Home » Public Forums » GMCnet » [GMCnet] Tid Bit. Cheep grease isn't worth it.
[GMCnet] Tid Bit. Cheep grease isn't worth it. [message #356603] |
Thu, 09 July 2020 19:39 |
BobDunahugh
Messages: 2465 Registered: October 2010 Location: Cedar Rapids, IA
Karma: 11
|
Senior Member |
|
|
I'm not into the makeup of greases. My reference is from observations ONLY. Others can cover that.
Owned many Bobcat skid stir end loaders. Over many years. Still have one. Use it all the time. I observed that if I used cheap grease on it. I'd have to grease all joints. About every 2 hours. If I used the most expensive grease. I could run all day. Those joints on the Bobcat. Are much like the pins that our GMC's have at the rear. It didn't seem to be related to brand. Or type of grease. Just cost.
I don't think that GMC owner pay enough attention to those rear pins. I've heard owners say. That they grease their rear pins every other oil change. That's CRAZY to me. If you have EVER changed those pins. It's a HUGE pain in the ass. And all other parts that you have. I have a grease gun that I always have on board. And give each of the 8-grease fittings. One pump every 1000 miles. The front suspension. Every oil change. It's a 5-minute task. And CHEEP.
Bob Dunahugh
78 Royale since 2003
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
Re: [GMCnet] Tid Bit. Cheep grease isn't worth it. [message #356606 is a reply to message #356603] |
Thu, 09 July 2020 22:02 |
mghamms
Messages: 466 Registered: March 2016 Location: Ware, Massachusetts
Karma: 2
|
Senior Member |
|
|
I use a Dow molybdenum grease. Not sure the exact one off hand.
I learned that the machinery i work on lasts forever with it.
Other lesser greases sometime only minutes.
1977 Kingsley 455 as stock as it gets except lots of Ragusa parts
|
|
|
Re: [GMCnet] Tid Bit. Cheep grease isn't worth it. [message #356607 is a reply to message #356606] |
Thu, 09 July 2020 23:26 |
Ken Burton
Messages: 10030 Registered: January 2004 Location: Hebron, Indiana
Karma: 10
|
Senior Member |
|
|
For just normal fittings I always buy 3% moly grease.
For bearings that might get very warm, I always use Valvoline SynPower or Valvoline Full Synthetic Moly-fortified Gray grease.
I never use and recommend against Mobil One Synthetic due to it's propensity to separate the lubricant from the thickner (Usually Lithium) when left sitting over time. I have not checked to see what Mobile one uses as a thickener.
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
|
|
|
|
Re: [GMCnet] Tid Bit. Cheep grease isn't worth it. [message #356631 is a reply to message #356613] |
Fri, 10 July 2020 14:52 |
Keith V
Messages: 2337 Registered: March 2008 Location: Mounds View,MN
Karma: 0
|
Senior Member |
|
|
Bob, how did you know you needed to grease every 2 hours?
________________________________
From: Gmclist on behalf of Les Burt via Gmclist
Sent: Friday, July 10, 2020 5:42 AM
To: gmclist@list.gmcnet.org
Cc: Les Burt
Subject: Re: [GMCnet] Tid Bit. Cheep grease isn't worth it.
We all need to be cautious when selecting our greases. Some work better than others, but comparability is also important. Mixing incompatible greases can cause poor lubrication and premature wear.
Here is a good link to help explain the compatibility issues. You can also simply search “grease thickener compatibility”
https://www.machinerylubrication.com/Read/30727/determine-grease-compatibility
Les Burt
Montreal
'75 Eleganza 26'
> On Jul 10, 2020, at 12:27 AM, Ken Burton via Gmclist wrote:
>
> For just normal fittings I always buy 3% moly grease.
>
> For bearings that might get very warm, I always use Valvoline SynPower or Valvoline Full Synthetic Moly-fortified Gray grease.
>
> I never use and recommend against Mobil One Synthetic due to it's propensity to separate the lubricant from the thickner (Usually Lithium) when left
> sitting over time. I have not checked to see what Mobile one uses as a thickener.
> --
> Ken Burton - N9KB
> 76 Palm Beach
> Hebron, Indiana
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Keith Vasilakes
Mounds View. MN
75 ex Royale GMC
ask me about MicroLevel
Cell, 763-732-3419
My427v8@hotmail.com
|
|
|
|
Re: [GMCnet] Tid Bit. Cheep grease isn't worth it. [message #356656 is a reply to message #356603] |
Sat, 11 July 2020 08:08 |
JohnL455
Messages: 4447 Registered: October 2006 Location: Woodstock, IL
Karma: 12
|
Senior Member |
|
|
After 2 events I stopped buying Mobil 1 grease. Binding in upper intermediate shaft CV. And dripping red oil on top of my shoes and shop floor every time I picked up the grease gun. Synpower has been renamed Valvoline Full Synthetic. It has worked miracles with longevity on other things where nothing else worked or lasted. My seat of pants test. All I buy. I believe Dave L still likes Mobil 1 for front bearings, That should be a sealed (hopefully) environment where the phase separation is reunited with use.
John Lebetski
Woodstock, IL
77 Eleganza II
[Updated on: Sat, 11 July 2020 08:09] Report message to a moderator
|
|
|
|
Re: [GMCnet] Tid Bit. Cheep grease isn't worth it. [message #356668 is a reply to message #356603] |
Sat, 11 July 2020 15:04 |
kingd
Messages: 592 Registered: June 2004
Karma: 2
|
Senior Member |
|
|
I think I can get this correct. On the forum, quite awhile back (years) there was a discussion about
the CV joint in the GMCMH steering column. Some found that only grease with "moly" would stp the notchy
feeling. (actually more than a feeling)
DAVE KING
lurker, wannabe
Toronto, Ontario, Canada
|
|
|
Re: [GMCnet] Tid Bit. Cheep grease isn't worth it. [message #356674 is a reply to message #356668] |
Sat, 11 July 2020 16:05 |
Ken Henderson
Messages: 8726 Registered: March 2004 Location: Americus, GA
Karma: 9
|
Senior Member |
|
|
"From the horse's mouth": A LONG time ago, maybe in 2000, I was headed
from S. GA to Orlando in the GMC. The steering became difficult --
"notchy". I started pulling into large parking lots to do crazy turns,
thinking to get what were "obviously" worn balls in the steering joints
repositioned. I had enough success to make it all the way to Jim Bounds'
GMC Coop.
I disassembled the upper CV joint and found the balls and races in
apparently perfect condition. Lubricating the assembly with light motor
oil, I expected it to move easily with no loads applied -- but it didn't.
With big screwdriver handles stuck into the open ends of the CV I could
change the position. While Jim was in his office calling around to find me
a new CV, I found an unopened tube of Valvoline Synpower with MSO2, the
first I'd ever seen. Knowing that MSO2 is similar to graphite, I opened
the tube and greased up the CV balls and races. Magically, the CV lost all
resistance to movement!
I told Jim to hang up the phone. Since then, I've used no other grease,
for anything, and have never had "notchy" steering again.
That's how the "rumor" got started. :-)
Ken H.
On Sat, Jul 11, 2020 at 4:05 PM Dave King via Gmclist <
gmclist@list.gmcnet.org> wrote:
> I think I can get this correct. On the forum, quite awhile back (years)
> there was a discussion about
> the CV joint in the GMCMH steering column. Some found that only grease
> with "moly" would stp the notchy
> feeling. (actually more than a feeling)
> --
> DAVE KING
> lurker, wannabe
> Toronto, Ontario, Canada
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Ken Henderson
Americus, GA
www.gmcwipersetc.com
Large Wiring Diagrams
76 X-Birchaven
76 X-Palm Beach
|
|
|
Re: [GMCnet] Tid Bit. Cheep grease isn't worth it. [message #356676 is a reply to message #356674] |
Sat, 11 July 2020 16:35 |
Ken Henderson
Messages: 8726 Registered: March 2004 Location: Americus, GA
Karma: 9
|
Senior Member |
|
|
Well, that statement "...for anything..." isn't quite right! I DO use
other, special-purpose such as dielectric and transmission assembly,
greases. I just don't use anything else for heavy-duty applications like
the suspension -- and wheel bearings. Someone reported having Synpower
harden in the tube. I have also had that happen a time or two, accompanied
by "bleeding" (similar to the common trait of Mobil 1). I doubt that the
condition occurs in an active joint, and in fact, find that the lubricity
of the hardened grease seems barely affected. Once or twice, I've been
unable to find Synpower and had to use Valvoline Durablend with MSO2 -- the
"dino" version of Synpower. I did so with some trepidation, but never saw
any negative effects (I've NOT tried it in CV joints).
Ken H.
On Sat, Jul 11, 2020 at 5:05 PM Ken Henderson
wrote:
> "From the horse's mouth": A LONG time ago, maybe in 2000, I was headed
> from S. GA to Orlando in the GMC. The steering became difficult --
> "notchy". I started pulling into large parking lots to do crazy turns,
> thinking to get what were "obviously" worn balls in the steering joints
> repositioned. I had enough success to make it all the way to Jim Bounds'
> GMC Coop.
>
> I disassembled the upper CV joint and found the balls and races in
> apparently perfect condition. Lubricating the assembly with light motor
> oil, I expected it to move easily with no loads applied -- but it didn't.
> With big screwdriver handles stuck into the open ends of the CV I could
> change the position. While Jim was in his office calling around to find me
> a new CV, I found an unopened tube of Valvoline Synpower with MSO2, the
> first I'd ever seen. Knowing that MSO2 is similar to graphite, I opened
> the tube and greased up the CV balls and races. Magically, the CV lost all
> resistance to movement!
>
> I told Jim to hang up the phone. Since then, I've used no other grease,
> for anything, and have never had "notchy" steering again.
>
> That's how the "rumor" got started. :-)
>
> Ken H.
>
>
> On Sat, Jul 11, 2020 at 4:05 PM Dave King via Gmclist gmclist@list.gmcnet.org> wrote:
>
>> I think I can get this correct. On the forum, quite awhile back (years)
>> there was a discussion about
>> the CV joint in the GMCMH steering column. Some found that only grease
>> with "moly" would stp the notchy
>> feeling. (actually more than a feeling)
>> --
>> DAVE KING
>> lurker, wannabe
>> Toronto, Ontario, Canada
>>
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Ken Henderson
Americus, GA
www.gmcwipersetc.com
Large Wiring Diagrams
76 X-Birchaven
76 X-Palm Beach
|
|
|
Re: [GMCnet] Tid Bit. Cheep grease isn't worth it. [message #356704 is a reply to message #356676] |
Sun, 12 July 2020 21:56 |
Richard Denney
Messages: 920 Registered: April 2010
Karma: 9
|
Senior Member |
|
|
Rick fought a binding steering column, with a CV joint he had lubed with
Mobil One, all the way from Northern Virginia to a rally in North Carolina.
Nervous wreck on arrival. On disassembly, found galled and pitted balls in
the joint.
Messed with replacement 5/8” balls—nope—and finally hitched a ride with
KenHen to an Autozone. He pointed to the Valvoline Synpower, and said,
“Boy, buy this!”
Drove it home two days later with galled and pitted bearings...that
nevertheless worked perfectly.
Rick “now buys and uses Synpower for everything, even bicycle wheels and
bottom bracket bearings” Denney
On Sat, Jul 11, 2020 at 5:36 PM Ken Henderson via Gmclist <
gmclist@list.gmcnet.org> wrote:
> Well, that statement "...for anything..." isn't quite right! I DO use
> other, special-purpose such as dielectric and transmission assembly,
> greases. I just don't use anything else for heavy-duty applications like
> the suspension -- and wheel bearings. Someone reported having Synpower
> harden in the tube. I have also had that happen a time or two, accompanied
> by "bleeding" (similar to the common trait of Mobil 1). I doubt that the
> condition occurs in an active joint, and in fact, find that the lubricity
> of the hardened grease seems barely affected. Once or twice, I've been
> unable to find Synpower and had to use Valvoline Durablend with MSO2 -- the
> "dino" version of Synpower. I did so with some trepidation, but never saw
> any negative effects (I've NOT tried it in CV joints).
>
> Ken H.
>
> On Sat, Jul 11, 2020 at 5:05 PM Ken Henderson
> wrote:
>
>> "From the horse's mouth": A LONG time ago, maybe in 2000, I was headed
>> from S. GA to Orlando in the GMC. The steering became difficult --
>> "notchy". I started pulling into large parking lots to do crazy turns,
>> thinking to get what were "obviously" worn balls in the steering joints
>> repositioned. I had enough success to make it all the way to Jim Bounds'
>> GMC Coop.
>>
>> I disassembled the upper CV joint and found the balls and races in
>> apparently perfect condition. Lubricating the assembly with light motor
>> oil, I expected it to move easily with no loads applied -- but it didn't.
>> With big screwdriver handles stuck into the open ends of the CV I could
>> change the position. While Jim was in his office calling around to find
> me
>> a new CV, I found an unopened tube of Valvoline Synpower with MSO2, the
>> first I'd ever seen. Knowing that MSO2 is similar to graphite, I opened
>> the tube and greased up the CV balls and races. Magically, the CV lost
> all
>> resistance to movement!
>>
>> I told Jim to hang up the phone. Since then, I've used no other grease,
>> for anything, and have never had "notchy" steering again.
>>
>> That's how the "rumor" got started. :-)
>>
>> Ken H.
>>
>>
>> On Sat, Jul 11, 2020 at 4:05 PM Dave King via Gmclist > gmclist@list.gmcnet.org> wrote:
>>
>>> I think I can get this correct. On the forum, quite awhile back (years)
>>> there was a discussion about
>>> the CV joint in the GMCMH steering column. Some found that only grease
>>> with "moly" would stp the notchy
>>> feeling. (actually more than a feeling)
>>> --
>>> DAVE KING
>>> lurker, wannabe
>>> Toronto, Ontario, Canada
>>>
>>> _______________________________________________
>>> GMCnet mailing list
>>> Unsubscribe or Change List Options:
>>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>>
>>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
'73 X-Glacier 230 "Jaws"
Northern Virginia
Offlist email: rick at rickdenney dot com
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
Re: [GMCnet] Tid Bit. Cheep grease isn't worth it. [message #356711 is a reply to message #356704] |
Mon, 13 July 2020 09:10 |
Keith V
Messages: 2337 Registered: March 2008 Location: Mounds View,MN
Karma: 0
|
Senior Member |
|
|
When I first bought my coach my steering shaft was seized and there was no boot.
I prompt 'rebuilt' it, got the shaft apart, took the CV joint completely apart and mixed up all the balls.
I lubed it with my favorite bearing grease and it was notchy beyond belief. After a consult with the GMC forum, I changed over to Synpower. Problem solved, smooth as butter now.
Thank you Ken!
Keith Vasilakes
1975 Royale
Microlevel
________________________________
From: Gmclist on behalf of Richard Denney via Gmclist
Sent: Sunday, July 12, 2020 9:56 PM
To: gmclist@list.gmcnet.org
Cc: Richard Denney
Subject: Re: [GMCnet] Tid Bit. Cheep grease isn't worth it.
Rick fought a binding steering column, with a CV joint he had lubed with
Mobil One, all the way from Northern Virginia to a rally in North Carolina.
Nervous wreck on arrival. On disassembly, found galled and pitted balls in
the joint.
Messed with replacement 5/8” balls—nope—and finally hitched a ride with
KenHen to an Autozone. He pointed to the Valvoline Synpower, and said,
“Boy, buy this!”
Drove it home two days later with galled and pitted bearings...that
nevertheless worked perfectly.
Rick “now buys and uses Synpower for everything, even bicycle wheels and
bottom bracket bearings” Denney
On Sat, Jul 11, 2020 at 5:36 PM Ken Henderson via Gmclist <
gmclist@list.gmcnet.org> wrote:
> Well, that statement "...for anything..." isn't quite right! I DO use
> other, special-purpose such as dielectric and transmission assembly,
> greases. I just don't use anything else for heavy-duty applications like
> the suspension -- and wheel bearings. Someone reported having Synpower
> harden in the tube. I have also had that happen a time or two, accompanied
> by "bleeding" (similar to the common trait of Mobil 1). I doubt that the
> condition occurs in an active joint, and in fact, find that the lubricity
> of the hardened grease seems barely affected. Once or twice, I've been
> unable to find Synpower and had to use Valvoline Durablend with MSO2 -- the
> "dino" version of Synpower. I did so with some trepidation, but never saw
> any negative effects (I've NOT tried it in CV joints).
>
> Ken H.
>
> On Sat, Jul 11, 2020 at 5:05 PM Ken Henderson
> wrote:
>
>> "From the horse's mouth": A LONG time ago, maybe in 2000, I was headed
>> from S. GA to Orlando in the GMC. The steering became difficult --
>> "notchy". I started pulling into large parking lots to do crazy turns,
>> thinking to get what were "obviously" worn balls in the steering joints
>> repositioned. I had enough success to make it all the way to Jim Bounds'
>> GMC Coop.
>>
>> I disassembled the upper CV joint and found the balls and races in
>> apparently perfect condition. Lubricating the assembly with light motor
>> oil, I expected it to move easily with no loads applied -- but it didn't.
>> With big screwdriver handles stuck into the open ends of the CV I could
>> change the position. While Jim was in his office calling around to find
> me
>> a new CV, I found an unopened tube of Valvoline Synpower with MSO2, the
>> first I'd ever seen. Knowing that MSO2 is similar to graphite, I opened
>> the tube and greased up the CV balls and races. Magically, the CV lost
> all
>> resistance to movement!
>>
>> I told Jim to hang up the phone. Since then, I've used no other grease,
>> for anything, and have never had "notchy" steering again.
>>
>> That's how the "rumor" got started. :-)
>>
>> Ken H.
>>
>>
>> On Sat, Jul 11, 2020 at 4:05 PM Dave King via Gmclist > gmclist@list.gmcnet.org> wrote:
>>
>>> I think I can get this correct. On the forum, quite awhile back (years)
>>> there was a discussion about
>>> the CV joint in the GMCMH steering column. Some found that only grease
>>> with "moly" would stp the notchy
>>> feeling. (actually more than a feeling)
>>> --
>>> DAVE KING
>>> lurker, wannabe
>>> Toronto, Ontario, Canada
>>>
>>> _______________________________________________
>>> GMCnet mailing list
>>> Unsubscribe or Change List Options:
>>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>>
>>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
'73 X-Glacier 230 "Jaws"
Northern Virginia
Offlist email: rick at rickdenney dot com
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Keith Vasilakes
Mounds View. MN
75 ex Royale GMC
ask me about MicroLevel
Cell, 763-732-3419
My427v8@hotmail.com
|
|
|
Re: [GMCnet] Tid Bit. Cheep grease isn't worth it. [message #356779 is a reply to message #356603] |
Tue, 14 July 2020 16:48 |
captjack
Messages: 271 Registered: February 2010 Location: Sebastopol, California
Karma: 1
|
Senior Member |
|
|
Although I'm using the Valvoline Synpower grease that has been recommended, I discovered that even it can "dry out." When I've had it in my grease gun for a few months, the constant pressure of the spring that pressurizes the grease and keeps it ready to pump out, causes the liquid components to separate out and it's apparent when one looks at texture of the grease coming out of the gun. It's also obvious because of the puddle of liquid that accumulates on the floor under the gun. So, hard as it is to pull the spring back to its lock point, especially when the grease level gets low, doing it seems to have solved the problem.
Jack Christensen - K6ROW,
'76 Glenbrook/Clasco - "The Silver Bullet",
Sebastopol, CA
|
|
|
Re: [GMCnet] Tid Bit. Cheep grease isn't worth it. [message #356780 is a reply to message #356779] |
Tue, 14 July 2020 17:16 |
Ken Henderson
Messages: 8726 Registered: March 2004 Location: Americus, GA
Karma: 9
|
Senior Member |
|
|
Jack,
I've had the same problem with Synpower. Aside from the loss of
''spreadability", I don't think the lubricity is much affected -- 'tho' it
is hard to pump. :-) I also try to remember to pull the plunger out for
storage.
Ken H.
On Tue, Jul 14, 2020 at 5:49 PM Jack Christensen via Gmclist <
gmclist@list.gmcnet.org> wrote:
> Although I'm using the Valvoline Synpower grease that has been
> recommended, I discovered that even it can "dry out." When I've had it in
> my grease
> gun for a few months, the constant pressure of the spring that pressurizes
> the grease and keeps it ready to pump out, causes the liquid components to
> separate out and it's apparent when one looks at texture of the grease
> coming out of the gun. It's also obvious because of the puddle of liquid
> that
> accumulates on the floor under the gun. So, hard as it is to pull the
> spring back to its lock point, especially when the grease level gets low,
> doing
> it seems to have solved the problem.
> --
> Jack Christensen - K6ROW,
> '76 Glenbrook/Clasco - "The Silver Bullet",
> Sebastopol, CA
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Ken Henderson
Americus, GA
www.gmcwipersetc.com
Large Wiring Diagrams
76 X-Birchaven
76 X-Palm Beach
|
|
|
Goto Forum:
Current Time: Sun Sep 22 21:30:08 CDT 2024
Total time taken to generate the page: 0.01327 seconds
|