[GMCnet] Re: Axle Rebuild [message #366818 is a reply to message #366812] |
Wed, 15 September 2021 22:51 |
jimk
Messages: 6734 Registered: July 2006 Location: Belmont, CA
Karma:
|
Senior Member |
|
|
Be sure you can return the units as the NEW units Might have a different
spline.
Yes we supply a Rebuilt assembly by a firm that has a special "Scuffing"
machine and then install a larger ball and replace or rebuild the unit and
use the original axels.
We have encountered several rebuilders that only install larger ball only
and not touch other parts.
On Wed, Sep 15, 2021 at 6:44 PM Ken Henderson
wrote:
> Tony,
>
> Yes all of your ideas are feasible:
>
> 1. If it hasn't already been done, you CAN swap sides with the axles,
> achieving "new" wear areas. I'd "rebuild" them while they're out anyway
> (new grease and outer boots).
>
> 2/3. Toro and Eldo axles use the same CV joints (the only difference is
> that one of the Eldo axles has a damper weight on the axle). BUT, the
> original design CV's have become so scarce that most "rebuilt" ones are of
> a different design, having a different spline. So, the "rebuilders" have
> to provide "new" shafts with that spline, which is totally incompatible
> with our old longer shafts. When that first became a problem a few years
> ago, I went to the local NAPA and had them show me the computer photo of
> what they were offering. They showed both our design, which is distinctive
> in appearance, and the new one. I told them to order all the axles in
> their system, and I'd take all the "old" ones and only those. They did and
> I did. I think I got 3 out of 12. Good luck today.
>
> In case you don't know, the inner boots are probably still good. You DO
> NOT want to remove the sheet metal cans covering the inner joints: After
> removing the outer joints, remove the small clamp securing the inner boot
> to the axle. Put a board on the floor and hold the axle vertical by the
> inner joint. "Drop" the outer end of the axle gently onto the board. The
> inner cover will be dislodged, giving you access to the inner joint without
> removing the can. It's really not necessary to re-install the small clamp
> on the inner boot -- I've never seen one leak.
>
> HTH,
>
> Ken H.
>
> On Wed, Sep 15, 2021 at 9:08 PM wrote:
>
>> I want to rebuild my axles. There is a lot of slop and noticeable
>> vibration when accelerating, particularly from a stop. I have scoured
> the
>> forum for
>> suggestions. I’ve been told the originals are not available. Can I:
>> 1. Swap them side to side putting the worn areas on the deceleration
> side.
>> 2. Buy Toronado axles on eBay. Take the cv joints off and put them on my
>> axles.
>> 3. Buy eldorado axles and do the same as 2.
>>
>> I have read that there are correct Toronado axles and incorrect ones, but
>> I don’t know how to tell them apart.
>>
>> What are your recommendations? What are the pitfalls?
>>
>> Many thanks
>> --
>> 1974 455, 90,000 miles, pertronix, aluminum rad, headers
>> Port Colborne, ON Canada. Southern end of the Welland Canal
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
>
--
Jim Kanomata ASE
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.gmcrvparts.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502
|
|
|