Home » Public Forums » GMCnet » [GMCnet] Wipers re-assemblying
[GMCnet] Wipers re-assemblying [message #324738] |
Mon, 09 October 2017 10:11 |
gmc gmc
Messages: 69 Registered: May 2009
Karma: 0
|
Member |
|
|
Hello All... been awhile Mike Derr from Madison WI here...
78' I have original wipers, bought replacement rubbers... not sure how to
reassemble, I see those metal u-shapped 1" clips... then holes for a bolt?
pin?
I googled to see a assemble help but was not able to find any.
thanks all.
Mike
PS: we are planning a lil trip Wed. to Door County here...
Pss: kinda have older tires good tread, but little sidewall fine lines, I
feel should be ok though.
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
Re: [GMCnet] Wipers re-assemblying [message #324742 is a reply to message #324738] |
Mon, 09 October 2017 11:19 |
Ken Henderson
Messages: 8726 Registered: March 2004 Location: Americus, GA
Karma: 9
|
Senior Member |
|
|
Mike,
Just remember: If one of those "little sidewall fine lines" decides, as
they often do, to let all the air out instantaneously, you'll probably have
a $2000+ fiberglass repair bill.
Ken H.
On Mon, Oct 9, 2017 at 11:11 AM, gmc gmc wrote:
> Hello All... been awhile Mike Derr from Madison WI here...
>
> 78' I have original wipers, bought replacement rubbers... not sure how to
> reassemble, I see those metal u-shapped 1" clips... then holes for a bolt?
> pin?
>
> I googled to see a assemble help but was not able to find any.
>
> thanks all.
>
> Mike
>
> PS: we are planning a lil trip Wed. to Door County here...
>
> Pss: kinda have older tires good tread, but little sidewall fine lines, I
> feel should be ok though.
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Ken Henderson
Americus, GA
www.gmcwipersetc.com
Large Wiring Diagrams
76 X-Birchaven
76 X-Palm Beach
|
|
|
Re: [GMCnet] Wipers re-assemblying [message #324746 is a reply to message #324742] |
Mon, 09 October 2017 12:29 |
gmc gmc
Messages: 69 Registered: May 2009
Karma: 0
|
Member |
|
|
ok Ken, agree... ok I am Sam's member, what is best recommended tires for
$$$ value these days?
thx Mike
On Mon, Oct 9, 2017 at 11:19 AM, Ken Henderson
wrote:
> Mike,
>
> Just remember: If one of those "little sidewall fine lines" decides, as
> they often do, to let all the air out instantaneously, you'll probably have
> a $2000+ fiberglass repair bill.
>
> Ken H.
>
>
> On Mon, Oct 9, 2017 at 11:11 AM, gmc gmc wrote:
>
>> Hello All... been awhile Mike Derr from Madison WI here...
>>
>> 78' I have original wipers, bought replacement rubbers... not sure how to
>> reassemble, I see those metal u-shapped 1" clips... then holes for a
> bolt?
>> pin?
>>
>> I googled to see a assemble help but was not able to find any.
>>
>> thanks all.
>>
>> Mike
>>
>> PS: we are planning a lil trip Wed. to Door County here...
>>
>> Pss: kinda have older tires good tread, but little sidewall fine lines,
> I
>> feel should be ok though.
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
Re: [GMCnet] Wipers re-assemblying [message #324748 is a reply to message #324738] |
Mon, 09 October 2017 12:53 |
|
Brian K
Messages: 75 Registered: May 2017 Location: Sherman Oaks, CA
Karma: 0
|
Member |
|
|
Hi Mike,
On my very first weekend trip after buying my GMC, I had two blow outs, one which ripped out the front wheel covering and now I have a nice fiberglass tear (looks like Wolverine of X-Men took a piece out of my fender).
On the way back my second was a flat, and when the rig was up on the flat bed, that's when I noticed the same thing you did: Fine lines and cracks on all the tires. I was near a Goodyear place, so I had them replace everything. It cost me about $1800 or so, but I'm happy.
The brand I got was: Goodyear Armor Max G947 RSS
https://www.goodyeartrucktires.com/pdf/resources/publications/armor_max_brochure.pdf
I've put about 5000 miles on them and they've held up really well. I also invested in a Tire Pressure Monitoring system which gives me a little piece of mind too.
Good luck,
Brian
Brian K
1977 Eleganza II, TZE167V100261
Sherman Oaks, CA
Rebuilt 455, New brake system, a lot of Original Equipment ready to fall apart (discovering more as I go along....)
|
|
|
|
Re: [GMCnet] Wipers re-assemblying [message #324752 is a reply to message #324746] |
Mon, 09 October 2017 13:27 |
Richard Denney
Messages: 920 Registered: April 2010
Karma: 9
|
Senior Member |
|
|
At the risk of rekindling past tire wars, I have found that tires replaced
while still young more readily get away with being cheap. I've been using
whatever inexpensive polyester-sidewall tires my tire guy has been able to
find. The last set was Load Range E only because they were cheaper than the
Load Range D alternatives. They are four years old and I'll replace them
year after next.
I also inflate them strictly per manufacturer recommendations, which
depends on load. For my very light early 23' coach, I use 65 psi in the
front and 45-50 psi in the back.
I've had one flat caused by a nail, but no other tire issues.
I think my last set cost about $750 mounted, but I removed and replaced the
wheels myself.
Now, the tires on my beater pickups, well, let's not talk about those.
Rick "knocking on wood" Denney
On Mon, Oct 9, 2017 at 1:30 PM gmc gmc wrote:
> ok Ken, agree... ok I am Sam's member, what is best recommended tires for
> $$$ value these days?
>
> thx Mike
>
> On Mon, Oct 9, 2017 at 11:19 AM, Ken Henderson
> wrote:
>
>> Mike,
>>
>> Just remember: If one of those "little sidewall fine lines" decides, as
>> they often do, to let all the air out instantaneously, you'll probably
> have
>> a $2000+ fiberglass repair bill.
>>
>> Ken H.
>>
>>
>> On Mon, Oct 9, 2017 at 11:11 AM, gmc gmc wrote:
>>
>>> Hello All... been awhile Mike Derr from Madison WI here...
>>>
>>> 78' I have original wipers, bought replacement rubbers... not sure how
> to
>>> reassemble, I see those metal u-shapped 1" clips... then holes for a
>> bolt?
>>> pin?
>>>
>>> I googled to see a assemble help but was not able to find any.
>>>
>>> thanks all.
>>>
>>> Mike
>>>
>>> PS: we are planning a lil trip Wed. to Door County here...
>>>
>>> Pss: kinda have older tires good tread, but little sidewall fine
> lines,
>> I
>>> feel should be ok though.
>>> _______________________________________________
>>> GMCnet mailing list
>>> Unsubscribe or Change List Options:
>>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>>
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
Rick Denney
73 x-Glacier 230 "Jaws"
Off-list email to rick at rickdenney dot com
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
|
Re: [GMCnet] Wipers re-assemblying [message #324756 is a reply to message #324738] |
Mon, 09 October 2017 14:33 |
cbryan
Messages: 451 Registered: May 2012 Location: Ennis, Texas
Karma: 3
|
Senior Member |
|
|
How true about tire replacement. I was going to say if you really have to run them, make sure they are properly inflated. Just running a short distance very underinflated can damage a tire. Blowouts are so sudden and disconcerting, and expensive, that it's worth the money and trouble to get new tires.
Like Rick (who puts really good autobiographical observations between his first and last name) Denney says, I get the cheapest with the proper load range and go with them. Not worth the money just to replace. I give the carcasses to my neighbor for his flatbed trailer. He runs them happily.
Carey
Carey from Ennis, Texas
78 Royale, 500 Cadillac, Rance Baxter EFI.
|
|
|
Re: [GMCnet] Wipers re-assemblying [message #324786 is a reply to message #324738] |
Tue, 10 October 2017 09:11 |
jhbridges
Messages: 8412 Registered: May 2011 Location: Braselton ga
Karma: -74
|
Senior Member |
|
|
What Rick and Carey said. Unless the coach is on the road full time, they will age out long before they wear out. Shop price. I've been using Cooper Challenger HT3s purely because I deal with the same place for some decades and he gives me a price on them... and goes and gets me new ones from the warehouse... usually 6 weeks old or less. I go 7 years and then Craigslist them as older with good tread. Takeoffs work fine on peoples' pickups who wear them out.
== johnny
Foolish Carriage, 76 26' Eleganza(?) with beaucoup mods and add - ons.
Braselton, Ga.
I forgive them all, save those who hurt the dogs. They must answer to me in hell
|
|
|
Re: [GMCnet] Wipers re-assemblying [message #324791 is a reply to message #324738] |
Tue, 10 October 2017 10:18 |
JohnL455
Messages: 4447 Registered: October 2006 Location: Woodstock, IL
Karma: 12
|
Senior Member |
|
|
The wiper blades should install with a nut driver on the nylock nut and a small flat blade on the screw.
The Cooper HT3s are the best value for money out there. From a previous Michelin LTX/ MS owner who has 6 perfect looking LTXs in his garage, only because of age discrimination
John Lebetski
Woodstock, IL
77 Eleganza II
|
|
|
Re: [GMCnet] Wipers re-assemblying [message #324793 is a reply to message #324791] |
Tue, 10 October 2017 10:56 |
jimk
Messages: 6734 Registered: July 2006 Location: Belmont, CA
Karma: 9
|
Senior Member |
|
|
Should you want more instruction, I can take few pictures to show you as to
how to do it.
Also a picture of your present wiper arm as I need to know if it is the
origional round shaft arm or flat NEW style.
On Tue, Oct 10, 2017 at 8:18 AM, John R. Lebetski
wrote:
> The wiper blades should install with a nut driver on the nylock nut and a
> small flat blade on the screw.
>
> The Cooper HT3s are the best value for money out there. From a previous
> Michelin LTX/ MS owner who has 6 perfect looking LTXs in his garage, only
> because of age discrimination
> --
> John Lebetski
> Woodstock, IL
> 77 Eleganza II
>
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
Jim Kanomata
Applied/GMC, Newark,CA
jimk@appliedairfilters.com
http://www.appliedgmc.com
1-800-752-7502
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Jim Kanomata
Applied/GMC
jimk@appliedairfilters.com
www.appliedgmc.com
1-800-752-7502
|
|
|
Re: [GMCnet] Wipers re-assemblying [message #324794 is a reply to message #324793] |
Tue, 10 October 2017 11:29 |
Mr ERFisher
Messages: 7117 Registered: August 2005
Karma: 2
|
Senior Member |
|
|
Read here
http://www.gmcmhphotos.com/photos/g3587-lumina-apv-wipers.html
On Tue, Oct 10, 2017 at 8:57 AM Jim Kanomata wrote:
> Should you want more instruction, I can take few pictures to show you as to
> how to do it.
> Also a picture of your present wiper arm as I need to know if it is the
> origional round shaft arm or flat NEW style.
>
> On Tue, Oct 10, 2017 at 8:18 AM, John R. Lebetski >
> wrote:
>
>> The wiper blades should install with a nut driver on the nylock nut and a
>> small flat blade on the screw.
>>
>> The Cooper HT3s are the best value for money out there. From a previous
>> Michelin LTX/ MS owner who has 6 perfect looking LTXs in his garage, only
>> because of age discrimination
>> --
>> John Lebetski
>> Woodstock, IL
>> 77 Eleganza II
>>
>>
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>
>
>
>
> --
> Jim Kanomata
> Applied/GMC, Newark,CA
> jimk@appliedairfilters.com
> http://www.appliedgmc.com
> 1-800-752-7502
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
Gene Fisher -- 74-23,77PB/ore/ca
“Give a man a fish; you have fed him for today --- give him a URL and
-------
http://gmcmotorhome.info/
Alternator Protection Cable
http://gmcmotorhome.info/APC.html
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
Re: [GMCnet] Wipers re-assemblying [message #324799 is a reply to message #324794] |
Tue, 10 October 2017 16:23 |
gmc gmc
Messages: 69 Registered: May 2009
Karma: 0
|
Member |
|
|
thanks all I got them on with screw n nut... one the fluid tube broke off
but ok for now...
someday I upgrade as others mentioned
thanks much. hitting the road tomorrow... to Door County WI
Cheers, Mike
78' Palm Beach painted, refurbished...
On Tue, Oct 10, 2017 at 11:29 AM, gene Fisher wrote:
> Read here
>
> http://www.gmcmhphotos.com/photos/g3587-lumina-apv-wipers.html
>
> On Tue, Oct 10, 2017 at 8:57 AM Jim Kanomata
> wrote:
>
>> Should you want more instruction, I can take few pictures to show you as
> to
>> how to do it.
>> Also a picture of your present wiper arm as I need to know if it is the
>> origional round shaft arm or flat NEW style.
>>
>> On Tue, Oct 10, 2017 at 8:18 AM, John R. Lebetski gransport7087@gmail.com
>>>
>> wrote:
>>
>>> The wiper blades should install with a nut driver on the nylock nut
> and a
>>> small flat blade on the screw.
>>>
>>> The Cooper HT3s are the best value for money out there. From a
> previous
>>> Michelin LTX/ MS owner who has 6 perfect looking LTXs in his garage,
> only
>>> because of age discrimination
>>> --
>>> John Lebetski
>>> Woodstock, IL
>>> 77 Eleganza II
>>>
>>>
>>> _______________________________________________
>>> GMCnet mailing list
>>> Unsubscribe or Change List Options:
>>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>>
>>
>>
>>
>> --
>> Jim Kanomata
>> Applied/GMC, Newark,CA
>> jimk@appliedairfilters.com
>> http://www.appliedgmc.com
>> 1-800-752-7502
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>>
> --
> Gene Fisher -- 74-23,77PB/ore/ca
> “Give a man a fish; you have fed him for today --- give him a URL and
> -------
> http://gmcmotorhome.info/
> Alternator Protection Cable
> http://gmcmotorhome.info/APC.html
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
Goto Forum:
Current Time: Fri Sep 27 07:02:40 CDT 2024
Total time taken to generate the page: 0.02563 seconds
|