[GMCnet] Onan board connections [message #357063] |
Tue, 21 July 2020 15:12 |
stu@97381.com, Emery
Messages: 232 Registered: June 2020
Karma: 2
|
Senior Member |
|
|
I was working in my Onan and removed the wires from the board. I wasn’t too concerned because the small numbers inside the Molex connector would guide me.
The wires are marked with numbers for the terminals but my wires had darkened and discolored so I couldn’t read most of them. But inside the plug are very small numbers that correspond to the terminals.
I hooked the wires back up but I had a long one left that went to the number 4 terminal. There was a number four terminal at the top of the board that was bent over so it would not be used. This was a long wire so I knew that it went to the bottom of the board. I was left with one unused terminal between number nine and number eleven. But it was labeled with a 1 besides it. Where did the number four wire go?
I finally called Jim Miller and he checked a board in his shop and verified that the wire number 4 was plugged into the terminal Marked with a 1.
So if anyone has to figure out the connections by the little numbers inside the Molex plug they are all correct EXCEPT wire 4.
Emery Stora
77 Kingsley
Frederick CO
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
Re: [GMCnet] Onan board connections [message #357065 is a reply to message #357063] |
Tue, 21 July 2020 19:11 |
jimk
Messages: 6734 Registered: July 2006 Location: Belmont, CA
Karma: 9
|
Senior Member |
|
|
Emery,
I will send over all so you can Finger it out.
On Tue, Jul 21, 2020 at 1:13 PM Emery Stora via Gmclist <
gmclist@list.gmcnet.org> wrote:
> I was working in my Onan and removed the wires from the board. I wasn’t
> too concerned because the small numbers inside the Molex connector would
> guide me.
> The wires are marked with numbers for the terminals but my wires had
> darkened and discolored so I couldn’t read most of them. But inside the
> plug are very small numbers that correspond to the terminals.
> I hooked the wires back up but I had a long one left that went to the
> number 4 terminal. There was a number four terminal at the top of the board
> that was bent over so it would not be used. This was a long wire so I knew
> that it went to the bottom of the board. I was left with one unused
> terminal between number nine and number eleven. But it was labeled with a 1
> besides it. Where did the number four wire go?
>
> I finally called Jim Miller and he checked a board in his shop and
> verified that the wire number 4 was plugged into the terminal Marked with a
> 1.
>
> So if anyone has to figure out the connections by the little numbers
> inside the Molex plug they are all correct EXCEPT wire 4.
>
> Emery Stora
> 77 Kingsley
> Frederick CO
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
Jim Kanomata
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.gmcrvparts.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502
|
|
|