Home » Public Forums » GMCnet » Problem with brass body proportioning valve (Read about it in Winter 2021 Vintage RVing)
Re: [GMCnet] Re: Problem with brass body proportioning valve [message #365372 is a reply to message #365365] |
Mon, 12 July 2021 10:34 |
Bill Van Vlack
Messages: 419 Registered: September 2015 Location: Guemes Island, Washington
Karma: 14
|
Senior Member |
|
|
James Hupy wrote on Sun, 11 July 2021 23:33The disc brakes require more hydraulic pressure to operate than the drum
brakes do. That is why the engineers limited the pressure to the drum
brakes. When you have all discs on a coach, there needs to be the same
amount of pressure to front and rear, and no delay to the front brakes like
there is with a combination disc/drum system. Not too complex, really.
Jim Hupy
Salem, Oregon
That makes sense, but it gets more complex when trying to understand why the GMC Motorhome engineers did not do it that way. If I understand Dave Lenzi's article correctly, the GMCMH disk/drum coach came with a steel combination valve that provided the same amount of pressure to the front and rear brakes (after the front brake delay).
Bill Van Vlack
'76 Royale; Guemes Island, Washington; Twin bed, full (DS) side bath, Brazilian Redwood counter and settee tops,455, 6KW generator; new owner a/o mid November 2015.
|
|
|
[GMCnet] Re: Problem with brass body proportioning valve [message #365374 is a reply to message #365372] |
Mon, 12 July 2021 10:50 |
James Hupy
Messages: 6806 Registered: May 2010
Karma: -62
|
Senior Member |
|
|
Because they could not "just pick some part off of another GM brand" to do
that exact job, they went with what was available at the time. Just my best
guess, anyway.
They engineered some weird stuff in the 70's. Ask me about Converted
gasoline engines to diesel, set crosswise on top of the transaxle in the
front end of Olds "C" bodies. You had to remove the motor mount fasteners
to get at the glow plugs and injectors. WHAT A PITA that was.
Jim Hupy
Salem, Oregon
On Mon, Jul 12, 2021, 8:34 AM Bill Van Vlack
wrote:
> James Hupy wrote on Sun, 11 July 2021 23:33
>> The disc brakes require more hydraulic pressure to operate than the drum
>> brakes do. That is why the engineers limited the pressure to the drum
>> brakes. When you have all discs on a coach, there needs to be the same
>> amount of pressure to front and rear, and no delay to the front brakes
> like
>> there is with a combination disc/drum system. Not too complex, really.
>> Jim Hupy
>> Salem, Oregon
>
> That makes sense, but it gets more complex when trying to understand why
> the GMC Motorhome engineers did not do it that way. If I understand Dave
> Lenzi's article correctly, the GMCMH disk/drum coach came with a steel
> combination valve that provided the same amount of pressure to the front and
> rear brakes (after the front brake delay).
> --
> Bill Van Vlack
> '76 Royale; Guemes Island, Washington; Twin bed, full (DS) side bath,
> Brazilian Redwood counter and settee tops,455, 6KW generator; new owner a/o
> mid
> November 2015.
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
|
|
|
|
|
Re: Problem with brass body proportioning valve [message #365380 is a reply to message #365377] |
Mon, 12 July 2021 13:31 |
Bill Van Vlack
Messages: 419 Registered: September 2015 Location: Guemes Island, Washington
Karma: 14
|
Senior Member |
|
|
TR 1 wrote on Mon, 12 July 2021 12:44There's a company in detroit that offers both a disc/drum and disc/disc replacement valve...
I don't know much about it other than seeing it on their site.... Few years ago I bought their dual power steering pulley and it was nicely built, fwtw.....
Disc/disc:
https://www.inlinetube.com/products/pr101
Disc/drum:
https://www.inlinetube.com/products/pr100
Since they call them 'Proportioning Valves', I'd guess they have a proportioning function which we don't want. Also, Dave Lenzi tested several brass valves and all of them had a proportioning function. John L. says the 'HighwayStars' valve is superior to all other brass valves, so if I wanted a new brass valve that duplicated the function of the OEM steel combination valve, I'd buy one of those and disable the proportioning function per the CPP datasheet.
Bill Van Vlack
'76 Royale; Guemes Island, Washington; Twin bed, full (DS) side bath, Brazilian Redwood counter and settee tops,455, 6KW generator; new owner a/o mid November 2015.
|
|
|
Re: Problem with brass body proportioning valve [message #365381 is a reply to message #365380] |
Mon, 12 July 2021 14:34 |
TR 1
Messages: 348 Registered: August 2015 Location: DFW
Karma: -7
|
Senior Member |
|
|
Bill Van Vlack wrote on Mon, 12 July 2021 13:31
Since they call them 'Proportioning Valves', I'd guess they have a proportioning function which we don't want. Also, Dave Lenzi tested several brass valves and all of them had a proportioning function. John L. says the 'HighwayStars' valve is superior to all other brass valves, so if I wanted a new brass valve that duplicated the function of the OEM steel combination valve, I'd buy one of those and disable the proportioning function per the CPP datasheet.
Again, I'm not running one of these valves, nor do I know anything about them... However, they have an online chat feature on the Inlinetube website, and I initaited a chat with someone at the company, and they confirmed the disc/disc" proportioning valve is a 50/50 split front to rear...
The valve is also made in the USA, if that matters to you. So this may be an alternative to buying a valve and modifying it... But again, I don't have or run one... Just throwing this out there as an option someone might like to consider...
Mark S. '73 Painted Desert,
Manny 1 Ton Front End,
Howell Injection,
Leigh Harrison 4bag and Rear Brakes,
Fort Worth, TX
|
|
|
Re: Problem with brass body proportioning valve [message #365386 is a reply to message #365293] |
Mon, 12 July 2021 17:02 |
Greg C.
Messages: 224 Registered: October 2019 Location: Knoxville, TN
Karma: 0
|
Senior Member |
|
|
Since my coach had terrible brakes when I bought it, I can only compare its current braking capability with what it was like at purchase.
I absolutely believe what Mr. Lenzi has to say about it. I have no reservations about his qualifications after speaking with him and purchasing a front hub assembly from him.
That being said, does anyone on the forum have the experience of driving a coach with an aftermarket proportioning valve installed, then modifying it, to provide a before and after comparison?
Or an experienced coach owner who has driven another coach with the unmodified valve?
Greg Crawford
KM4ZCR
Knoxville, TN
"Ruby Sue"
1977 Royale
Rear Bath
403 Engine
American Eagle Wheels
Early Version Alex Sirum Quad bags
|
|
|
Re: Problem with brass body proportioning valve [message #365387 is a reply to message #365293] |
Mon, 12 July 2021 17:12 |
JohnL455
Messages: 4447 Registered: October 2006 Location: Woodstock, IL
Karma: 12
|
Senior Member |
|
|
Greg, consensus is that there was no proportioning from the factory. At this point in time the best bet is to do the simple mod on the GM brass valve to have it basically same as factory but in brass. As reported here and in the article and on the instruction sheet .pdf it’s s simple mod.
Here is a simple analogy to the self energizing effect of drum brakes, and why proportioning is almost always needed with disc/drum (but not on TZE due to weight, length, heavy Onan, propane, water weight aft of rear ‘axle’ ) Imagine walking down a gravel road and holding a shovel handle at your side allowing the shovel to drag behind you at 45 deg. . It creates very little friction. Now do the same but have the shovel at 45 deg in front of you. Yes it digs in much like the forward shoe is pulled against the rotating drum on drum brakes. This is actually a free benefit that discs do not have.
John Lebetski
Woodstock, IL
77 Eleganza II
|
|
|
Re: Problem with brass body proportioning valve [message #365389 is a reply to message #365293] |
Mon, 12 July 2021 17:40 |
Greg C.
Messages: 224 Registered: October 2019 Location: Knoxville, TN
Karma: 0
|
Senior Member |
|
|
Good enough.
I guess I will put this on my to do list, which keeps getting longer. Right now, the remains of my factory dash are in the trash can and I am fabricating a complete new dash, driver to passenger, along with redesigning the A/C ducting and converting to a Jeep A/C control panel.
Thank you for the quick reply.
Greg Crawford
KM4ZCR
Knoxville, TN
"Ruby Sue"
1977 Royale
Rear Bath
403 Engine
American Eagle Wheels
Early Version Alex Sirum Quad bags
|
|
|
|
Re: Problem with brass body proportioning valve [message #365398 is a reply to message #365381] |
Tue, 13 July 2021 10:14 |
Bill Van Vlack
Messages: 419 Registered: September 2015 Location: Guemes Island, Washington
Karma: 14
|
Senior Member |
|
|
TR 1 wrote on Mon, 12 July 2021 14:34
Again, I'm not running one of these valves, nor do I know anything about them... However, they have an online chat feature on the Inlinetube website, and I initaited a chat with someone at the company, and they confirmed the disc/disc" proportioning valve is a 50/50 split front to rear...
The valve is also made in the USA, if that matters to you. So this may be an alternative to buying a valve and modifying it... But again, I don't have or run one... Just throwing this out there as an option someone might like to consider...
Here is my chat with Inlinetube yesterday - the PR101 is their 4 wheel disc brake valve ....
Quote:
Does your PR101 Proportion Valve have a proportioning section?
Jul 12 1:38 PM
Yes it provides a small amount of proportioning.
Michael C · Jul 12 1:41 PM · Appreciate
What does it proportion? (Meaning that the common definition of a proportioning valve is that it sends less pressure to the rear brakes than to the front brakes.)
Jul 12 1:42 PM
Yes, there is a slight bias between the front and the rear.
Michael C · 6:20 AM ·
While I don't understand what '50/50 split front to rear' means (volume?, pressure?), I'm pretty sure that they said that their PR101 reduces pressure to the rear brakes - for what it's worth.
Bill Van Vlack
'76 Royale; Guemes Island, Washington; Twin bed, full (DS) side bath, Brazilian Redwood counter and settee tops,455, 6KW generator; new owner a/o mid November 2015.
|
|
|
|
[GMCnet] Re: Problem with brass body proportioning valve [message #365766 is a reply to message #365765] |
Thu, 29 July 2021 15:30 |
|
Thanks for this news, Tom. I'm so glad that there people constantly
working in the background for our safety.
Jim is to be commended for always having our backs. I hope to be one of
the first adopters in support of his business.
bdub
On Thu, Jul 29, 2021, 2:40 PM Thomas Pryor wrote:
> Well again Thanks to Dave Lenzi, he created the need for more knowledge on
> what happened with the replacement Brass combination valve for our
> coaches.
>
> In a previous life I worked for Kelsey Hayes ABS group as quality "Grunt"
> Foundation brakes knowledge was available to me. So I decided to swim
> upstream and found out that a brass replacement valve for our coaches WAS
> DEVELOPED and put on an engineering drawing. The Code name was PVMH, who
> knew!
> That engineering drawing resurfaced in China and Jim Kanamota has been
> provided with the manufacturer name /contact info. He is negotiating a MOQ
> (Minimum Order Quantity) . I have been assured that all valves will be
> function tested before shipment from the China factory.
>
> MY FINAL THOUGHTS;
> 1. You can modify the PV2 valve to eliminate the pressure limiting to the
> rear brakes. Your option, your risk!
> 2. If you have the original KH86702 Cast Iron Valve.( no rear pressure
> reduction) Flush the brake fluid per the GMC maintenance manual, It may
> look ugly on the outside and perform all required tasks admirably.
> 3. If you ever have to replace the Combination valve make sure it is a
> PVMH.
>
> If you want to follow my investigative /archival information please see:
>
> http://www.gmcmhphotos.com/photos/combination-valves/p68277-gm-valve-autopsy.html
>
> --
> Regards,
>
> Tom Pryor
> 4188 Limerick Dr
> Lake Wales, Fl 33859
> Cell 248 470 9186
>
> 1977 23'B named "CASPER", HARDLY ORIGINAL, (455 EFI) (Pwr. Drive)
> (tailgate) (rear bunk beds)
> (Webasto petrol boiler) (MB Elect fan clutch) (Brake reaction arms) BUT
> STILL A WORK IN PROGRESS!
>
> ReplyForward
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
bdub
bdub.net
|
|
|
|
Re: Problem with brass body proportioning valve [message #365768 is a reply to message #365293] |
Thu, 29 July 2021 18:57 |
JohnL455
Messages: 4447 Registered: October 2006 Location: Woodstock, IL
Karma: 12
|
Senior Member |
|
|
Greg the best bet is to do the simple mod to the genuine GM brass part. To answer your question, proportioning does not begin until a certain pressure is reached, then it is a percentage reduction to counteract the self energizing forward shoe characteristics. But per Dave’s article it was not utilized in the steel assembly line part. GM service parts switched to brass because they knew about the rust issues. But by then GM no longer supported TZE as all that had already been bought out by Cinnabar. Personally knowing of the corrosion issues, I would only want brass and made in USA
John Lebetski
Woodstock, IL
77 Eleganza II
|
|
|
Re: Problem with brass body proportioning valve [message #365769 is a reply to message #365293] |
Thu, 29 July 2021 20:53 |
Tom Katzenberger
Messages: 399 Registered: June 2019 Location: Kingsville, MD
Karma: 4
|
Senior Member |
|
|
Tom,
I purchased the valve from Jim K. and completed the modification. Is this valve and modification not acceptable? I have an original steel valve with 8,000 mile, but it has been in storage for 40 years. Is the steel valve worthy. I have converted to 6 wheel disc system which is sold by Jim at Applied. I am simply trying to make a safer brake system.
Thanks,
Tom K.
Tom & Oki Katzenberger,
Kingsville, Maryland,
1977 23' Birchaven, 455 C.I.D., Micro Level, Howell EBL-EFI Spark Control, Macerator, York Air Compressor, 6 Wheel Disc, Quadra Bag, Onan W/Bovee Ignition
|
|
|
Re: Problem with brass body proportioning valve [message #365770 is a reply to message #365769] |
Thu, 29 July 2021 21:55 |
|
Matt Colie
Messages: 8547 Registered: March 2007 Location: S.E. Michigan
Karma: 7
|
Senior Member |
|
|
Tom Katzenberger wrote on Thu, 29 July 2021 21:53Tom,
I purchased the valve from Jim K. and completed the modification. Is this valve and modification not acceptable? I have an original steel valve with 8,000 mile, but it has been in storage for 40 years. Is the steel valve worthy. I have converted to 6 wheel disc system which is sold by Jim at Applied. I am simply trying to make a safer brake system.
Thanks,
Tom K.
Tom,
Look at the bottom of the brass valve. If it is a PV2, you don't want it. If it is a PV4 it might work with all wheel disk. You really want the PVMH.
Matt
Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL, GMCES
Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum Brakes with Applied Control Arms
SE Michigan - Near DTW - Twixt A2 and Detroit
|
|
|
|
Re: Problem with brass body proportioning valve [message #365805 is a reply to message #365293] |
Sun, 01 August 2021 13:03 |
Larry
Messages: 2875 Registered: January 2004 Location: Menomonie, WI
Karma: 10
|
Senior Member |
|
|
I changed my Combination/Proportioning valve back in 2005 when I did the whole braking system. At that time that "valve" was the old steel one and was quite rusty, so got one from, IIRC, Applied GMC. It was Brass, so I felt I had to check it for the proportioning rubber plug. I did it while installed on the coach. First thing I did was make sure the master cylinder was full and then put the proportioning valve bleed tool for holding to the differential spool valve in place. Then remove the brake line going to the rear wheels, and capped the line off with a inverted flare cap. With fluid trickling out of the combination valve, using a mirror and a flashlight, looked up the valve for the rubber plug and spring. NOT THERE!! So I put it back together and bled the line. Apparently some of the brass ones sold back in the early 2000's did not have that proportioning spring and plug in them. So it is possible that some of you may have the correct brass "combination valve". IMO it is best to check it anyway.
Larry
78 Royale w/500 Caddy
Menomonie, WI.
|
|
|
Re: Problem with brass body proportioning valve [message #365807 is a reply to message #365803] |
Sun, 01 August 2021 13:10 |
Bill Van Vlack
Messages: 419 Registered: September 2015 Location: Guemes Island, Washington
Karma: 14
|
Senior Member |
|
|
Jp Benson wrote on Sat, 31 July 2021 21:19Should I check mine that was purchased from a vendor several years ago? I'm not inclined to open up the hydraulic brake lines.
JP
I did and it did; I don't think anyone's found a brass valve on the market that didn't have the proportioning section. I'm hoping Tom Pryor's efforts change that. I put the steel valve back in.
Bill Van Vlack
'76 Royale; Guemes Island, Washington; Twin bed, full (DS) side bath, Brazilian Redwood counter and settee tops,455, 6KW generator; new owner a/o mid November 2015.
|
|
|
Goto Forum:
Current Time: Sat Sep 28 06:44:54 CDT 2024
Total time taken to generate the page: 0.01047 seconds
|