Home » Public Forums » GMCnet » Termination of oil galley
Termination of oil galley [message #365633] |
Fri, 23 July 2021 07:56 |
Tilerpep
Messages: 404 Registered: June 2013 Location: Raleigh, NC
Karma: 7
|
Senior Member |
|
|
On the rear of the 455 (facing the tranny and flex plate), is the pass side screw in port the end of the pressurized oil galley? On the driver side, the distributor squirter is the end of the pressurized galley, and it is a few inches inside of the rear wall and is covered by a freeze plug type end on the rear wall. The pass side is a screw in.
Here is a pic
http://www.gmcmhphotos.com/photos/back-at-jims/p6969.html
Thanks
1975 Glenbrook, 1978 Royale rear bath
Raleigh, NC
|
|
|
|
[GMCnet] Re: Termination of oil galley [message #365636 is a reply to message #365635] |
Fri, 23 July 2021 09:14 |
James Hupy
Messages: 6806 Registered: May 2010
Karma: -62
|
Senior Member |
|
|
There is a modification that I do on the block where the smaller freeze
plug blocks the end of the oil gallery. I pull that press in plug, throw it
away, and taper thread the hole. Then, I screw in a threaded pipe plug
coated with "the right stuff" or similar.
ALSO, A WORD OF CAUTION HERE. Behind the large freeze plug, there is
another threaded oil gallery plug. If you have had your engine "hot tanked"
you need to be aware that machine shops will pull the existing plugs out of
the oil galleries, and replace them with generic plugs. The plug on a 455
industrial block has a .040" diameter hole bored through it to lube the
distributor gears. Be sure that the plug in your engine has the hole, or
your distributor gears are not long for this world. Same thing applies on
the other end of that gallery. A small hole lubes the timing chain and
gears.
Jim Hupy
Salem, Oregon
On Fri, Jul 23, 2021, 6:54 AM Matt Colie wrote:
> Tilerpep wrote on Fri, 23 July 2021 08:56
>> On the rear of the 455 (facing the tranny and flex plate), is the pass
> side screw in port the end of the pressurized oil galley? On the driver
>> side, the distributor squirter is the end of the pressurized galley, and
> it is a few inches inside of the rear wall and is covered by a freeze plug
>> type end on the rear wall. The pass side is a screw in.
>>
>> Here is a pic
>> http://www.gmcmhphotos.com/photos/back-at-jims/p6969.html
>> Thanks
>
> And the plug in there is a square socket. It is not 1/4 or 3/8 as that
> would be too easy. If anybody needs to borrow a 5/16 square drive tool, I
> made one.
>
> Matt
> --
> Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL,
> GMCES
> Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum
> Brakes with Applied Control Arms
> SE Michigan - Near DTW - Twixt A2 and Detroit
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
|
|
|
[GMCnet] Re: Termination of oil galley [message #365639 is a reply to message #365636] |
Fri, 23 July 2021 11:13 |
jimk
Messages: 6734 Registered: July 2006 Location: Belmont, CA
Karma: 9
|
Senior Member |
|
|
Jim,
That is a great suggestion as we sometimes assume that is done.
Need to remind the machine shop.
On Fri, Jul 23, 2021 at 7:14 AM James Hupy wrote:
> There is a modification that I do on the block where the smaller freeze
> plug blocks the end of the oil gallery. I pull that press in plug, throw it
> away, and taper thread the hole. Then, I screw in a threaded pipe plug
> coated with "the right stuff" or similar.
> ALSO, A WORD OF CAUTION HERE. Behind the large freeze plug, there is
> another threaded oil gallery plug. If you have had your engine "hot tanked"
> you need to be aware that machine shops will pull the existing plugs out of
> the oil galleries, and replace them with generic plugs. The plug on a 455
> industrial block has a .040" diameter hole bored through it to lube the
> distributor gears. Be sure that the plug in your engine has the hole, or
> your distributor gears are not long for this world. Same thing applies on
> the other end of that gallery. A small hole lubes the timing chain and
> gears.
> Jim Hupy
> Salem, Oregon
>
> On Fri, Jul 23, 2021, 6:54 AM Matt Colie wrote:
>
>> Tilerpep wrote on Fri, 23 July 2021 08:56
>>> On the rear of the 455 (facing the tranny and flex plate), is the pass
>> side screw in port the end of the pressurized oil galley? On the driver
>>> side, the distributor squirter is the end of the pressurized galley,
> and
>> it is a few inches inside of the rear wall and is covered by a freeze
> plug
>>> type end on the rear wall. The pass side is a screw in.
>>>
>>> Here is a pic
>>> http://www.gmcmhphotos.com/photos/back-at-jims/p6969.html
>>> Thanks
>>
>> And the plug in there is a square socket. It is not 1/4 or 3/8 as that
>> would be too easy. If anybody needs to borrow a 5/16 square drive tool,
> I
>> made one.
>>
>> Matt
>> --
>> Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL,
>> GMCES
>> Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum
>> Brakes with Applied Control Arms
>> SE Michigan - Near DTW - Twixt A2 and Detroit
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
>
--
Jim Kanomata ASE
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.gmcrvparts.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502
|
|
|
Goto Forum:
Current Time: Sun Sep 29 00:52:27 CDT 2024
Total time taken to generate the page: 0.00721 seconds
|