GMCforum: GMCnet » Tools for turn signal switch replacement at GMCMI rally

Home » Public Forums » GMCnet » Tools for turn signal switch replacement at GMCMI rally

Show: Today's Messages :: Polls :: Message Navigator

Tools for turn signal switch replacement at GMCMI rally [message #307269]

Sat, 17 September 2016 08:14

RF_Burns

Messages: 2277
Registered: June 2008
Location: S. Ontario, Canada

Karma: 3

Senior Member

Hi All
My turn signal switch does not latch for right turns, so I'm going to bring a replacement switch to the Mansfield Rally. Just wondering if anyone going there has a steering wheel puller and the spring compressor tools needed to do the job.

Thanks

Bruce Hislop
ON Canada
77PB, 455 Dick P. rebuilt, DynamicEFI EBL EFI & ESC.
1 ton front end
http://www.gmcmhphotos.com/photos/showphoto.php?photo=29001
My Staff says I never listen to them, or something like that

Report message to a moderator

Re: Tools for turn signal switch replacement at GMCMI rally [message #307270 is a reply to message #307269]

Sat, 17 September 2016 08:20

Ken Burton

Messages: 10030
Registered: January 2004
Location: Hebron, Indiana

Karma: 10

Senior Member

I should have those two in my coach hidden under my sofa. If not, we can always borrow one for free at a local AutoZone.

Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana

Report message to a moderator

Re: Tools for turn signal switch replacement at GMCMI rally [message #307271 is a reply to message #307269]

Sat, 17 September 2016 08:27

RF_Burns

Messages: 2277
Registered: June 2008
Location: S. Ontario, Canada

Karma: 3

Senior Member

Thanks Ken,
The local Canadian auto parts stores don't lend any tools, but they will sell them for the single use!

Report message to a moderator

Re: Tools for turn signal switch replacement at GMCMI rally [message #307272 is a reply to message #307269]

Sat, 17 September 2016 08:27

Matt Colie

Messages: 8547
Registered: March 2007
Location: S.E. Michigan

Karma: 7

Senior Member

RF_Burns wrote on Sat, 17 September 2016 09:14

Hi All
My turn signal switch does not latch for right turns, so I'm going to bring a replacement switch to the Mansfield Rally. Just wondering if anyone going there has a steering wheel puller and the spring compressor tools needed to do the job.

Thanks

KenB has said he would and as this seems to be an on going demand and the set is small, I think I will load my set also.
I do my best to not carry more than I expect to need, but this rally is so close to us that I will make this exception.

See you there. I guess we are bringing the coach, I thought we might just walk.

Matt

Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL, GMCES
Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum Brakes with Applied Control Arms
SE Michigan - Near DTW - Twixt A2 and Detroit

Report message to a moderator

Re: Tools for turn signal switch replacement at GMCMI rally [message #307274 is a reply to message #307272]

Sat, 17 September 2016 09:04

Ken Burton

Messages: 10030
Registered: January 2004
Location: Hebron, Indiana

Karma: 10

Senior Member

Bring them Matt, just in case I forget to make sure mine are in the coach. Thanks

Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana

Report message to a moderator

Previous Topic:	Trip report
Next Topic:	[GMCnet] headliner replacement help needed

Goto Forum:

-=] Back to Top [=-

Current Time: Sun Nov 17 14:40:27 CST 2024

Total time taken to generate the page: 0.00845 seconds