Home » Public Forums » GMCnet » DigiPanel Accuracy (An “in stream” temperature probe)
| DigiPanel Accuracy [message #360356] |
Sun, 29 November 2020 10:03  |
 |
SteveW
Messages: 538
Registered: June 2005
Location: Southern California - Ora...
Karma: 1
|
Senior Member |
|
|
Greetings !!
I’m messing around with my cooling system. New 195 thermostat, Mercedes fan system, factory temperature gauge (with proper TS-6469 sender), and a DigiPanel.
I’m skeptical of engine temperature as reported by my DigiPanel. The temp sender for the DigiPanel is a small copper flange that is squeezed into the thermostat housing. Previously - I could see temperatures as low as 130 while my factory gauge still displayed 180-190. I discovered that this temperature probe was directly subject to the significant air stream from the radiator fan... I suspected that said air stream was dramatically cooling the thermostat housing - or at least the probe - and reporting temperature lower than the actual coolant. Convection. I’ve insulated the probe with some high temp hose insulation. It seems improved - but I have not yet thoroughly tested it.
The same configuration exists for the transmission temperature probe. A small copper flange wedged in with one of the transmission pan bolts. It’s in the airstream too !!
Any comments on the DigiPanel’s accuracy with such temperature probes ?? Anyone replace these probes with something in the actual liquid stream(s) ??
Thanks in advance for any insights.
Steve W
1973. 23. Yellow
Southern California
Steve W
1973 : 23'
Southern California
|
|
|
|
| Re: DigiPanel Accuracy [message #360363 is a reply to message #360356] |
Sun, 29 November 2020 10:54  |
 |
Matt Colie
Messages: 8547
Registered: March 2007
Location: S.E. Michigan
Karma: 7
|
Senior Member |
|
|
Steve,
I noted this same issue.
Indeed, the one on the thermostat housing was significant, but when I relocated the measurement point to behind the housing and put an air deflector around it, it came right in line.
When received my Digipanel, it came with a small piece of insulation that was for one of the temperature points as installed. So, after I noted the same irregularity, I made sure to do similar with all three temperature measurement points. I doesn't take much to make them all, more or less, agree with the infrared. There will always be some disagreement, but that is the nature (perverse as it may be) of instrumentation.
The actual temperatures any place in the system are simply not that important. You should be able to see important variations with enough warning to deal with them, that is all you can ever hope for.
A map of the cooling system temperatures was in my plans, but we had snow and the have spread salt (aka fender solvent) on the roads. That means Chaumière get to stay on the lot until the rain clears it all away.
Matt
Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL, GMCES
Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum Brakes with Applied Control Arms
SE Michigan - Near DTW - Twixt A2 and Detroit
|
|
|
|
| Re: [GMCnet] DigiPanel Accuracy [message #360373 is a reply to message #360363] |
Sun, 29 November 2020 18:30 |
jimk
Messages: 6734
Registered: July 2006
Location: Belmont, CA
Karma: 9
|
Senior Member |
|
|
I have been told that the boit is short, will not sense as well as the
longer.
There are over thousand units out there and have saved lot of engines.
On Sun, Nov 29, 2020 at 8:55 AM Matt Colie via Gmclist <
gmclist@list.gmcnet.org> wrote:
> Steve,
>
> I noted this same issue.
> Indeed, the one on the thermostat housing was significant, but when I
> relocated the measurement point to behind the housing and put an air
> deflector
> around it, it came right in line.
>
> When received my Digipanel, it came with a small piece of insulation that
> was for one of the temperature points as installed. So, after I noted the
> same irregularity, I made sure to do similar with all three temperature
> measurement points. I doesn't take much to make them all, more or less,
> agree
> with the infrared. There will always be some disagreement, but that is
> the nature (perverse as it may be) of instrumentation.
>
> The actual temperatures any place in the system are simply not that
> important. You should be able to see important variations with enough
> warning to
> deal with them, that is all you can ever hope for.
>
> A map of the cooling system temperatures was in my plans, but we had snow
> and the have spread salt (aka fender solvent) on the roads. That means
> Chaumière get to stay on the lot until the rain clears it all away.
>
> Matt
> --
> Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL,
> GMCES
> Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum
> Brakes with Applied Control Arms
> SE Michigan - Near DTW - Twixt A2 and Detroit
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
Jim Kanomata
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.gmcrvparts.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502
|
|
|
|
| Re: [GMCnet] DigiPanel Accuracy [message #360377 is a reply to message #360373] |
Sun, 29 November 2020 19:50 |
|
|
Mike
Hold Billie tight for us. We're praying she heals quickly.
Billy
On Sun, Nov 29, 2020 at 7:36 PM Mike Kelley via Gmclist <
gmclist@list.gmcnet.org> wrote:
> Jim K.:
> I did not take this discussion as detrimental to the unit our you - just
> valuable info the technically inclined. One of my
> Digi-panels indicates hotter temps than my engine gauge, but having gotten
> used to how it reads - I still know when to feel safe versus alarmed!
> Mike/the Corvair a holic
>
> Sent from my iPhone
>
>> On Nov 29, 2020, at 6:30 PM, Jim Kanomata via Gmclist gmclist@list.gmcnet.org> wrote:
>>
>> I have been told that the boit is short, will not sense as well as the
>> longer.
>> There are over thousand units out there and have saved lot of engines.
>>
>> On Sun, Nov 29, 2020 at 8:55 AM Matt Colie via Gmclist > gmclist@list.gmcnet.org> wrote:
>>
>>> Steve,
>>>
>>> I noted this same issue.
>>> Indeed, the one on the thermostat housing was significant, but when I
>>> relocated the measurement point to behind the housing and put an air
>>> deflector
>>> around it, it came right in line.
>>>
>>> When received my Digipanel, it came with a small piece of insulation
> that
>>> was for one of the temperature points as installed. So, after I noted
> the
>>> same irregularity, I made sure to do similar with all three temperature
>>> measurement points. I doesn't take much to make them all, more or less,
>>> agree
>>> with the infrared. There will always be some disagreement, but that is
>>> the nature (perverse as it may be) of instrumentation.
>>>
>>> The actual temperatures any place in the system are simply not that
>>> important. You should be able to see important variations with enough
>>> warning to
>>> deal with them, that is all you can ever hope for.
>>>
>>> A map of the cooling system temperatures was in my plans, but we had
> snow
>>> and the have spread salt (aka fender solvent) on the roads. That means
>>> Chaumière get to stay on the lot until the rain clears it all away.
>>>
>>> Matt
>>> --
>>> Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL,
>>> GMCES
>>> Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum
>>> Brakes with Applied Control Arms
>>> SE Michigan - Near DTW - Twixt A2 and Detroit
>>>
>>> _______________________________________________
>>> GMCnet mailing list
>>> Unsubscribe or Change List Options:
>>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>>
>>
>>
>> --
>> Jim Kanomata
>> Applied/GMC, Newark,CA
>> jimk@appliedairfilters.com
>> http://www.gmcrvparts.com
>> 1-800-752-7502
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
bdub
bdub.net
|
|
|
|
| Re: [GMCnet] DigiPanel Accuracy [message #360378 is a reply to message #360373] |
Sun, 29 November 2020 19:56 |
Mike Kelley
Messages: 467
Registered: February 2017
Karma: -2
|
Senior Member |
|
|
👍
Thanks Man!
Sent from my iPhone
> On Nov 29, 2020, at 7:50 PM, Billy Massey via Gmclist wrote:
>
> Mike
> Hold Billie tight for us. We're praying she heals quickly.
>
> Billy
>
> On Sun, Nov 29, 2020 at 7:36 PM Mike Kelley via Gmclist gmclist@list.gmcnet.org> wrote:
>
>> Jim K.:
>> I did not take this discussion as detrimental to the unit our you - just
>> valuable info the technically inclined. One of my
>> Digi-panels indicates hotter temps than my engine gauge, but having gotten
>> used to how it reads - I still know when to feel safe versus alarmed!
>> Mike/the Corvair a holic
>>
>> Sent from my iPhone
>>
>>> On Nov 29, 2020, at 6:30 PM, Jim Kanomata via Gmclist > gmclist@list.gmcnet.org> wrote:
>>>
>>> I have been told that the boit is short, will not sense as well as the
>>> longer.
>>> There are over thousand units out there and have saved lot of engines.
>>>
>>> On Sun, Nov 29, 2020 at 8:55 AM Matt Colie via Gmclist >> gmclist@list.gmcnet.org> wrote:
>>>
>>>> Steve,
>>>>
>>>> I noted this same issue.
>>>> Indeed, the one on the thermostat housing was significant, but when I
>>>> relocated the measurement point to behind the housing and put an air
>>>> deflector
>>>> around it, it came right in line.
>>>>
>>>> When received my Digipanel, it came with a small piece of insulation
>> that
>>>> was for one of the temperature points as installed. So, after I noted
>> the
>>>> same irregularity, I made sure to do similar with all three temperature
>>>> measurement points. I doesn't take much to make them all, more or less,
>>>> agree
>>>> with the infrared. There will always be some disagreement, but that is
>>>> the nature (perverse as it may be) of instrumentation.
>>>>
>>>> The actual temperatures any place in the system are simply not that
>>>> important. You should be able to see important variations with enough
>>>> warning to
>>>> deal with them, that is all you can ever hope for.
>>>>
>>>> A map of the cooling system temperatures was in my plans, but we had
>> snow
>>>> and the have spread salt (aka fender solvent) on the roads. That means
>>>> Chaumière get to stay on the lot until the rain clears it all away.
>>>>
>>>> Matt
>>>> --
>>>> Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL,
>>>> GMCES
>>>> Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum
>>>> Brakes with Applied Control Arms
>>>> SE Michigan - Near DTW - Twixt A2 and Detroit
>>>>
>>>> _______________________________________________
>>>> GMCnet mailing list
>>>> Unsubscribe or Change List Options:
>>>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>>>
>>>
>>>
>>> --
>>> Jim Kanomata
>>> Applied/GMC, Newark,CA
>>> jimk@appliedairfilters.com
>>> http://www.gmcrvparts.com
>>> 1-800-752-7502
>>> _______________________________________________
>>> GMCnet mailing list
>>> Unsubscribe or Change List Options:
>>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
|
| Re: [GMCnet] DigiPanel Accuracy [message #360379 is a reply to message #360373] |
Sun, 29 November 2020 19:35 |
Mike Kelley
Messages: 467
Registered: February 2017
Karma: -2
|
Senior Member |
|
|
Jim K.:
I did not take this discussion as detrimental to the unit our you - just valuable info the technically inclined. One of my
Digi-panels indicates hotter temps than my engine gauge, but having gotten used to how it reads - I still know when to feel safe versus alarmed!
Mike/the Corvair a holic
Sent from my iPhone
> On Nov 29, 2020, at 6:30 PM, Jim Kanomata via Gmclist wrote:
>
> I have been told that the boit is short, will not sense as well as the
> longer.
> There are over thousand units out there and have saved lot of engines.
>
> On Sun, Nov 29, 2020 at 8:55 AM Matt Colie via Gmclist gmclist@list.gmcnet.org> wrote:
>
>> Steve,
>>
>> I noted this same issue.
>> Indeed, the one on the thermostat housing was significant, but when I
>> relocated the measurement point to behind the housing and put an air
>> deflector
>> around it, it came right in line.
>>
>> When received my Digipanel, it came with a small piece of insulation that
>> was for one of the temperature points as installed. So, after I noted the
>> same irregularity, I made sure to do similar with all three temperature
>> measurement points. I doesn't take much to make them all, more or less,
>> agree
>> with the infrared. There will always be some disagreement, but that is
>> the nature (perverse as it may be) of instrumentation.
>>
>> The actual temperatures any place in the system are simply not that
>> important. You should be able to see important variations with enough
>> warning to
>> deal with them, that is all you can ever hope for.
>>
>> A map of the cooling system temperatures was in my plans, but we had snow
>> and the have spread salt (aka fender solvent) on the roads. That means
>> Chaumière get to stay on the lot until the rain clears it all away.
>>
>> Matt
>> --
>> Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL,
>> GMCES
>> Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum
>> Brakes with Applied Control Arms
>> SE Michigan - Near DTW - Twixt A2 and Detroit
>>
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>
>
>
> --
> Jim Kanomata
> Applied/GMC, Newark,CA
> jimk@appliedairfilters.com
> http://www.gmcrvparts.com
> 1-800-752-7502
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
|
|
|
| Re: [GMCnet] DigiPanel Accuracy [message #360383 is a reply to message #360382] |
Sun, 29 November 2020 20:36 |
Mike Kelley
Messages: 467
Registered: February 2017
Karma: -2
|
Senior Member |
|
|
Mac:
She tripped while on an R V Volunteer church remodel project in Lufkin, Tx. - hit back of her head on concrete floor - very hard! In hospital in Tyler, Tx. for 2 brain bleeds and cracked skull! Neurosurgeon did his magic this am and she is doing better - still not out of the woods but so far her body is responding well and mending is
happening! Hoping to be out of ICU in 2 to 3 days and out of hospital in 7 to 10 days.
This hospital and dr’s and staff have been fantastic!
Mike Kelley
Sent from my iPhone
> On Nov 29, 2020, at 8:14 PM, D C _Mac_ Macdonald via Gmclist wrote:
>
> What's up with Billie????
>
> D C "Mac" Macdonald
> Amateur Radio K2GKK
> Since 30 November '53
> USAF and FAA, Retired
> Member GMCMI & Classics
> Oklahoma City, OK
> "The Money Pit"
> TZE166V101966
> '76 ex-Palm Beach
> k2gkk + hotmail dot com
>
> ________________________________
> From: Gmclist on behalf of Billy Massey via Gmclist
> Sent: Sunday, November 29, 2020 19:50
> To: GMCnet
> Cc: Billy Massey
> Subject: Re: [GMCnet] DigiPanel Accuracy
>
> Mike
> Hold Billie tight for us. We're praying she heals quickly.
>
> Billy
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
|
Goto Forum:
Current Time: Fri Sep 20 00:29:03 CDT 2024
Total time taken to generate the page: 0.00978 seconds
|
GMCforum
Search
Help
Register
Login
Home
