Home » Public Forums » GMCnet » Setting on the skids
Setting on the skids [message #357159] |
Fri, 24 July 2020 14:45 |
Greg C.
Messages: 224 Registered: October 2019 Location: Knoxville, TN
Karma:
|
Senior Member |
|
|
Okay, well, I've done it now. I've had my new coach home for three weeks now. I've replaced the driver's side manifold and gasket, (major shout out to Jim Hupy for the cordless impact suggestion, all bolts out with no breakage! And the 1/8" hole drilled above the middle bolt! ) and am now replacing the old toilet and cleaning up.
Today I decided to try out the auto level system and see how it worked.
The PO told me that the auto leveling system works just fine, but that the compressor would not shut off. So either he or a PO before him had installed shut off valves at the quad bags. He said that he would run the compressor and get the coach where he wanted it, and then shut off the air valves to hold it.
Well, I started up the coach and put the switch in Travel, and went outside and opened the shut off valves. Went back inside with a spray bottle of soapy water and identified three leaks, two at the solenoids and one at the fitting exiting the head of the factory compressor. Went back outside and found a leak at the driver's side auto leveling valve.
I noticed the coach was getting lower, and before long it was sitting on the skid bars that some PO had installed to protect the dump valve.
I tried Left Raise, Right Raise, Travel, etc, but the coach won't lift even though the compressor is running. There is a schrader valve on the bottom of the little air tank next to the compressor. I have a small 110v portable compressor that maxes out around 90 psi, so I hooked that to the schrader valve on the tank, no joy.
So, my coach is in the driveway, currently unmoveable, which stinks because I just went today and got new tags for it so I could drive it.
Can anyone offer some sage advice on how to get it back up to travel height?
Thank you.
Greg Crawford
KM4ZCR
Knoxville, TN
"Ruby Sue"
1977 Royale
Rear Bath
403 Engine
American Eagle Wheels
Early Version Alex Sirum Quad bags
|
|
|
|
|
Setting on the skids
By: Greg C. on Fri, 24 July 2020 14:45
|
|
|
Re: [GMCnet] Setting on the skids
By: Keith V on Fri, 24 July 2020 15:13
|
|
|
Re: Setting on the skids
By: Greg C. on Fri, 24 July 2020 15:46
|
|
|
Re: [GMCnet] Setting on the skids
|
|
|
Re: [GMCnet] Setting on the skids
|
|
|
Re: [GMCnet] Setting on the skids
|
|
|
Re: Setting on the skids
|
|
|
Re: Setting on the skids
|
|
|
Re: [GMCnet] Setting on the skids
By: G?Rs66 on Sun, 26 July 2020 09:34
|
|
|
Re: [GMCnet] Setting on the skids
|
|
|
Re: [GMCnet] Setting on the skids
By: G?Rs66 on Sun, 26 July 2020 12:08
|
|
|
Re: [GMCnet] Setting on the skids
|
|
|
Re: Setting on the skids
By: Greg C. on Sat, 25 July 2020 09:12
|
|
|
Re: Setting on the skids
|
|
|
Re: [GMCnet] Setting on the skids
|
|
|
Re: [GMCnet] Setting on the skids
By: Keith V on Sat, 25 July 2020 11:38
|
|
|
Re: [GMCnet] Setting on the skids
|
|
|
Re: Setting on the skids
By: Greg C. on Sat, 25 July 2020 20:12
|
|
|
Re: Setting on the skids
By: Greg C. on Wed, 29 July 2020 19:05
|
|
|
Re: [GMCnet] Setting on the skids
|
|
|
Re: Setting on the skids
By: Greg C. on Thu, 30 July 2020 08:12
|
|
|
Re: [GMCnet] Setting on the skids
By: sgltrac on Thu, 30 July 2020 10:28
|
|
|
Re: [GMCnet] Setting on the skids
|
|
|
Re: [GMCnet] Setting on the skids
|
|
|
Re: Setting on the skids
By: Greg C. on Thu, 30 July 2020 08:15
|
|
|
Re: [GMCnet] Setting on the skids
|
|
|
Re: Setting on the skids
By: Greg C. on Thu, 30 July 2020 12:59
|
|
|
Re: [GMCnet] Setting on the skids
|
Goto Forum:
Current Time: Fri Sep 20 12:33:25 CDT 2024
Total time taken to generate the page: 0.01204 seconds
|