Engine front mount bolts [message #359345] |
Sat, 10 October 2020 00:28 |
|
Husker92592
Messages: 137 Registered: August 2013 Location: Temecula ca
Karma: -4
|
Senior Member |
|
|
Does anyone know the bolt size that mounts the front engine mount to the crossmember?
Thanks
Grant
1974 GMC Sequoia 26'
|
|
|
|
|
|
Re: Engine front mount bolts [message #359390 is a reply to message #359345] |
Sat, 10 October 2020 21:04 |
lqqkatjon
Messages: 2324 Registered: October 2010 Location: St. Cloud, MN
Karma: 5
|
Senior Member |
|
|
Exactly what Matt said. They are supposed
To be studs out of the motor mount. And you remove 2 Nuts.
However. 50/50. I have pulled out a few bolts too. If someone else has had your engine out,
They
Might have out a bolt in there.
A stud
And nut is much better when taking engine in and out and wanting things to aline.
Jon Roche
75 palm beach
EBL EFI, manny headers, Micro Level, rebuilt most of coach now.
St. Cloud, MN
http://lqqkatjon.blogspot.com/
|
|
|
Re: Engine front mount bolts [message #359391 is a reply to message #359345] |
Sat, 10 October 2020 21:07 |
Rick Staples
Messages: 126 Registered: May 2014 Location: Johnstown, Colorado, USA
Karma: -1
|
Senior Member |
|
|
The studs (not bolts) you need, GM part #390403, are special studs with a large shoulder between the two threaded ends. You might be able to jury-rig something with studs and a stack of washers, but I'd recommend checking with one of the Jims, or Cinnabar, or someone with a parts coach. Don't know, but maybe a Toronado would have the same parts. (My old 1980 Chilton's appears to show the same front mount on the Toronado).
HTH
Rick Staples
Rick Staples, '75 Eleganza, Johnstown, CO
"Advice is a dangerous gift, even from the Wise to the Wise, and all paths may run ill." -Tolkien
|
|
|
Re: [GMCnet] Engine front mount bolts [message #359393 is a reply to message #359351] |
Sat, 10 October 2020 21:16 |
jimk
Messages: 6734 Registered: July 2006 Location: Belmont, CA
Karma: 9
|
Senior Member |
|
|
Grant,
We can supply a used stud and nut.
On Sat, Oct 10, 2020 at 7:54 AM Matt Colie via Gmclist <
gmclist@list.gmcnet.org> wrote:
> Grant,
>
> The front mount fastens to the cross member with 1/2 studs and nuts. I
> had the studs come out of my front mount, and I really did try to put them
> back with the engine on the frame. I gave up. I separated the studs from
> nuts, jacked up the engine and put the studs back in the front mount and
> set it down again. Then it was easy to get the nuts started.
>
> Matt
> --
> Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL,
> GMCES
> Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum
> Brakes with Applied Control Arms
> SE Michigan - Near DTW - Twixt A2 and Detroit
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
Jim Kanomata
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.gmcrvparts.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502
|
|
|
|
Re: [GMCnet] Engine front mount bolts [message #359440 is a reply to message #359439] |
Mon, 12 October 2020 23:18 |
jimk
Messages: 6734 Registered: July 2006 Location: Belmont, CA
Karma: 9
|
Senior Member |
|
|
I never have used it on the front center, I'll try it tomorrow.
On Mon, Oct 12, 2020 at 9:05 PM Grant Schaffer via Gmclist <
gmclist@list.gmcnet.org> wrote:
> Yes you are correct there is a bolt / stud what ever you want to call it
> today and a nut that hold the rubber mount on to the mounting plate the
> mounting plate or " front motor mount" is attached to the front of the
> engine right under the water pump. now can anyone tell how one will secure
> the
> mount and the rubber isolator that is attached to the front motor mount to
> the frame cross over? there are two bolts that screw into a metal plate
> that is held in place by the rubber isolator.
>
> New Front Motor Mounts - GMC Motorhome at JIM K site, WESTAR EM5450 or DEA
> / MARMON RIDE CONTROL A5034 there are 4 holes, the two outside get a stud
> and a nut and possible a couple washers and the two internal that mount
> from the inside of the front crossover though the crossover to these
> threaded
> holes on the rubber " front motor mount" threaded holes get what ? 5/16" -
> 1" ? 3/8" 1? 1/2" -1"?
> --
> 1974 GMC Sequoia 26'
>
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
Jim Kanomata
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.gmcrvparts.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502
|
|
|