:56 Go to previous messageGo to next message
wally is currently offline  wally   United States
Messages: 643
Registered: August 2004
Location: Omaha Nebraska
Karma: 5
Senior Member
gmcdude76 wrote on Sat, 19 December 2009 12:13

Thanks

I did make sure i bought moen parts and the directions said to simply replace the cartridge(moen 1200)i followed the destructions and it dident repair it??one thing i couldent tell is it said make sure the red dot on the cartridge faces front.there wasent a red dot on the replacement.the old one did have a red mark but i shoulda took better care to see how each part was set.

it said nothing about o rings or the like in fact it had new ones on the new catridge.one thing i thouhgt was odd is when i shut off the main water valve it had to be tured backwards or counter clockwise is this normal?

but thanks for the input.

Bill Massey has the Moen faucet pdf at
http://www.bdub.net/manuals/index.html
The spout O-rings #137 might be the problem if you get the leak when the faucet is turned on. There might be some crud inside the spout where the O-rings ride and you can clean that off with a brillo pad or something like that. The rings should be lubed with some silicone grease so the spout can swivel and not tear up the rings.
HTH

Wally Anderson
Omaha NE
75 Glenbrook

Report message to a moderator

Re: Any ideas? [message #67828 is a reply to message #67803] Sat, 19 December 2009 14:38 Go to previous messageGo to next message
kingd is currently offline  kingd   Canada
Messages: 592
Registered: June 2004
Karma: 2
Senior Member
To GMCDUDE, if you turn on the faucet with the cartridge fully installed but before you put the handle back on, you can see if the leak is from around the cartidge(maybe). As has been posted, the leaked could be from the spout. The O-rings wear(a tiny bit) every time the spout is swivelled.

The "dot" is probaly to get the hot and cold correct. If the hot is now on the other side than it used to be, remove the "clip",
(I presume the GMC faucet is like the Moens I know) and rotate
the cartridge 180 degrees. Of course this assume you have hot and cold water. Turning of one of the lines is an alternative.
It's not funny when you get hot when expecting cold and vicea versa.

DAVE KING

DAVE KING lurker, wannabe Toronto, Ontario, Canada

Report message to a moderator

Re: [GMCnet] Any ideas? [message #67830 is a reply to message #67828] Sat, 19 December 2009 16:07 Go to previous message
USAussie is currently offline  USAussie   United States
Messages: 15912
Registered: July 2007
Location: Sydney, Australia
Karma: 6
Senior Member
G'day,

The kitchen faucet in Double Trouble leaked so I took it apart and put a
rebuild kit in it from Delta and that fixed the leak, kinda.

We noticed that if you turned it on with no city water pressure on or the
pump off and reduced the line pressure to zero it would drip.

Turn the pump on for a few second to build up the line pressure and it would
stop.

Regards,
Rob


-----Original Message-----
From: gmclist-bounces@temp.gmcnet.org
[mailto:gmclist-bounces@temp.gmcnet.org] On Behalf Of Dave King
Sent: Sunday, 20 December 2009 7:39 AM
To: gmclist@temp.gmcnet.org
Subject: Re: [GMCnet] Any ideas?



To GMCDUDE, if you turn on the faucet with the cartridge fully installed but
before you put the handle back on, you can see if the leak is from around
the cartidge(maybe). As has been posted, the leaked could be from the spout.
The O-rings wear(a tiny bit) every time the spout is swivelled.

The "dot" is probaly to get the hot and cold correct. If the hot is now on
the other side than it used to be, remove the "clip",
(I presume the GMC faucet is like the Moens I know) and rotate
the cartridge 180 degrees. Of course this assume you have hot and cold
water. Turning of one of the lines is an alternative.
It's not funny when you get hot when expecting cold and vicea versa.

DAVE KING
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

Regards, Rob M. (USAussie) The Pedantic Mechanic Sydney, Australia '75 Avion - AUS - The Blue Streak TZE365V100428 '75 Avion - USA - Double Trouble TZE365V100426

Report message to a moderator

Previous Topic: Re: [GMCnet] GMC's In PA
Next Topic: Duo-Therm Sure Start photos wanted
Goto Forum:
  


Current Time: Tue Nov 19 23:21:53 CST 2024

Total time taken to generate the page: 0.01447 seconds
.:: Contact :: Home ::.

Powered by: FUDforum 3.1.1.
Copyright ©2001-2021 FUDforum Bulletin Board Software