Ladder Bracket Mounting [message #339573] |
Sat, 15 December 2018 16:39 |
Carl S.
Messages: 4186 Registered: January 2009 Location: Tucson, AZ.
Karma: 13
|
Senior Member |
|
|
The top ladder mounts (the ones on the top of the "removable panel" on my coach have been fastened to the coach with what looks like mollys. The are rusty and ugly, and a source of a leak that has plagued me for 10+ years.
My question is, are rivnuts a sufficient way to anchor the ladder bracket to the panel? Or should I go to all the trouble to remove the inner trim panel and add some sort of backing to that area?
I plan to add some rubber washers between the bracket and the body to eliminate the leak, but I'm wondering if the panel is strong enough to support the stress of the ladder brackets just in the fiberglass.
Thanks,
Carl Stouffer
'75 ex Palm Beach
Tucson, AZ.
Chuck Aulgur Reaction Arm Disc Brakes, Quadrabags, 3.70 LSD final drive, Lenzi knuckles/hubs, Dodge Truck 16" X 8" front wheels, Rear American Eagles, Solar battery charging. GMCSJ and GMCMI member
|
|
|
Re: [GMCnet] Ladder Bracket Mounting [message #339574 is a reply to message #339573] |
Sat, 15 December 2018 17:25 |
JerryW
Messages: 256 Registered: August 2018
Karma: 1
|
Senior Member |
|
|
Rivnuts will work fine. I’ve had them in for years. They self seal so I’ve had no leaks.
Emery Stora
77 Kingsley
Frederick CO
> On Dec 15, 2018, at 3:39 PM, Carl Stouffer wrote:
>
> The top ladder mounts (the ones on the top of the "removable panel" on my coach have been fastened to the coach with what looks like mollys. The are
> rusty and ugly, and a source of a leak that has plagued me for 10+ years.
>
> My question is, are rivnuts a sufficient way to anchor the ladder bracket to the panel? Or should I go to all the trouble to remove the inner trim
> panel and add some sort of backing to that area?
>
> I plan to add some rubber washers between the bracket and the body to eliminate the leak, but I'm wondering if the panel is strong enough to support
> the stress of the ladder brackets just in the fiberglass.
>
> Thanks,
> --
> Carl Stouffer
> '75 ex Palm Beach
> Tucson, AZ.
> Chuck Aulgur Reaction Arm Disc Brakes, Quadrabags, 3.70 LSD final drive, Lenzi knuckles/hubs, Dodge Truck 16" X 8" front wheels, Rear American Eagles,
> Solar battery charging. GMCSJ and GMCMI member
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
|
Re: Ladder Bracket Mounting [message #339582 is a reply to message #339573] |
Sun, 16 December 2018 14:21 |
Larry
Messages: 2875 Registered: January 2004 Location: Menomonie, WI
Karma: 10
|
Senior Member |
|
|
Dale Ropp did a session at one of the last GMCMI conferences about Fiberglass repairing. His method of repairing stripped out FG holes was to soak ear plugs (you know, the type you use in your ears to block excessive sound) soak the ear plugs in fiberglass resin and push them into the hole. Once in the hole they expand to their original shape. After the resin hardens, grind off the excess on the outside and redrill the hole in a reinforced (by the ear plug) hole. Have not had occasion to try this, but sure seems like a excellent way to fix a stripped hole without having to take the inside panels off. JWIT
Larry
78 Royale w/500 Caddy
Menomonie, WI.
[Updated on: Sun, 16 December 2018 14:23] Report message to a moderator
|
|
|
Re: Ladder Bracket Mounting [message #339584 is a reply to message #339582] |
Sun, 16 December 2018 17:20 |
Carl S.
Messages: 4186 Registered: January 2009 Location: Tucson, AZ.
Karma: 13
|
Senior Member |
|
|
Thanks Larry. The holes are in pretty good shape, if I can find the right size rivnuts to go in them. If not, I may have to revert to that method.
Carl Stouffer
'75 ex Palm Beach
Tucson, AZ.
Chuck Aulgur Reaction Arm Disc Brakes, Quadrabags, 3.70 LSD final drive, Lenzi knuckles/hubs, Dodge Truck 16" X 8" front wheels, Rear American Eagles, Solar battery charging. GMCSJ and GMCMI member
|
|
|