GMCforum: GMCnet » Power Steering Pulley Out of Alignment?

Home » Public Forums » GMCnet » Power Steering Pulley Out of Alignment?

Show: Today's Messages :: Polls :: Message Navigator

Power Steering Pulley Out of Alignment? [message #307708]

Fri, 23 September 2016 15:48

thainglo

Messages: 132
Registered: March 2015
Location: Iowa

Karma: 2

Senior Member

I've been away from the GMC for awhile but started it up today to take a quick ride around the block and make sure all systems were go. Heard a different kind of noise from the engine bay, so popped open the cover. Was reminded while looking at the front accessories that I was unable to get my power steering pulley back into full alignment after I changed the water pump (along with the aluminum radiator). I took a 20-sec video of it running and shutdown, would greatly appreciate anyone's thoughts.

https://youtu.be/f_fVjJZWHfU

The problem I remember having was the tightening of the belt for both the power steering and alternator would cause the bracket holding the power steering reservoir to start to tip in. The attachment bolts for the bracket were inboard of the pulley, nothing on the outside to keep it in place. I snapped a pic of the outer side of the bracket in hopes that could shed light.

http://www.gmcmhphotos.com/photos/uploads/42258/2016-09-23_15_15_15.jpg

Any guidance? I can see the alternator belt is twisted a little as it heads from the power steering pulley up to the alternator and I'm fairly certain that couldn't be good for long term survival.

Matt Sladek 1976 Eleganza II Coralville, IA

Report message to a moderator

Re: Power Steering Pulley Out of Alignment? [message #307709 is a reply to message #307708]

Fri, 23 September 2016 15:50

thainglo

Messages: 132
Registered: March 2015
Location: Iowa

Karma: 2

Senior Member

I can't explain why my picture is upside down and HUGE. It looks fine on the photo site.

I certainly hope nobody was injured standing on their head while investigating!

Matt Sladek 1976 Eleganza II Coralville, IA

Report message to a moderator

Re: Power Steering Pulley Out of Alignment? [message #307710 is a reply to message #307708]

Fri, 23 September 2016 17:08

C Boyd

Messages: 2629
Registered: April 2006

Karma: 18

Senior Member

Check the stud on front of engine. The power steering should be against the stud first with the top left radiator shroud bracket on the outside.

C. Boyd
76 Crestmont
East Tennessee

Report message to a moderator

Re: [GMCnet] Power Steering Pulley Out of Alignment? [message #307711 is a reply to message #307708]

Fri, 23 September 2016 17:10

bdub

Messages: 1578
Registered: February 2004
Location: Central Texas

Karma: 5

Senior Member

Page 9-15 has a diagram of all the bolts and brackets. I'd expect one of
the inner side bolts that connect the pump to the bracket.

Oh, and your video is marked private.

bdub
76 Palm Beach in Central Texas
www.bdub.net/GMCLinks.html
https://www.facebook.com/groups/classicgmcmotorhomes/
https://www.facebook.com/groups/gmcmm/

-----Original Message-----
From: Gmclist On Behalf Of Matt Sladek
Sent: Friday, September 23, 2016 3:49 PM

I've been away from the GMC for awhile but started it up today to take a
quick ride around the block and make sure all systems were go. Heard a
different kind of noise from the engine bay, so popped open the cover. Was
reminded while looking at the front accessories that I was unable to get my
power steering pulley back into full alignment after I changed the water
pump (along with the aluminum radiator). I took a 20-sec video of it
running and shutdown, would greatly appreciate anyone's thoughts.

https://youtu.be/f_fVjJZWHfU

The problem I remember having was the tightening of the belt for both the
power steering and alternator would cause the bracket holding the power
steering reservoir to start to tip in. The attachment bolts for the bracket
were inboard of the pulley, nothing on the outside to keep it in place.
I snapped a pic of the outer side of the bracket in hopes that could shed
light.

http://www.gmcmhphotos.com/photos/uploads/42258/2016-09-23_15_15_15.jpg

Any guidance? I can see the alternator belt is twisted a little as it heads
from the power steering pulley up to the alternator and I'm fairly certain
that couldn't be good for long term survival.

_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org

bdub
'76 Palm Beach/Central Texas
www.bdub.net
www.gmcmhphotos.com
www.gmcmotorhomemarketplace.com
www.gmcmhregistry.com
www.facebook.com/groups/classicgmcmotorhomes
www.facebook.com/groups/gmcmm

Report message to a moderator

Re: Power Steering Pulley Out of Alignment? [message #307713 is a reply to message #307708]

Fri, 23 September 2016 17:32

thainglo

Messages: 132
Registered: March 2015
Location: Iowa

Karma: 2

Senior Member

Thanks Billy. Video should now be viewable.

Matt Sladek 1976 Eleganza II Coralville, IA

Report message to a moderator

Re: Power Steering Pulley Out of Alignment? [message #307715 is a reply to message #307709]

Fri, 23 September 2016 19:21

wally

Messages: 643
Registered: August 2004
Location: Omaha Nebraska

Karma: 5

Senior Member

thainglo wrote on Fri, 23 September 2016 15:50

I can't explain why my picture is upside down and HUGE. It looks fine on the photo site.

I certainly hope nobody was injured standing on their head while investigating!

There is a strut that goes from the ex manifold bolt over to ps pump mount. I can't see if it is on yours.
http://www.gmcmhphotos.com/photos/power-level-valve-fitting/p60855-ps-pump-strut.html

Wally Anderson
Omaha NE
75 Glenbrook

Report message to a moderator

Re: Power Steering Pulley Out of Alignment? [message #307716 is a reply to message #307708]

Fri, 23 September 2016 19:33

thainglo

Messages: 132
Registered: March 2015
Location: Iowa

Karma: 2

Senior Member

You nailed it again Wally. That bracket is missing on my engine, and based off the condition of the exhaust manifold bolt, it has been missing for awhile.

Anyone have a spare?

Matt Sladek 1976 Eleganza II Coralville, IA

Report message to a moderator

Re: Power Steering Pulley Out of Alignment? [message #307755 is a reply to message #307708]

Sat, 24 September 2016 18:01

JohnS

Messages: 126
Registered: December 2014
Location: Vacaville, CA

Karma: -2

Senior Member

Also look closely at the parts breakdown and note that there should be a washer between the bracket and the pump on the bolt used to clamp the pump.
That will keep the pump reservoir from contacting the bracket and should help to straighten the pump. Tough to get that washer in, but as I found out, it is needed.

John Shutzbaugh, Vacaville, CA, ncserv@aol.com; 78 Buskirk stretch, "What were we thinking?"

Report message to a moderator

Previous Topic:	OEM Cruise Control Acting Strangely
Next Topic:	Buzz box replacement

Goto Forum:

-=] Back to Top [=-

Current Time: Thu Nov 07 09:35:24 CST 2024

Total time taken to generate the page: 0.01488 seconds