Home » Public Forums » GMCnet » [GMCnet] Norcold part
[GMCnet] Norcold part [message #341629] |
Sun, 10 March 2019 19:13 |
Len Novak
Messages: 676 Registered: February 2004 Location: Las Vegas, NV
Karma: -3
|
Senior Member |
|
|
Went to fire up the fridge today, would not light and when it did it cut out
immediately.
I found the problem. There is a small copper washer on the gas input line
that
goes to the gas orifice. It ruptured.
Anyone know of a source for that copper washer/gasket?
My temp fix will be using some Permatex Copper gasket as a sealer until I
find a replacement.
Thanks,
Len and Pat Novak
1978 GMC Kingsley
The Beast II with dash lights that work and labels you can see!
Fallbrook, CA new email: B52Rule@Roadrunner.Com
http://www.gmcmhphotos.com/photos/showgallery.php?cat=4375
www.bdub.net/novak/
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Len and Pat Novak
1978 GMC Kingsley
The Beast II with dash lights that work and labels you can see!
Las Vegas, NV new email: B52sRule@Gmail.com
http://www.gmcmhphotos.com/photos/showgallery.php?cat=4375
www.bdub.net/novak/
|
|
|
Re: [GMCnet] Norcold part [message #341630 is a reply to message #341629] |
Sun, 10 March 2019 19:19 |
Patrick Flowers
Messages: 195 Registered: February 2004
Karma: -24
|
Senior Member |
|
|
https://thenorcoldguy.com/
On 2019-03-10 20:13, Len Novak via Gmclist wrote:
> Went to fire up the fridge today, would not light and when it did it
> cut out
> immediately.
>
> I found the problem. There is a small copper washer on the gas input
> line
> that
> goes to the gas orifice. It ruptured.
> Anyone know of a source for that copper washer/gasket?
>
> My temp fix will be using some Permatex Copper gasket as a sealer until
> I
> find a replacement.
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Patrick Flowers
GMCnet Listmaster
'73 CanyonLands
Tyrone, GA
|
|
|
|
Re: [GMCnet] Norcold part [message #341632 is a reply to message #341631] |
Sun, 10 March 2019 22:50 |
jimk
Messages: 6734 Registered: July 2006 Location: Belmont, CA
Karma: 9
|
Senior Member |
|
|
Gon to your RV parts dealer with your model # and get the correct part.
On Sun, Mar 10, 2019 at 8:00 PM Emery Stora via Gmclist <
gmclist@list.gmcnet.org> wrote:
> My local Autozone carries an assortment if copper washers in a box behind
> the counter. Some are flat and some are dished to seal on brass fittings.
>
> Emery Stora
>
>> On Mar 10, 2019, at 7:19 PM, Patrick Flowers via Gmclist gmclist@list.gmcnet.org> wrote:
>>
>> https://thenorcoldguy.com/
>>
>>> On 2019-03-10 20:13, Len Novak via Gmclist wrote:
>>> Went to fire up the fridge today, would not light and when it did it
> cut out
>>> immediately.
>>> I found the problem. There is a small copper washer on the gas input
> line
>>> that
>>> goes to the gas orifice. It ruptured.
>>> Anyone know of a source for that copper washer/gasket?
>>> My temp fix will be using some Permatex Copper gasket as a sealer until
> I
>>> find a replacement.
>>
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
Jim Kanomata
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.appliedgmc.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502
|
|
|
Re: [GMCnet] Norcold part [message #341650 is a reply to message #341631] |
Mon, 11 March 2019 16:55 |
Len Novak
Messages: 676 Registered: February 2004 Location: Las Vegas, NV
Karma: -3
|
Senior Member |
|
|
Thanks! I sent them an email. I have a Norcold 8663, older that dirt.
Len and Pat Novak
1978 GMC Kingsley
The Beast II with dash lights that work and labels you can see!
Fallbrook, CA new email: B52Rule@Roadrunner.Com
http://www.gmcmhphotos.com/photos/showgallery.php?cat=4375
www.bdub.net/novak/
-----Original Message-----
From: Gmclist [mailto:gmclist-bounces@list.gmcnet.org] On Behalf Of Emery
Stora via Gmclist
Sent: Sunday, March 10, 2019 8:00 PM
To: gmclist@list.gmcnet.org
Cc: Emery Stora
Subject: Re: [GMCnet] Norcold part
My local Autozone carries an assortment if copper washers in a box behind
the counter. Some are flat and some are dished to seal on brass fittings.
Emery Stora
> On Mar 10, 2019, at 7:19 PM, Patrick Flowers via Gmclist
wrote:
>
> https://thenorcoldguy.com/
>
>> On 2019-03-10 20:13, Len Novak via Gmclist wrote:
>> Went to fire up the fridge today, would not light and when it did it cut
out
>> immediately.
>> I found the problem. There is a small copper washer on the gas input
line
>> that
>> goes to the gas orifice. It ruptured.
>> Anyone know of a source for that copper washer/gasket?
>> My temp fix will be using some Permatex Copper gasket as a sealer until I
>> find a replacement.
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
---
This email has been checked for viruses by AVG.
https://www.avg.com
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Len and Pat Novak
1978 GMC Kingsley
The Beast II with dash lights that work and labels you can see!
Las Vegas, NV new email: B52sRule@Gmail.com
http://www.gmcmhphotos.com/photos/showgallery.php?cat=4375
www.bdub.net/novak/
|
|
|
Re: [GMCnet] Norcold part [message #341689 is a reply to message #341630] |
Wed, 13 March 2019 11:13 |
Len Novak
Messages: 676 Registered: February 2004 Location: Las Vegas, NV
Karma: -3
|
Senior Member |
|
|
No parts available,,,,,,,,,,,,,,,,,
Len and Pat Novak
1978 GMC Kingsley
The Beast II with dash lights that work and labels you can see!
Fallbrook, CA new email: B52Rule@Roadrunner.Com
http://www.gmcmhphotos.com/photos/showgallery.php?cat=4375
www.bdub.net/novak/
-----Original Message-----
From: Gmclist [mailto:gmclist-bounces@list.gmcnet.org] On Behalf Of Patrick
Flowers via Gmclist
Sent: Sunday, March 10, 2019 5:20 PM
To: gmclist@list.gmcnet.org
Cc: Patrick Flowers
Subject: Re: [GMCnet] Norcold part
https://thenorcoldguy.com/
On 2019-03-10 20:13, Len Novak via Gmclist wrote:
> Went to fire up the fridge today, would not light and when it did it
> cut out
> immediately.
>
> I found the problem. There is a small copper washer on the gas input
> line
> that
> goes to the gas orifice. It ruptured.
> Anyone know of a source for that copper washer/gasket?
>
> My temp fix will be using some Permatex Copper gasket as a sealer until
> I
> find a replacement.
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
---
This email has been checked for viruses by AVG.
https://www.avg.com
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Len and Pat Novak
1978 GMC Kingsley
The Beast II with dash lights that work and labels you can see!
Las Vegas, NV new email: B52sRule@Gmail.com
http://www.gmcmhphotos.com/photos/showgallery.php?cat=4375
www.bdub.net/novak/
|
|
|
Re: [GMCnet] Norcold part [message #341690 is a reply to message #341650] |
Wed, 13 March 2019 11:46 |
GatsbysCruise
Messages: 261 Registered: January 2017 Location: Waukegan, Illinois
Karma: 3
|
Senior Member |
|
|
>>>>>> Thanks! I sent them an email. I have a Norcold 8663, older that dirt.
Len and Pat Novak
1978 GMC Kingsley <<<<<<
My Norcold is a 3 way. Gas - Electric 120v ac - 12vdc. I like this frig a lot and have used
all three options over time. There is the right time to use them and not to use them. its
a learning curve.
It has been one of the best refrigerators for the RV that I have ever had.
Now for the shocker. I bought it as a replacement to a (other brand) back in the late 1980's.
Thats just a few years back I guess, lol.
Over time I have learned a few things.
First, they are not supposed to last this long. If your Norcold is over 10 years old, you need to look at the coils in back.
You can sort of look at them with a flashlight and mirror from the access panel.
Those coils are made of steel. They are subject to the weather, even though they are inside that refer pocket and with the
heat and cool of the weather and refer actions, the paint cracks, moisture gets in and rust starts.
Rust eating its way through the metal of the coil is what will let the amonia leak out and end that life span of that cooler
unit.
The other concern is the control switch for turning it on and turning on the edge heaters.
The switch that I speak of is located between the freezer and the refrigerator, between the doors smack dab in the middle
of the shelf. Its a nice looking mini rocker, and is a 2 pole double throw, as I recall.
Its placement was a mistake and causes problems down the road.
The refer will sweat in the summer and this special switch gets wet and will corrode. EVentually it will stop making contact
and you have to replace this expensive switch. I am on my 2nd and due for a third if I can find one.
The switch allows turning the refer on with or without the edge heaters on to keep the sweat off.
I have never had a problem with my eyebrow controls for this frig.
Getting back to those metal coils.... After about a 10 year run in my SOB RV I had removed this 3 way Norcold when The RV was scrapped,
I liked the Norcold and wanted to try to preserve it.
I inspected the metal tubes and found some surface rust so while it was out, I tried to sand the rust off and used POR15 to coat the surface
in an attempt to make the life of the frig longer.
Still running today, knock on wood. But metal is tough to save and her time will come.
When that day happens, she can be rebuilt with either an electric or another ammonia based cooling system, and maybe some added foam insulation
where ever I can stuff it inside.
If your Norcold is really OLDER THAN DIRT, you should really inspect those coils for rust. You may be near the time to replace the cooling
unit.
GatsbysCruise. \
74GMC260 Former Glacier Model style. \
Waukegan, Illinois \ Keep those MiniDiscs Spinning \ MY GREYHOUND IS FASTER THAN YOUR HONOR ROLL STUDENT \ WindowsXP-Win7-Win8.1-UBUNTU STUDIO - UBUNTU VOYAGER - Berzin Auto Center
|
|
|
Re: [GMCnet] Norcold part [message #341691 is a reply to message #341629] |
Wed, 13 March 2019 12:17 |
rallymaster
Messages: 662 Registered: February 2004 Location: North Plains, ORYGUN
Karma: -4
|
Senior Member |
|
|
The Amish cooling unit rebuild guy
http://www.fixyourfridge.com
Leon Herschberger, owner
National RV Refrigeration
5660 N SR 5
Shipshewana, IN 46565
As to where to stat looking for a new cooling unit.
Try this link
http://www.rvcoolingunit.net/servlet/StoreFront
They advertise the Amish Cooling units.
RonC
On Wed, 13 Mar 2019 10:46:53 -0600 slc via Gmclist
writes:
>>>> >>> Thanks! I sent them an email. I have a Norcold 8663, older
> that dirt.
>
> Len and Pat Novak
> 1978 GMC Kingsley and not to use them. its
> a learning curve.
>
> It has been one of the best refrigerators for the RV that I have
> ever had.
>
> Now for the shocker. I bought it as a replacement to a (other
> brand) back in the late 1980's.
>
> Thats just a few years back I guess, lol.
>
> Over time I have learned a few things.
>
> First, they are not supposed to last this long. If your Norcold is
> over 10 years old, you need to look at the coils in back.
> You can sort of look at them with a flashlight and mirror from the
> access panel.
> Those coils are made of steel. They are subject to the weather,
> even though they are inside that refer pocket and with the
> heat and cool of the weather and refer actions, the paint cracks,
> moisture gets in and rust starts.
> Rust eating its way through the metal of the coil is what will let
> the amonia leak out and end that life span of that cooler
> unit.
>
Ron & Linda Clark
North Plains, ORYGUN
1978 Eleganza II
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Ron & Linda Clark
North Plains, ORYGUN
78 Eleganza II
|
|
|
Re: [GMCnet] Norcold part [message #341694 is a reply to message #341690] |
Wed, 13 March 2019 14:02 |
Len Novak
Messages: 676 Registered: February 2004 Location: Las Vegas, NV
Karma: -3
|
Senior Member |
|
|
I have a 8336, 3 way. So far it has been bulletproof. We had a problem
several years ago as it would not cool. We took it out of the coach, pulled
the coils, turned them upside down and whacked them with a plastic hammer.
I ran just the coils and after that they work just fine. The unit is about
25 plus years old. I have the original manuals and bill of sale from the
PO.
I have never has a problem with the eyebrow unit. I have pulled it, cleaned
it and that is about all.
I have never used that rocker switch and it has been off since I bought the
coach about 10 years ago.
I was looking at an Atwood Refrigerator Model: HE-0601 helium if I could not
get this one running.
Len and Pat Novak
1978 GMC Kingsley
The Beast II with dash lights that work and labels you can see!
Fallbrook, CA new email: B52Rule@Roadrunner.Com
http://www.gmcmhphotos.com/photos/showgallery.php?cat=4375
www.bdub.net/novak/
-----Original Message-----
From: Gmclist [mailto:gmclist-bounces@list.gmcnet.org] On Behalf Of slc via
Gmclist
Sent: Wednesday, March 13, 2019 9:47 AM
To: gmclist@list.gmcnet.org
Cc: slc
Subject: Re: [GMCnet] Norcold part
>>>> >> Thanks! I sent them an email. I have a Norcold 8663, older that
dirt.
Len and Pat Novak
1978 GMC Kingsley
Len and Pat Novak
1978 GMC Kingsley
The Beast II with dash lights that work and labels you can see!
Las Vegas, NV new email: B52sRule@Gmail.com
http://www.gmcmhphotos.com/photos/showgallery.php?cat=4375
www.bdub.net/novak/
|
|
|
Re: [GMCnet] Norcold part [message #341695 is a reply to message #341689] |
Wed, 13 March 2019 15:21 |
emerystora
Messages: 4442 Registered: January 2004
Karma: 13
|
Senior Member |
|
|
Len
You can take that switch apart and clean up the terminals. Then put in some dielectric grease to keep out moisture and stop corrosion.
I did this to mine and the switch worked fine afterwards.
Emery Stora
77 Kingsley
Frederick, CO
Emery
> On Mar 13, 2019, at 12:13 PM, Len Novak via Gmclist wrote:
>
> No parts available,,,,,,,,,,,,,,,,,
>
> Len and Pat Novak
> 1978 GMC Kingsley
> The Beast II with dash lights that work and labels you can see!
> Fallbrook, CA new email: B52Rule@Roadrunner.Com
> http://www.gmcmhphotos.com/photos/showgallery.php?cat=4375
>
> www.bdub.net/novak/
>
>
>
>
>
> -----Original Message-----
> From: Gmclist [mailto:gmclist-bounces@list.gmcnet.org] On Behalf Of Patrick
> Flowers via Gmclist
> Sent: Sunday, March 10, 2019 5:20 PM
> To: gmclist@list.gmcnet.org
> Cc: Patrick Flowers
> Subject: Re: [GMCnet] Norcold part
>
> https://thenorcoldguy.com/
>
>> On 2019-03-10 20:13, Len Novak via Gmclist wrote:
>> Went to fire up the fridge today, would not light and when it did it
>> cut out
>> immediately.
>>
>> I found the problem. There is a small copper washer on the gas input
>> line
>> that
>> goes to the gas orifice. It ruptured.
>> Anyone know of a source for that copper washer/gasket?
>>
>> My temp fix will be using some Permatex Copper gasket as a sealer until
>> I
>> find a replacement.
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
> ---
> This email has been checked for viruses by AVG.
> https://www.avg.com
>
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
Re: [GMCnet] Norcold part [message #341696 is a reply to message #341695] |
Wed, 13 March 2019 16:15 |
GatsbysCruise
Messages: 261 Registered: January 2017 Location: Waukegan, Illinois
Karma: 3
|
Senior Member |
|
|
I would think if it gets serious enough to need to repair or replace the fridge,
It may be money saving to just replace the cooling unit. You can go with gas
or electric.
Another option is to look at the low power fridges. I think they are electric
are well insulated and have special motors for the freon compressor to use
very low power.
My last choice would be to replace like for like today.
just my thoughts
slc
GatsbysCruise. \
74GMC260 Former Glacier Model style. \
Waukegan, Illinois \ Keep those MiniDiscs Spinning \ MY GREYHOUND IS FASTER THAN YOUR HONOR ROLL STUDENT \ WindowsXP-Win7-Win8.1-UBUNTU STUDIO - UBUNTU VOYAGER - Berzin Auto Center
|
|
|
Re: [GMCnet] Norcold part [message #341697 is a reply to message #341695] |
Wed, 13 March 2019 16:17 |
GatsbysCruise
Messages: 261 Registered: January 2017 Location: Waukegan, Illinois
Karma: 3
|
Senior Member |
|
|
"" Len
You can take that switch apart and clean up the terminals. Then put in some dielectric grease to keep out moisture and stop corrosion.
I did this to mine and the switch worked fine afterwards.
Emery Stora
77 Kingsley
Frederick, CO " "
EMORY
I wasn't aware that switch could be disassembled. We are talking about the mini rocker switch, right??
It appeared sealed when I pulled it. I'll have to pull it again and look closer...
Thanks for the thought.
slc
GatsbysCruise. \
74GMC260 Former Glacier Model style. \
Waukegan, Illinois \ Keep those MiniDiscs Spinning \ MY GREYHOUND IS FASTER THAN YOUR HONOR ROLL STUDENT \ WindowsXP-Win7-Win8.1-UBUNTU STUDIO - UBUNTU VOYAGER - Berzin Auto Center
|
|
|
Re: [GMCnet] Norcold part [message #341700 is a reply to message #341696] |
Wed, 13 March 2019 16:54 |
Len Novak
Messages: 676 Registered: February 2004 Location: Las Vegas, NV
Karma: -3
|
Senior Member |
|
|
A tiny broke gasket in the burner assembly wont stop me from fixing the
unit.
But just in case.................... Atwood Refrigerator Model: HE-0601
Len and Pat Novak
1978 GMC Kingsley
The Beast II with dash lights that work and labels you can see!
Fallbrook, CA new email: B52Rule@Roadrunner.Com
http://www.gmcmhphotos.com/photos/showgallery.php?cat=4375
www.bdub.net/novak/
-----Original Message-----
From: Gmclist [mailto:gmclist-bounces@list.gmcnet.org] On Behalf Of slc via
Gmclist
Sent: Wednesday, March 13, 2019 2:15 PM
To: gmclist@list.gmcnet.org
Cc: slc
Subject: Re: [GMCnet] Norcold part
I would think if it gets serious enough to need to repair or replace the
fridge,
It may be money saving to just replace the cooling unit. You can go with
gas
or electric.
Another option is to look at the low power fridges. I think they are
electric
are well insulated and have special motors for the freon compressor to use
very low power.
My last choice would be to replace like for like today.
just my thoughts
slc
--
GatsbysCruise. \
74GMC260 Former Glacier Model style. \
Waukegan, Illinois \ Keep those MiniDiscs Spinning \ MY GREYHOUND IS FASTER
THAN YOUR HONOR ROLL STUDENT \ WindowsXP-Win7-Win8.1-UBUNTU STUDIO -
UBUNTU VOYAGER - Berzin Auto Center
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
---
This email has been checked for viruses by AVG.
https://www.avg.com
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Len and Pat Novak
1978 GMC Kingsley
The Beast II with dash lights that work and labels you can see!
Las Vegas, NV new email: B52sRule@Gmail.com
http://www.gmcmhphotos.com/photos/showgallery.php?cat=4375
www.bdub.net/novak/
|
|
|
Re: [GMCnet] Norcold part [message #341757 is a reply to message #341632] |
Sun, 17 March 2019 16:47 |
Len Novak
Messages: 676 Registered: February 2004 Location: Las Vegas, NV
Karma: -3
|
Senior Member |
|
|
Update.
I could not find the part anywhere so I used Permatex Ultra Copper Gasket
sealer around the burner where the copper washer lives. I let it set
overnight and fired it off Thursday morning. It is still running fine. Not
bad for a 25+ year old fridge.
Len and Pat Novak
1978 GMC Kingsley
The Beast II with dash lights that work and labels you can see!
Fallbrook, CA new email: B52Rule@Roadrunner.Com
http://www.gmcmhphotos.com/photos/showgallery.php?cat=4375
www.bdub.net/novak/
-----Original Message-----
From: Gmclist [mailto:gmclist-bounces@list.gmcnet.org] On Behalf Of Jim
Kanomata via Gmclist
Sent: Sunday, March 10, 2019 8:50 PM
To: gmclist@list.gmcnet.org
Cc: Jim Kanomata
Subject: Re: [GMCnet] Norcold part
Gon to your RV parts dealer with your model # and get the correct part.
On Sun, Mar 10, 2019 at 8:00 PM Emery Stora via Gmclist <
gmclist@list.gmcnet.org> wrote:
> My local Autozone carries an assortment if copper washers in a box behind
> the counter. Some are flat and some are dished to seal on brass fittings.
>
> Emery Stora
>
>> On Mar 10, 2019, at 7:19 PM, Patrick Flowers via Gmclist gmclist@list.gmcnet.org> wrote:
>>
>> https://thenorcoldguy.com/
>>
>>> On 2019-03-10 20:13, Len Novak via Gmclist wrote:
>>> Went to fire up the fridge today, would not light and when it did it
> cut out
>>> immediately.
>>> I found the problem. There is a small copper washer on the gas input
> line
>>> that
>>> goes to the gas orifice. It ruptured.
>>> Anyone know of a source for that copper washer/gasket?
>>> My temp fix will be using some Permatex Copper gasket as a sealer until
> I
>>> find a replacement.
>>
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
Jim Kanomata
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.appliedgmc.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
---
This email has been checked for viruses by AVG.
https://www.avg.com
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Len and Pat Novak
1978 GMC Kingsley
The Beast II with dash lights that work and labels you can see!
Las Vegas, NV new email: B52sRule@Gmail.com
http://www.gmcmhphotos.com/photos/showgallery.php?cat=4375
www.bdub.net/novak/
|
|
|
Re: [GMCnet] Norcold part [message #341758 is a reply to message #341757] |
Sun, 17 March 2019 16:58 |
Ken Henderson
Messages: 8726 Registered: March 2004 Location: Americus, GA
Karma: 9
|
Senior Member |
|
|
Len,
Just in case your Permatex doesn't continue to hold up, Harbor Freight
carries an inexpensive box of assorted copper washers. It probably does
not have to begin as a conical shape. But, this may be a way to make one
that is:
http://www.gmcmhphotos.com/photos/g4452-flare-fitting-repair-with-copper-seal.html
Ken H.
Americus, GA
'76 X-Birchaven w/Cad500/Howell EFI & EBL,
Manny Brakes & 1-Ton, Troy-Bilt APU, etc., etc., etc.
www.gmcwipersetc.com
On Sun, Mar 17, 2019 at 5:47 PM Len Novak via Gmclist <
gmclist@list.gmcnet.org> wrote:
> Update.
>
> I could not find the part anywhere so I used Permatex Ultra Copper Gasket
> sealer around the burner where the copper washer lives. I let it set
> overnight and fired it off Thursday morning. It is still running fine.
> Not
> bad for a 25+ year old fridge.
>
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Ken Henderson
Americus, GA
www.gmcwipersetc.com
Large Wiring Diagrams
76 X-Birchaven
76 X-Palm Beach
|
|
|
Re: [GMCnet] Norcold part [message #341764 is a reply to message #341758] |
Sun, 17 March 2019 22:14 |
jimk
Messages: 6734 Registered: July 2006 Location: Belmont, CA
Karma: 9
|
Senior Member |
|
|
On Sun, Mar 17, 2019 at 5:59 PM Ken Henderson via Gmclist <
gmclist@list.gmcnet.org> wrote:
> Len,
>
> Just in case your Permatex doesn't continue to hold up, Harbor Freight
> carries an inexpensive box of assorted copper washers. It probably does
> not have to begin as a conical shape. But, this may be a way to make one
> that is:
>
> http://www.gmcmhphotos.com/photos/g4452-flare-fitting-repair-with-copper-seal.html
>
> Ken H.
> Americus, GA
> '76 X-Birchaven w/Cad500/Howell EFI & EBL,
> Manny Brakes & 1-Ton, Troy-Bilt APU, etc., etc., etc.
> www.gmcwipersetc.com
>
>
> On Sun, Mar 17, 2019 at 5:47 PM Len Novak via Gmclist gmclist@list.gmcnet.org> wrote:
>
>> Update.
>>
>> I could not find the part anywhere so I used Permatex Ultra Copper Gasket
>> sealer around the burner where the copper washer lives. I let it set
>> overnight and fired it off Thursday morning. It is still running fine.
>> Not
>> bad for a 25+ year old fridge.
>>
>>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
Jim Kanomata
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.appliedgmc.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502
|
|
|
Goto Forum:
Current Time: Sun Sep 29 07:27:39 CDT 2024
Total time taken to generate the page: 0.00662 seconds
|