Home » Public Forums » GMCnet » 1 Ton Front Suspension Conversion (Reviews)
1 Ton Front Suspension Conversion [message #358633] |
Mon, 14 September 2020 17:55 |
Tom Katzenberger
Messages: 399 Registered: June 2019 Location: Kingsville, MD
Karma: 4
|
Senior Member |
|
|
Ladies and Gentlemen,
The one ton front suspension conversion has been out for quite a while. I just want to check the satisfaction rate, good bad and ugly.
I am very interested and while I coach cut in half, it may be the best time to install such an item.
I am also looking at the Holley Sniper System, Serpentine Belt system, and All disk brakes.
Thanks in advance for any input.
Tom & Oki Katzenberger
Tom & Oki Katzenberger,
Kingsville, Maryland,
1977 23' Birchaven, 455 C.I.D., Micro Level, Howell EBL-EFI Spark Control, Macerator, York Air Compressor, 6 Wheel Disc, Quadra Bag, Onan W/Bovee Ignition
|
|
|
Re: [GMCnet] 1 Ton Front Suspension Conversion [message #358640 is a reply to message #358633] |
Mon, 14 September 2020 18:44 |
Ken Henderson
Messages: 8726 Registered: March 2004 Location: Americus, GA
Karma: 9
|
Senior Member |
|
|
dTom,
I didn't see this note until I'd sent the one about the body parts.
I've had the 1-ton front suspension since Manny's first production run. I
like it a lot. If there's any torque steer, I'm not sensitive enough to
notice it. Now Dunahugh, if you ask him when you call, will tell you it's
AWFUL -- but then he's a skilled race car driver
Serpentine belts are another of my favorites. It was mandatory for me to
put them on my Cad500 before ever installing it and they've (I use two)
never given me a moment's trouble -- far more than I could ever say about
the V-belts that came on the 455. I put serpentines on the 455 too, but
don't have any details and would probably do it differently anyway. After
doing the Cad, I'm convince I could, with access to a 455, design a simple
2-serp system for it too.
Ken H.
Americus, GA
'76 X-Birchaven w/Cad500/Howell EFI & EBL,
Manny Brakes & 1-Ton, Troy-Bilt APU, etc., etc., etc.
www.gmcwipersetc.com
On Mon, Sep 14, 2020 at 6:56 PM tomkatz3--- via Gmclist <
gmclist@list.gmcnet.org> wrote:
> Ladies and Gentlemen,
>
> The one ton front suspension conversion has been out for quite a while. I
> just want to check the satisfaction rate, good bad and ugly.
>
> I am very interested and while I coach cut in half, it may be the best
> time to install such an item.
>
> I am also looking at the Holley Sniper System, Serpentine Belt system, and
> All disk brakes.
>
> Thanks in advance for any input.
>
> Tom & Oki Katzenberger
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Ken Henderson
Americus, GA
www.gmcwipersetc.com
Large Wiring Diagrams
76 X-Birchaven
76 X-Palm Beach
|
|
|
Re: 1 Ton Front Suspension Conversion [message #358643 is a reply to message #358633] |
Mon, 14 September 2020 19:07 |
Tom Katzenberger
Messages: 399 Registered: June 2019 Location: Kingsville, MD
Karma: 4
|
Senior Member |
|
|
Ken, Again thank you. Your input is very heavily weighted and I appreciate it. I will look to acquire both.
Thanks again,
Tom
Tom & Oki Katzenberger,
Kingsville, Maryland,
1977 23' Birchaven, 455 C.I.D., Micro Level, Howell EBL-EFI Spark Control, Macerator, York Air Compressor, 6 Wheel Disc, Quadra Bag, Onan W/Bovee Ignition
|
|
|
|
|
|
Re: [GMCnet] 1 Ton Front Suspension Conversion [message #358664 is a reply to message #358653] |
Tue, 15 September 2020 10:20 |
jimk
Messages: 6734 Registered: July 2006 Location: Belmont, CA
Karma: 9
|
Senior Member |
|
|
I your not a hands on guy , going to one ton is not suggested as there are
parts you need to know where they can be acquired.
We sell the Kit, but I can tell you most of the GMC shops are not
familiar enough and call me for info.
It cost lees to do the front end as the parts come reassembled with new
parts.
Larry W is correct, if you do the original properly it will be
On Mon, Sep 14, 2020 at 8:02 PM Larry via Gmclist
wrote:
> It should be noted that a properly installed and/or serviced OEM front end
> is more than capable of lasting beyond your lifetime. A set of Lenzi
> rebuilt knuckles with grease zirks, lubricated every 25K or so miles is as
> about trouble free as you could expect from our front ends. Just keep an
> eye on the CV boots and change when they show sign of cracking will keep
> you in axles for the duration. JMHO
> --
> Larry
> 78 Royale w/500 Caddy
> Menomonie, WI.
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
Jim Kanomata
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.gmcrvparts.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502
|
|
|
Re: [GMCnet] 1 Ton Front Suspension Conversion [message #358671 is a reply to message #358664] |
Tue, 15 September 2020 14:34 |
James Hupy
Messages: 6806 Registered: May 2010
Karma: -62
|
Senior Member |
|
|
I know Bill Hubler quite well, After a trip down the BAJA his GMC several
years ago where he attempted to turn the coach into a driveway and the
front hub fell into the sharp ditch, and subsequent adventures getting
parts to repair the damage, he returned to Idaho and decided to see if he
could adapt some more robust parts to the front end of the GMC. The 1 ton
is a result of that effort. After making them ones and twos at a time, he
decided that it took up too much of his time, and he and Manny Traveo made
an agreement for Manny to take over making the Hubler 1 ton front end. So,
Manny invested in a whole batch of GM pieces and produced the present
version of the 1 ton front end. It is robust and has commonly available
parts. Needs no special tools to disassemble. Has much larger brake rotors
and front disc brakes. The whole hub, knuckle and spacer is right off of GM
vehicles, but, the spacer, which is identical in dimensions to the GM
piece, is aluminum instead of Cast Iron. About 1/2 of the weight of the
stock GM spacer. Does it match up to a formula 1 race car suspension, Nope.
It does not have to. Will it last a good long time, and be easier to fix
when and/or if it fails on the road? Yes. Is it cheaper than rebuilding an
entire GMC stock front end? Sure is. Is it better? Opinions vary on that.
Jim Hupy
Salem, Oregon
On Tue, Sep 15, 2020 at 8:21 AM Jim Kanomata via Gmclist <
gmclist@list.gmcnet.org> wrote:
> I your not a hands on guy , going to one ton is not suggested as there are
> parts you need to know where they can be acquired.
> We sell the Kit, but I can tell you most of the GMC shops are not
> familiar enough and call me for info.
> It cost lees to do the front end as the parts come reassembled with new
> parts.
> Larry W is correct, if you do the original properly it will be
>
>
> On Mon, Sep 14, 2020 at 8:02 PM Larry via Gmclist >
> wrote:
>
>> It should be noted that a properly installed and/or serviced OEM front
> end
>> is more than capable of lasting beyond your lifetime. A set of Lenzi
>> rebuilt knuckles with grease zirks, lubricated every 25K or so miles is
> as
>> about trouble free as you could expect from our front ends. Just keep an
>> eye on the CV boots and change when they show sign of cracking will keep
>> you in axles for the duration. JMHO
>> --
>> Larry
>> 78 Royale w/500 Caddy
>> Menomonie, WI.
>>
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>
>
>
> --
> Jim Kanomata
> Applied/GMC, Newark,CA
> jimk@appliedairfilters.com
> http://www.gmcrvparts.com
> 1-800-752-7502
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
Re: 1 Ton Front Suspension Conversion [message #358674 is a reply to message #358633] |
Tue, 15 September 2020 16:49 |
Scott Nutter
Messages: 782 Registered: January 2015 Location: Houston/San Diego
Karma: 4
|
Senior Member |
|
|
Tom,
I like your list of upgrades you are thinking of doing. As you can see, there are strong opinions on both sides of the issues. Which to me means that either way you decide to go will be good.
1 ton front end...I went with Dave Lenzi’s knuckles and 80mm brakes using 5.1 dot brake fluid. For me they are great. But if anything brakes, I would put on the 1 ton front end. But I would like to drive one first just to see the difference, if any.
Holley sniper EFI. I went with the MSD Atomic. But I think the new Holley sniper now has a better handheld and electronic gauge setup. If I was to do now, I would also probably go with the Holley sniper. But I am happy with my MSD. But I think the absolute best is the Howell EFI with timing controller. If only I had the money....
Serpentine belt system. I don’t have it, but I will one of these days!!
Rear Discs brakes. This is another one that you will probably have strong opinions on both sides. I drool when I think of having one of Dave Lenzi’s rear disc conversions!! Soon!!
Great list, and good luck.
Scott
Scott Nutter
1978 Royale Center Kitchen, Patterson 455, switch pitch tranny, 3.21 final drive, Quad bags, Dave Lenzi super duty mid axle disc brakes, tankless water heater, everything Lenzi. Alex Ferrera installed MSD Atomic EFI
Houston, Texas
|
|
|
Re: 1 Ton Front Suspension Conversion [message #358677 is a reply to message #358633] |
Tue, 15 September 2020 18:02 |
Tom Katzenberger
Messages: 399 Registered: June 2019 Location: Kingsville, MD
Karma: 4
|
Senior Member |
|
|
Thank you to all. I do have a lot of head scratching to do.
Tom & Oki Katzenberger,
Kingsville, Maryland,
1977 23' Birchaven, 455 C.I.D., Micro Level, Howell EBL-EFI Spark Control, Macerator, York Air Compressor, 6 Wheel Disc, Quadra Bag, Onan W/Bovee Ignition
|
|
|
Re: [GMCnet] 1 Ton Front Suspension Conversion [message #358680 is a reply to message #358677] |
Tue, 15 September 2020 21:22 |
|
ljdavick
Messages: 3548 Registered: March 2007 Location: Fremont, CA
Karma: -3
|
Senior Member |
|
|
I’ve had my original front end rebuilt and I’m underwhelmed. If the 1-ton offers more caster, then I’d go with it, in retrospect. My coach still does not follow a straight line. Of course I have steel wheels and Firestone transforce tires but I was hoping after rebuilding the front end it would handle markedly better.
The new shocks made a big difference in the ride, that I never knew I needed! I’m hoping when I finally get some excitement back for the ol’ girl and put some real miles on it I’ll warm up to how it drives.
Larry Davick
1976 Palm Beach
Fremont, Ca.
Sent from my iPad
> On Sep 15, 2020, at 4:02 PM, tomkatz3--- via Gmclist wrote:
>
> Thank you to all. I do have a lot of head scratching to do.
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Larry Davick
A Mystery Machine
1976(ish) Palm Beach
Fremont, Ca
Howell EFI + EBL + Electronic Dizzy
|
|
|
|
Re: 1 Ton Front Suspension Conversion [message #358685 is a reply to message #358633] |
Wed, 16 September 2020 06:54 |
|
RF_Burns
Messages: 2277 Registered: June 2008 Location: S. Ontario, Canada
Karma: 3
|
Senior Member |
|
|
Better front brakes is my everyday benefit from the 1-ton.
The 1-ton rotors are 12.5" diameter rather than 11", so there is more swept area on the rotor for every revolution of the wheel. The larger rotor also gives the brakes more mechanical advantage against wheel rotation resulting in more braking force.
Add in the slightly larger caliper piston, it all adds up to significant braking improvement.
Has anyone calculated the increased braking force with the 1-ton over OEM? Albert Branscombe?
Bruce Hislop
ON Canada
77PB, 455 Dick P. rebuilt, DynamicEFI EBL EFI & ESC. 1 ton front end
http://www.gmcmhphotos.com/photos/showphoto.php?photo=29001
My Staff says I never listen to them, or something like that
|
|
|
Goto Forum:
Current Time: Thu Sep 19 17:33:07 CDT 2024
Total time taken to generate the page: 0.00931 seconds
|