Home » Public Forums » GMCnet » Mastertcool tubing flare tool
|
|
| Re: Mastertcool tubing flare tool [message #312208 is a reply to message #312205] |
Tue, 17 January 2017 11:36   |
GMC Cruse
Messages: 606
Registered: June 2009
Location: SE Michigan
Karma: 3
|
Senior Member |
|
|
dshafer wrote on Tue, 17 January 2017 10:28These were mentioned recently which spurred my interest. Usually $280 on eBay new and and around $200 used. Now on eBay for $46 new... but from a low feedback Chinese seller.
"Do you feel lucky? Well do you?" (paraphrased)
I did, so I "pulled the trigger".
I will update my buy some time in February... hopefully.
Dave
Do YOU fell lucky?? Click here.
http://www.ebay.com/itm/Mastercool-71475-PRO-Master-Universal-Hydraulic-Flaring-Tool-Set-/152399731704
I'd be real cautious of that seller, with that super low price and only 9 feedbacks and all are from sellers not buyers. It sounds like another Viair deal everybody jumped on earlier.
I have that kit and it works great but I got it from Toolopia and paid big bucks for it.
Mike K.
'75 PB
Southeast Michigan
|
|
|
|
| Re: Mastertcool tubing flare tool [message #312210 is a reply to message #312205] |
Tue, 17 January 2017 11:55 |
 |
Matt Colie
Messages: 8547
Registered: March 2007
Location: S.E. Michigan
Karma: 7
|
Senior Member |
|
|
dshafer wrote on Tue, 17 January 2017 10:28These were mentioned recently which spurred my interest. Usually $280 on eBay new and and around $200 used. Now on eBay for $46 new... but from a low feedback Chinese seller.
"Do you feel lucky? Well do you?" (paraphrased)
I did, so I "pulled the trigger".
I will update my buy some time in February... hopefully.
Dave
Do YOU fell lucky?? Click here.
http://www.ebay.com/itm/Mastercool-71475-PRO-Master-Universal-Hydraulic-Flaring-Tool-Set-/152399731704
Hot Dam Dave,
There are only two things that stop me from jumping on that one:
The first is the fact that there is one that I can and have borrowed locally.
The second is the "Mastercool&" name used.
This sort of thing is common in knock-off products. When I was the aftermarket at McCord Gasket, I was part of a lawsuit when a headgasket failed. When questioned I said that the failed part presented did not come from our plant. The plaintiff then produced the original box that not very clearly said "NIcCord" in a type face that was a near match to our logo.
I am still tempted to go on this one.
Well, I did and you will all love a lot of the reason.
I know where there is an original. I believe I can get my hands on it (along with Mike's long enough to find out if it is a real, functional tool or not.
I will sacrifice some tubing and then I will let the world know what I think.
What I decide may involve Ebay and Paypal because if this is a POS, I will probably not pay return shipping and get stuck for a re-stocking fee. I feel this effort may have enough value to the community to be worth 1/3 of a tank of fuel. I have had occasion to bring the power of Ebay and Paypal down on bad sellers before, and while I may not end up even on a Cash-Out-Of-Pocket account, I can have a real impact.
Watch this space.
Matt
Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL, GMCES
Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum Brakes with Applied Control Arms
SE Michigan - Near DTW - Twixt A2 and Detroit
|
|
|
|
| Re: Mastertcool tubing flare tool [message #312211 is a reply to message #312208] |
Tue, 17 January 2017 11:59 |
|
Matt Colie
Messages: 8547
Registered: March 2007
Location: S.E. Michigan
Karma: 7
|
Senior Member |
|
|
GMC Cruse wrote on Tue, 17 January 2017 12:36dshafer wrote on Tue, 17 January 2017 10:28These were mentioned recently which spurred my interest. Usually $280 on eBay new and and around $200 used. Now on eBay for $46 new... but from a low feedback Chinese seller.
"Do you feel lucky? Well do you?" (paraphrased)
I did, so I "pulled the trigger".
I will update my buy some time in February... hopefully.
Dave
Do YOU fell lucky?? Click here.
http://www.ebay.com/itm/Mastercool-71475-PRO-Master-Universal-Hydraulic-Flaring-Tool-Set-/152399731704
I'd be real cautious of that seller, with that super low price and only 9 feedbacks and all are from sellers not buyers. It sounds like another Viair deal everybody jumped on earlier.
I have that kit and it works great but I got it from Toolopia and paid big bucks for it.
Mike,
When I have it in hand, I will get with you and we can compare.
I will say again, if you have much steel flare to do, even the 300$ set could be a good investment.
Are you going to make the Lunch on Saturday?
Matt
Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL, GMCES
Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum Brakes with Applied Control Arms
SE Michigan - Near DTW - Twixt A2 and Detroit
|
|
|
|
| Re: [GMCnet] Mastertcool tubing flare tool [message #312213 is a reply to message #312211] |
Tue, 17 January 2017 13:22 |
Keith V
Messages: 2337
Registered: March 2008
Location: Mounds View,MN
Karma: 0
|
Senior Member |
|
|
I've switched to using 37' flares, they are reusable, and you can almost make them with a rock and a stick.
Slightly more expensive, but single digit dollars.
I can buy a whole lot of 37' hardware for $400
________________________________
From: Gmclist on behalf of Matt Colie
Sent: Tuesday, January 17, 2017 11:59:29 AM
To: gmclist@list.gmcnet.org
Subject: Re: [GMCnet] Mastertcool tubing flare tool
GMC Cruse wrote on Tue, 17 January 2017 12:36
> dshafer wrote on Tue, 17 January 2017 10:28
>> These were mentioned recently which spurred my interest. Usually $280 on eBay new and and around $200 used. Now on eBay for $46 new... but
>> from a low feedback Chinese seller.
>> "Do you feel lucky? Well do you?" (paraphrased)
>> I did, so I "pulled the trigger".
>> I will update my buy some time in February... hopefully.
>> Dave
>>
>> Do YOU fell lucky?? Click here.
>>
>> http://www.ebay.com/itm/Mastercool-71475-PRO-Master-Universal-Hydraulic-Flaring-Tool-Set-/152399731704
>
>
> I'd be real cautious of that seller, with that super low price and only 9 feedbacks and all are from sellers not buyers. It sounds like another
> Viair deal everybody jumped on earlier.
>
> I have that kit and it works great but I got it from Toolopia and paid big bucks for it.
Mike,
When I have it in hand, I will get with you and we can compare.
I will say again, if you have much steel flare to do, even the 300$ set could be a good investment.
Are you going to make the Lunch on Saturday?
Matt
--
Matt & Mary Colie - '73 Glacier 23 - Members GMCMI, GMCGL, GMCES
Still Loving OE Rear Drum Brakes with Applied Control Arms
SE Michigan - Twixt A2 and Detroit
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Keith Vasilakes
Mounds View. MN
75 ex Royale GMC
ask me about MicroLevel
Cell, 763-732-3419
My427v8@hotmail.com
|
|
|
|
| Re: [GMCnet] Mastertcool tubing flare tool [message #312226 is a reply to message #312213] |
Tue, 17 January 2017 18:22 |
|
Matt Colie
Messages: 8547
Registered: March 2007
Location: S.E. Michigan
Karma: 7
|
Senior Member |
|
|
Keith V wrote on Tue, 17 January 2017 14:22I've switched to using 37' flares, they are reusable, and you can almost make them with a rock and a stick.
Slightly more expensive, but single digit dollars.
I can buy a whole lot of 37' hardware for $400
Kieth,
45° flares are reusable too. Sometimes a 45°double flare used with a defective mating fitting will cause trouble, but the spring action of the folded tube can be a real benefit. As an instrument fitter, it did a lot of 37° flares. Many in lines specified for 5K hydraulic.
If you are using 37° tooling, don't use any DOT brake fittings or you will have a bad time and you will not be able to take the fitting up to stop a leak without damaging the mating surface. Now, if you get all the adapters and change everything to stainless with 37° flares. You can make it all be real good, but don't get it inspected in NY, NJ, PA or MA, because when they see the non-SAE or DOT fittings, you are toast. Our race car was great, but we had to cheat to get it registered in NY. (Story only if you buy the beer.)
Matt
Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL, GMCES
Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum Brakes with Applied Control Arms
SE Michigan - Near DTW - Twixt A2 and Detroit
|
|
|
|
| Re: Mastertcool tubing flare tool [message #312230 is a reply to message #312211] |
Tue, 17 January 2017 19:42 |
GMC Cruse
Messages: 606
Registered: June 2009
Location: SE Michigan
Karma: 3
|
Senior Member |
|
|
Quote:
Mike,
When I have it in hand, I will get with you and we can compare.
I will say again, if you have much steel flare to do, even the 300$ set could be a good investment.
Are you going to make the Lunch on Saturday?
Matt :Quote
As of now, I am planning to make it.
I've done 3 cars with the flaring tool so far and hopefully, in about a month I'll be ready to do the brake lines on my '35 Ford, plus got others in line so I am slowly getting my moneys worth.
Mike K.
'75 PB
Southeast Michigan
|
|
|
|
| Re: Mastertcool tubing flare tool [message #313317 is a reply to message #312205] |
Thu, 16 February 2017 10:36 |
dshafer
Messages: 68
Registered: June 2016
Location: SW Ohio
Karma: 3
|
Member |
|
|
This deal did not work out. I got a refund. "to good to be true". Not too disappointed. I wasn't too apprehensive either since I have confidence in Pay Pal. Still watching for another on E-Bay.
1977 26 foot 403
|
|
|
|
|
|
| Re: [GMCnet] Mastertcool tubing flare tool [message #313333 is a reply to message #313320] |
Thu, 16 February 2017 13:26 |
Keith V
Messages: 2337
Registered: March 2008
Location: Mounds View,MN
Karma: 0
|
Senior Member |
|
|
I use a pretty cheap flaring too and can make a leak free flare pretty reliably.
What I do;
*Use poly armor or the new copper lines, never the old crappy galvanized steel lines if you can help it, and never stainless. THOSE are hard to flare.
*Don't over crush the flare, so many people try and smash the hell out if the flare, but it needs to have some crush left for assembly!
*Start with a really clean square cut tube, a ragged or angled cut will make flaring very hard
*I file the ends square and clean
* lube everything, except the operator, lube them only after the flaring is done
*Remember Double flares are single use, if you get more out of them consider your self lucky
* I only use double flares if I have to, otherwise I use 37' AN Flares, they are so much easier to make and seal AND they are reusable!
________________________________
From: Gmclist on behalf of James Hupy
Sent: Thursday, February 16, 2017 11:09:16 AM
To: gmclist@list.gmcnet.org
Subject: Re: [GMCnet] Mastertcool tubing flare tool
Google "Eastwood" if you are looking for a good flaring tool for brake
lines and fuel lines. It takes a quality tool to perform double flares on
brake lines. If you are unsure of your skills in this arena, have an expert
do the flares for you. I do double flares often, and still occasionally
have trouble getting them leak free. Lots of variables here. Especially
near the master cylinder and the distribution valve. The new brass ones in
particular. Remember, "new" is only that, not necessarily good.
Jim Hupy
Salem, Or
78 GMC ROYALE 403
On Feb 16, 2017 8:54 AM, "David Shafer" wrote:
This deal did not work out. I got a refund. "to good to be true". Not too
disappointed. I wasn't too apprehensive either since I have confidence in
Pay Pal. Still watching for another on E-Bay.
--
1977 26 foot 403
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Keith Vasilakes
Mounds View. MN
75 ex Royale GMC
ask me about MicroLevel
Cell, 763-732-3419
My427v8@hotmail.com
|
|
|
|
Goto Forum:
Current Time: Wed Nov 06 12:35:05 CST 2024
Total time taken to generate the page: 0.01889 seconds
|
GMCforum
Search
Help
Register
Login
Home
