| Need a source for Dinette edging [message #67493] |
Tue, 15 December 2009 09:42  |
 |
Matt Colie
Messages: 8547
Registered: March 2007
Location: S.E. Michigan
Karma: 7
|
Senior Member |
|
|
The dinette of my 73 is 5/8 plywood with a plastic T-mold edging. Well, some of it is. Some of it is now plain plywood edge with a groove cut in it. I would like to replace the edging, but I can't find a source for 5/8 material. There are lots of places I can get 3/4 or 13/16, but no 5/8.
I have put many feet of veneer edging on plywood, but I really don't want the hard edges on the dinette. I also don't want to tape and plane the edges of the dinette unless there is just no choice at all.
Matt
Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL, GMCES
Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum Brakes with Applied Control Arms
SE Michigan - Near DTW - Twixt A2 and Detroit
|
|
|
|
|
|
| Re: [GMCnet] Need a source for Dinette edging [message #67561 is a reply to message #67504] |
Tue, 15 December 2009 18:35  |
Marcel Bourgon
Messages: 37
Registered: December 2005
Karma: 0
|
Member |
|
|
I have some white t molding in my shop and you are welcome to some. It is a
bit larger than 3/4" but you only need to take some time with a razor blade
and trim in down. A good source is Outwater plastics. You can find them on
the net
Marcel in El Paso
----- Original Message -----
From: "Wally Anderson" <wallyand@aim.com>
To: <gmclist@temp.gmcnet.org>
Sent: Tuesday, December 15, 2009 10:23 AM
Subject: Re: [GMCnet] Need a source for Dinette edging
>
>
> mcolie wrote on Tue, 15 December 2009 09:42
>> The dinette of my 73 is 5/8 plywood with a plastic T-mold edging. Well,
>> some of it is. Some of it is now plain plywood edge with a groove cut in
>> it. I would like to replace the edging, but I can't find a source for
>> 5/8 material. There are lots of places I can get 3/4 or 13/16, but no
>> 5/8.
>>
>> I have put many feet of veneer edging on plywood, but I really don't want
>> the hard edges on the dinette. I also don't want to tape and plane the
>> edges of the dinette unless there is just no choice at all.
>>
>> Matt
>
> Hey Matt,
> These guys show 5/8 T-mold in seven types.
> http://t-molding.com/store/home.php?cat=2
> HTH
> --
> Wally Anderson
> 1975 Glenbrook
> Megasquirt 455 port injection science project-On the road 5918 miles
> Omaha Nebraska
> Greater Midwest Classics
> GMCES
> http://wallyandsue.blogspot.com/
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
GMCforum
Search
Help
Register
Login
Home
