Home » Public Forums » GMCnet » WHERE TO INSERT BLOCKING AT THE BOGIES
WHERE TO INSERT BLOCKING AT THE BOGIES [message #366224] |
Thu, 19 August 2021 14:19 |
g r a n t
Messages: 22 Registered: March 2021
Karma: 0
|
Junior Member |
|
|
Hello! We're heading out for vacation shortly and sadly without the GMC. This will be the first time I won't have a chance to re-inflate the bags so I'm looking to put in some wood blocks under the bogies while I am away.
Apologies but my short search did not come up with a photo of were EXACTLY to place the wood blocks.
I don't want to mesh anything up. Does anyone have a photo or clear description of where to block under the bogies?
I have to run up to the storage lot and don't want make several trips.
THANK YOU....!
G
1975 Eleganza
Toronto, ON
|
|
|
|
Re: WHERE TO INSERT BLOCKING AT THE BOGIES [message #366227 is a reply to message #366226] |
Thu, 19 August 2021 18:09 |
g r a n t
Messages: 22 Registered: March 2021
Karma: 0
|
Junior Member |
|
|
Thanks Matt. They’re in place now. I prefer to play dumb (easy to do) with new to me things so I don’t mess something up. Interestingly, my suspension was at full height after almost two weeks. Up till now they would sag after 3-4 days. Bummed we can’t take it on this trip but have lots planned for the Fall. G.
1975 Eleganza
Toronto, ON
|
|
|
|
[GMCnet] Re: WHERE TO INSERT BLOCKING AT THE BOGIES [message #366229 is a reply to message #366226] |
Thu, 19 August 2021 19:33 |
jimk
Messages: 6734 Registered: July 2006 Location: Belmont, CA
Karma: 9
|
Senior Member |
|
|
Matt,
Cut a 2x4 15" long and lay it on top of the boggie case and release the
jack,
Since it is not going to be moving much, no need to knotch the ends a
little.
On Thu, Aug 19, 2021 at 3:24 PM Matt Colie wrote:
> g r a n t wrote on Thu, 19 August 2021 15:19
>> Hello! We're heading out for vacation shortly and sadly without the GMC.
> This will be the first time I won't have a chance to re-inflate the bags
>> so I'm looking to put in some wood blocks under the bogies while I am
> away.
>> Apologies but my short search did not come up with a photo of were
> EXACTLY to place the wood blocks.
>> I don't want to mesh anything up. Does anyone have a photo or clear
> description of where to block under the bogies?
>> I have to run up to the storage lot and don't want make several trips.
>>
>> THANK YOU....!
>> G
>
> Grant,
>
> No rocket science here, just place them under that bogie casting. The
> same place you would put a floor jack if you needed to.
>
> Matt
> --
> Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL,
> GMCES
> Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum
> Brakes with Applied Control Arms
> SE Michigan - Near DTW - Twixt A2 and Detroit
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
>
--
Jim Kanomata ASE
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.gmcrvparts.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502
|
|
|
[GMCnet] Re: WHERE TO INSERT BLOCKING AT THE BOGIES [message #366231 is a reply to message #366228] |
Thu, 19 August 2021 23:19 |
jimk
Messages: 6734 Registered: July 2006 Location: Belmont, CA
Karma: 9
|
Senior Member |
|
|
The two by four are mounted horizontal
On Thu, Aug 19, 2021 at 5:53 PM Matt Colie wrote:
> Grant,
>
> If they open the border, maybe you can make it to the international.
> Worth doing if you can.
>
> Matt
> --
> Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL,
> GMCES
> Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum
> Brakes with Applied Control Arms
> SE Michigan - Near DTW - Twixt A2 and Detroit
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
>
--
Jim Kanomata ASE
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.gmcrvparts.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502
|
|
|
Re: [GMCnet] Re: WHERE TO INSERT BLOCKING AT THE BOGIES [message #366234 is a reply to message #366229] |
Fri, 20 August 2021 07:12 |
Larry
Messages: 2875 Registered: January 2004 Location: Menomonie, WI
Karma: 10
|
Senior Member |
|
|
jimk wrote on Thu, 19 August 2021 19:33Matt,
Cut a 2x4 15" long and lay it on top of the boggie case and release the
jack,
Since it is not going to be moving much, no need to knotch the ends a
little.
Jim Kanomata ASE
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.gmcrvparts.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
I'm sorry, but I cannot picture in my pea brain what and where that 2X4 goes and why. Please explain and maybe a pic?
Larry
78 Royale w/500 Caddy
Menomonie, WI.
|
|
|
Re: [GMCnet] Re: WHERE TO INSERT BLOCKING AT THE BOGIES [message #366235 is a reply to message #366234] |
Fri, 20 August 2021 08:00 |
|
Matt Colie
Messages: 8547 Registered: March 2007 Location: S.E. Michigan
Karma: 7
|
Senior Member |
|
|
Larry wrote on Fri, 20 August 2021 08:12
I'm sorry, but I cannot picture in my pea brain what and where that 2X4 goes and why. Please explain and maybe a pic?
JimK wrote:
The two by four are mounted horizontal
Cut a 2x4 15" long and lay it on top of the boggie case and release the jack,
Since it is not going to be moving much, no need to knotch the ends a little.
Larry,
What Jim is saying is to cut a 2x4 15" long and lay it on the top of the bogie casting when the coach is jacked or aired up to a good height.
This will put it between the vertical parts of the swing arms. When the load is lowered, that piece will stop the lowering and be trapped in there. This could be a problem with many of the non-OE suspension modifications.
I like this idea, but I have never done this. In my years of moving heavy stuff, we always used blocks or cribbing under the load. So, I usually just air up the suspension and pile my shoring blocks of which I have more than a few around the barn under the bogie casting. My system is now tight enough that I have to let it down if I want it down.
Matt
Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL, GMCES
Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum Brakes with Applied Control Arms
SE Michigan - Near DTW - Twixt A2 and Detroit
|
|
|
Re: [GMCnet] Re: WHERE TO INSERT BLOCKING AT THE BOGIES [message #366237 is a reply to message #366235] |
Fri, 20 August 2021 11:00 |
|
Richard RV
Messages: 631 Registered: July 2012 Location: Full-timer for 12 years, ...
Karma: -17
|
Senior Member |
|
|
This is the first time I've heard of using a 2x4 block just above the bogey box casting. Trying to get my head around the forces involved.
It seems to me that the ~2000# wheel load acting on the ~18" horizontal bogey arm lever would potentially crush the end of the 2x4 which has to counteract that same load but using a much shorter (maybe ~6"?) lever arm along the vertical bogey arm. That would put the load on the 2x4 very close to the ultimate crushing strength, of say Doug-Fir, parallel to the grain. The curved bogey arm wouldn't present much bearing area initially, but would compress and potentially start cracking along the grain.
Again, first time hearing about this and I have no experience with it and Jim K does. Anyone else use the word block above the bogey box?
If there's no danger of the wood crushing and splitting it certainly would be the fastest way to relieve pressure on the airbags. Blocking under the bogey boxes and relieving pressure on the airbags takes more time, but takes pressure off of both the airbags and tires.
Richard
'77 Birchaven TZE...777;
'76 Palm Beach under construction;
‘76 Edgemont waiting its turn
|
|
|
[GMCnet] Re: WHERE TO INSERT BLOCKING AT THE BOGIES [message #366238 is a reply to message #366235] |
Fri, 20 August 2021 10:36 |
Ken Henderson
Messages: 8726 Registered: March 2004 Location: Americus, GA
Karma: 9
|
Senior Member |
|
|
I've got 2 pieces of 6"x6" cut to the height beneath the normal bogie
height. A cabinet handle on each makes it easy to maneuver. When I
installed the Manny Reaction Arms, the center pivot mounting bolt
interfered with those blocks until I cut a bolt-head-width slot across the
top of each. I've never been able to stop ALL my leaks, so those blocks
always go under when I'm parking for a long time.
Ken H.
On Fri, Aug 20, 2021 at 9:01 AM Matt Colie wrote:
> Larry wrote on Fri, 20 August 2021 08:12
>> I'm sorry, but I cannot picture in my pea brain what and where that 2X4
> goes and why. Please explain and maybe a pic?
>>
>> JimK wrote:
>> The two by four are mounted horizontal
>> Cut a 2x4 15" long and lay it on top of the boggie case and release the
> jack,
>> Since it is not going to be moving much, no need to knotch the ends a
> little.
>
> Larry,
>
> What Jim is saying is to cut a 2x4 15" long and lay it on the top of the
> bogie casting when the coach is jacked or aired up to a good height.
> This will put it between the vertical parts of the swing arms. When the
> load is lowered, that piece will stop the lowering and be trapped in there.
> This could be a problem with many of the non-OE suspension modifications.
>
> I like this idea, but I have never done this. In my years of moving heavy
> stuff, we always used blocks or cribbing under the load. So, I usually
> just air up the suspension and pile my shoring blocks of which I have more
> than a few around the barn under the bogie casting. My system is now tight
> enough that I have to let it down if I want it down.
>
> Matt
> --
> Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL,
> GMCES
> Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum
> Brakes with Applied Control Arms
> SE Michigan - Near DTW - Twixt A2 and Detroit
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
Ken Henderson
Americus, GA
www.gmcwipersetc.com
Large Wiring Diagrams
76 X-Birchaven
76 X-Palm Beach
|
|
|
Re: [GMCnet] Re: WHERE TO INSERT BLOCKING AT THE BOGIES [message #366239 is a reply to message #366237] |
Fri, 20 August 2021 11:27 |
rjw
Messages: 697 Registered: September 2005
Karma: 4
|
Senior Member |
|
|
Richard RV wrote on Fri, 20 August 2021 12:00This is the first time I've heard of using a 2x4 block just above the bogey box casting. Trying to get my head around the forces involved.
It seems to me that the ~2000# wheel load acting on the ~18" horizontal bogey arm lever would potentially crush the end of the 2x4 which has to counteract that same load but using a much shorter (maybe ~6"?) lever arm along the vertical bogey arm. That would put the load on the 2x4 very close to the ultimate crushing strength, of say Doug-Fir, parallel to the grain. The curved bogey arm wouldn't present much bearing area initially, but would compress and potentially start cracking along the grain.
Again, first time hearing about this and I have no experience with it and Jim K does. Anyone else use the word block above the bogey box?
If there's no danger of the wood crushing and splitting it certainly would be the fastest way to relieve pressure on the airbags. Blocking under the bogey boxes and relieving pressure on the airbags takes more time, but takes pressure off of both the airbags and tires.
Richard
I also am not understanding how the above the bogey arm blocking works. Ever since day one, 23 years ago, I've just put some 4x4 and 2x4 x ~ 24" pieces under each casting to desired height. I pretty much use wood cribbing to support the coach, rather than jack stands which I think could move, when I work under the coach.
Richard
76 Palm Beach
SE Michigan
www.PalmBeachGMC.com
Roller Cam 455, TBI+EBL, 3.42 FD, 4 Bag, Macerator, Lenzi (brakes, vacuum system, front end stuff), Manny Tranny, vacuum step, Tankless + OEM water heaters.
|
|
|
[GMCnet] Re: WHERE TO INSERT BLOCKING AT THE BOGIES [message #366240 is a reply to message #366239] |
Fri, 20 August 2021 11:48 |
Keith V
Messages: 2337 Registered: March 2008 Location: Mounds View,MN
Karma: 0
|
Senior Member |
|
|
Uh, there's NO WAY a 2x4 would do anything if put on top of the airbags, the bags are significantly bigger than the bogie mounts, even the cones are bigger.
If there was no airbag, then it could work, but I'd rather use a 4x4.
Or maybe you could put something below the bags? Kinda weird though
Keith Vasilakes
Mounds View MN
76 exRoyale
MicroLevel
________________________________
From: RJW
Sent: Friday, August 20, 2021 11:27 AM
To: gmclist@list.gmcnet.org
Subject: [GMCnet] Re: WHERE TO INSERT BLOCKING AT THE BOGIES
Richard RV wrote on Fri, 20 August 2021 12:00
> This is the first time I've heard of using a 2x4 block just above the bogey box casting. Trying to get my head around the forces involved.
>
> It seems to me that the ~2000# wheel load acting on the ~18" horizontal bogey arm lever would potentially crush the end of the 2x4 which has to
> counteract that same load but using a much shorter (maybe ~6"?) lever arm along the vertical bogey arm. That would put the load on the 2x4 very
> close to the ultimate crushing strength, of say Doug-Fir, parallel to the grain. The curved bogey arm wouldn't present much bearing area initially,
> but would compress and potentially start cracking along the grain.
>
> Again, first time hearing about this and I have no experience with it and Jim K does. Anyone else use the word block above the bogey box?
>
> If there's no danger of the wood crushing and splitting it certainly would be the fastest way to relieve pressure on the airbags. Blocking under
> the bogey boxes and relieving pressure on the airbags takes more time, but takes pressure off of both the airbags and tires.
>
> Richard
I also am not understanding how the above the bogey arm blocking works. Ever since day one, 23 years ago, I've just put some 4x4 and 2x4 x ~ 24"
pieces under each casting to desired height. I pretty much use wood cribbing to support the coach, rather than jack stands which I think could move,
when I work under the coach.
--
Richard
76 Palm Beach
SE Michigan
www.PalmBeachGMC.com
Roller Cam 455, TBI+EBL, 3.42 FD, 4 Bag, Macerator, Lenzi (brakes, vacuum system, front end stuff), Manny Tranny, vacuum step, Tankless + OEM water
heaters.
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
Keith Vasilakes
Mounds View. MN
75 ex Royale GMC
ask me about MicroLevel
Cell, 763-732-3419
My427v8@hotmail.com
|
|
|
[GMCnet] Re: WHERE TO INSERT BLOCKING AT THE BOGIES [message #366244 is a reply to message #366240] |
Fri, 20 August 2021 17:18 |
jimk
Messages: 6734 Registered: July 2006 Location: Belmont, CA
Karma: 9
|
Senior Member |
|
|
!5" and when you put in a slight notch , the curved upright will not split
the wood.
I have had several do it as a last resort.
The Q Bag does not interfere, only the Paddle of a anotherdesign, in that
case remove the paddle.
I personally have traveled 120 miles that way.
On Fri, Aug 20, 2021 at 9:48 AM Keith V wrote:
> Uh, there's NO WAY a 2x4 would do anything if put on top of the airbags,
> the bags are significantly bigger than the bogie mounts, even the cones are
> bigger.
>
> If there was no airbag, then it could work, but I'd rather use a 4x4.
> Or maybe you could put something below the bags? Kinda weird though
>
> Keith Vasilakes
> Mounds View MN
> 76 exRoyale
> MicroLevel http://www.gmcmotorhomemarketplace.com/vasilakes/microlevel_intro.pdf>
>
>
> ________________________________
> From: RJW
> Sent: Friday, August 20, 2021 11:27 AM
> To: gmclist@list.gmcnet.org
> Subject: [GMCnet] Re: WHERE TO INSERT BLOCKING AT THE BOGIES
>
> Richard RV wrote on Fri, 20 August 2021 12:00
>> This is the first time I've heard of using a 2x4 block just above the
> bogey box casting. Trying to get my head around the forces involved.
>>
>> It seems to me that the ~2000# wheel load acting on the ~18" horizontal
> bogey arm lever would potentially crush the end of the 2x4 which has to
>> counteract that same load but using a much shorter (maybe ~6"?) lever
> arm along the vertical bogey arm. That would put the load on the 2x4 very
>> close to the ultimate crushing strength, of say Doug-Fir, parallel to
> the grain. The curved bogey arm wouldn't present much bearing area
> initially,
>> but would compress and potentially start cracking along the grain.
>>
>> Again, first time hearing about this and I have no experience with it
> and Jim K does. Anyone else use the word block above the bogey box?
>>
>> If there's no danger of the wood crushing and splitting it certainly
> would be the fastest way to relieve pressure on the airbags. Blocking under
>> the bogey boxes and relieving pressure on the airbags takes more time,
> but takes pressure off of both the airbags and tires.
>>
>> Richard
>
> I also am not understanding how the above the bogey arm blocking works.
> Ever since day one, 23 years ago, I've just put some 4x4 and 2x4 x ~ 24"
> pieces under each casting to desired height. I pretty much use wood
> cribbing to support the coach, rather than jack stands which I think could
> move,
> when I work under the coach.
>
> --
> Richard
> 76 Palm Beach
> SE Michigan
> www.PalmBeachGMC.com
>
>
> Roller Cam 455, TBI+EBL, 3.42 FD, 4 Bag, Macerator, Lenzi (brakes, vacuum
> system, front end stuff), Manny Tranny, vacuum step, Tankless + OEM water
> heaters.
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
>
--
Jim Kanomata ASE
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.gmcrvparts.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502
|
|
|
Goto Forum:
Current Time: Sat Oct 05 02:04:27 CDT 2024
Total time taken to generate the page: 0.00863 seconds
|