Hot Water Heater Bypass [message #65195] |
Sat, 21 November 2009 14:32 |
Jon payne
Messages: 495 Registered: May 2008
Karma: 1
|
Senior Member |
|
|
Hi all,
I have been putting off winterizing the water system until now. Next week we will be much colder, high in the 30's so I need to get this done.
I plan to pump in the RV antifreeze but I know I need to bypass the water heater. I am looking for some ideas. As I see it I need to add a shut off valve in the line to the HW heater cold water inlet. The challenge I see is the short amount of line between cold water tee fitting and the HW tank inlet. My idea is to extend that line, using a reinforced flexible hose, so that I can add a shut off.
If anyone has some pictures of how they did there it would be appreciated.
Jon
Jon Payne
76 Palm Beach
Westfield,IN
|
|
|
Re: [GMCnet] Hot Water Heater Bypass [message #65196 is a reply to message #65195] |
Sat, 21 November 2009 14:39 |
Mr ERFisher
Messages: 7117 Registered: August 2005
Karma: 2
|
Senior Member |
|
|
here you go
http://gmcmotorhome.info/WINTER.html
gene
On Sat, Nov 21, 2009 at 12:33 PM, Jon Payne <embrep@sbcglobal.net> wrote:
>
>
> Hi all,
>
> I have been putting off winterizing the water system until now. Next week
> we will be much colder, high in the 30's so I need to get this done.
>
> I plan to pump in the RV antifreeze but I know I need to bypass the water
> heater. I am looking for some ideas. As I see it I need to add a shut off
> valve in the line to the HW heater cold water inlet. The challenge I see is
> the short amount of line between cold water tee fitting and the HW tank
> inlet. My idea is to extend that line, using a reinforced flexible hose, so
> that I can add a shut off.
>
> If anyone has some pictures of how they did there it would be appreciated.
>
> Jon
>
>
>
>
> --
> Jon Payne/
> 76 Palm Beach/
> Westfield,IN
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
--
Gene Fisher -- 74-23,77PB/ore/ca
“Give a man a fish; you have fed him for today --- give him a URL and
-------
http://gmcmotorhome.info/
Alternator Protection Cable
http://gmcmotorhome.info/APC.html
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
Re: Hot Water Heater Bypass [message #65200 is a reply to message #65195] |
Sat, 21 November 2009 15:01 |
Ken Burton
Messages: 10030 Registered: January 2004 Location: Hebron, Indiana
Karma: 10
|
Senior Member |
|
|
Jon Payne wrote on Sat, 21 November 2009 14:32 | Hi all,
I have been putting off winterizing the water system until now. Next week we will be much colder, high in the 30's so I need to get this done.
I plan to pump in the RV antifreeze but I know I need to bypass the water heater. I am looking for some ideas. As I see it I need to add a shut off valve in the line to the HW heater cold water inlet. The challenge I see is the short amount of line between cold water tee fitting and the HW tank inlet. My idea is to extend that line, using a reinforced flexible hose, so that I can add a shut off.
If anyone has some pictures of how they did there it would be appreciated.
Jon
|
Go get an RV how Water heater bypass kit for less than $20 at just about any RV store.
http://www.pplmotorhomes.com/parts/rv-pumps-water/rv-winterizing-bypass.htm
http://www.ehow.com/how_4546786_rv-water-heater-bypass-kit.html
I would drain the tank and blow out the lines first before engaging the valves on the kit and installing the antifreeze.
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
|
|
|
Re: Hot Water Heater Bypass [message #65204 is a reply to message #65195] |
Sat, 21 November 2009 15:41 |
Rick Williams
Messages: 256 Registered: July 2004
Karma: 0
|
Senior Member |
|
|
John
Ken's suggestion for a bypass kit from an rv store is good. They are very convenient and fit in a small space.
That being said, I have had bad luck with the valves in those kits. They have leaked and just this fall while winterizing, one of the valves would not turn. After I removed it, I found that a rubber seal within the valve had torn and jammed the valve. So it was off to the hardware store. I bought three independant, 1/4 turn ball valves. They take up more room and it is tight under the bathroom sink but it works well.
You need to block the flow of water to both the inlet and outlet of the water heater and also provide the bypass.
The kits come with 2 three-way valves which accomplish the same thing as the 3 individual valves. Flex lines from the hardware store can be used.
Rick
Rick Williams
Bliss, Michigan
1978 Eleganza II
|
|
|
|