Home » Public Forums » GMCnet » screen door installation
screen door installation [message #305228] |
Wed, 10 August 2016 06:37 |
kstockwell
Messages: 367 Registered: May 2016 Location: Putney VT
Karma: 4
|
Senior Member |
|
|
My list gets 2-3 tasks entered for every one completed
I've got the screens replaced, and am ready to install the screen door I bought from Bill. I even got that wooden block to push the awning up so the screen doesn't get hit.
These directions, I don't even understand #2 (not a good sign, I know). And #4 is completely confusing even though there's a drawing.
http://bdub.net/manuals/Birch_Screen_Door_Installation_Instructions.pdf
What is the pull strap end, what is the door check strap? I don't have new door pins or new door trim- do I need these?
I don't have a rivet gun, is this required? ("bend hinge to fit before drilling for rivets")
#13 Why would I attach a cable from the vacuum component door, it is on the opposite side of the hinges and won't I hit my head on it?
Page 3, what?
I feel like a moron trying to follow this.
I believe my coach had a screen door at one time, there's a little nubbin that would be used to grab a roller. Maybe some of these instructions assume I have to do work that's already done? My screen door has hinges on it.
I can get photos later on. I figure I'll start this tomorrow after work when it's in the mid 90s.
And, what are the chances I'll be completely confused and can't do it and have the door off for an extended period of time- it's supposed to rain this weekend?
Thanks for any/all help.
kelly
1978 Kingsley
Putney VT
|
|
|
Re: [GMCnet] screen door installation [message #305230 is a reply to message #305228] |
Wed, 10 August 2016 07:57 |
bdub
Messages: 1578 Registered: February 2004 Location: Central Texas
Karma: 5
|
Senior Member |
|
|
The motorhome came with a strap attached to the door to keep it from
opening too far. There was another strap attached to the door beside the
latch to use to shut it.
Have a couple a these on hand:
https://www.amazon.com/Dorman-HELP-38400-Hinge-Bushing/dp/B0002JMRWI
Rivit gun is easy to come by if you need it. Ya probably won't need Page
3.
I'd probably have some way to block the weather JIC.
Good luck
bdub
On Wed, Aug 10, 2016 at 6:37 AM, kelly stockwell wrote:
> My list gets 2-3 tasks entered for every one completed
>
> I've got the screens replaced, and am ready to install the screen door I
> bought from Bill. I even got that wooden block to push the awning up so the
> screen doesn't get hit.
>
> These directions, I don't even understand #2 (not a good sign, I know).
> And #4 is completely confusing even though there's a drawing.
> http://bdub.net/manuals/Birch_Screen_Door_Installation_Instructions.pdf
>
> What is the pull strap end, what is the door check strap? I don't have
> new door pins or new door trim- do I need these?
> I don't have a rivet gun, is this required? ("bend hinge to fit before
> drilling for rivets")
> #13 Why would I attach a cable from the vacuum component door, it is on
> the opposite side of the hinges and won't I hit my head on it?
> Page 3, what?
> I feel like a moron trying to follow this.
>
> I believe my coach had a screen door at one time, there's a little nubbin
> that would be used to grab a roller. Maybe some of these instructions
> assume I have to do work that's already done? My screen door has hinges
> on it.
> I can get photos later on. I figure I'll start this tomorrow after work
> when it's in the mid 90s.
>
> And, what are the chances I'll be completely confused and can't do it and
> have the door off for an extended period of time- it's supposed to rain this
> weekend?
>
> Thanks for any/all help.
> kelly
> --
> 1978 Kingsley
> Putney VT
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
bdub
'76 Palm Beach/Central Texas
www.bdub.net
www.gmcmhphotos.com
www.gmcmotorhomemarketplace.com
www.gmcmhregistry.com
www.facebook.com/groups/classicgmcmotorhomes
www.facebook.com/groups/gmcmm
|
|
|
Re: screen door installation [message #305232 is a reply to message #305228] |
Wed, 10 August 2016 08:06 |
lqqkatjon
Messages: 2324 Registered: October 2010 Location: St. Cloud, MN
Karma: 5
|
Senior Member |
|
|
Kelly,
I am no expert, my screen door is still sitting idle waiting for me to have time to install it. But i have been trying to study up as much as I can for the project.
From what I understand, the original "NEW" screen door, came with the hinges not attached. and no holes in the door for the rivets. the process was to install the hinges, then fit the door, and mark, drill and mount the hinges to the door. I am told that makes proper door fitting easier.
I am assuming you have a used door, and the hinges are either already mounted/pop riveted to the door, or they were drilled off(like mine), yet the holes for the pop rivets are in the door. If that is the case, you should skip the "Pop rivet" step, and just hope it lines up. If it can't be made to line up, taking the hinges off the door, then welding the existing pop rivet holes up, and re-drilling/riveting could be needed.
I also believe could possibly need new door pins. The door pins for the Birch door I believe are a little longer then stock door pins. But I have seen a few different variety of door pins out there on coaches. I know mine needed to be longer and I bought two from Mr Burkitt. I also picked up new copper bushings when I was visiting Jim Bounds for the door hinges as well since i will be pulling and replacing pins on the door.
I think Step #2 is shortening the door pull strap on the inside of the door. It is the strap that is used to pull the door closed from the inside. I am guessing it needs to be shortened a little bit and that will make it sit tight against the door, as not to interfere with the screen door. You may have a different finish on the inside of your door, and not have this strap. Maybe these pictures will help:
http://www.gmcmhphotos.com/photos/entry-door-strap-fittings-restoration/p9499.html
as for step #4. This one makes me nervous. If yours had a screen door, it may have already been done, but that step is cutting the aluminum behind the door striker post. from what i can tell the door needs a flush path outside to inside, and that aluminum to the inside of where the door catch is, blocks the screen door and needs to be cut 3/4" to allow for the door to close fully. It makes me nervous because I do not like cutting things.... very permanent. Again, if you coach did have a screen door, that would already be cut. I think the term "pin shield" is a part that comes with the door.
I will try to see if I can get some pictures posted. I have been taking photos of the birch door installs I have run across.
take pictures as you do it, so it can help me out. I have been procrastinating on the job, and been busy.
Jon Roche
75 palm beach
EBL EFI, manny headers, Micro Level, rebuilt most of coach now.
St. Cloud, MN
http://lqqkatjon.blogspot.com/
|
|
|
Re: screen door installation [message #305233 is a reply to message #305228] |
Wed, 10 August 2016 08:12 |
lqqkatjon
Messages: 2324 Registered: October 2010 Location: St. Cloud, MN
Karma: 5
|
Senior Member |
|
|
The cord for vacuum door-
this is inside the vacuum door cabinet and only for the cabinet door itself. nothing attached to screen door. You do not want your vacuum cabinet door opening up and punching a hole in the screen door.
Jon Roche
75 palm beach
EBL EFI, manny headers, Micro Level, rebuilt most of coach now.
St. Cloud, MN
http://lqqkatjon.blogspot.com/
|
|
|
Re: screen door installation [message #305234 is a reply to message #305228] |
Wed, 10 August 2016 08:13 |
jhbridges
Messages: 8412 Registered: May 2011 Location: Braselton ga
Karma: -74
|
Senior Member |
|
|
I sold the Ragusa screen door which came on the new used coach. Useless article when one has large dogs. Easy to remove, I expect it would be fairly easy to install as well.
--johnny
Foolish Carriage, 76 26' Eleganza(?) with beaucoup mods and add - ons.
Braselton, Ga.
I forgive them all, save those who hurt the dogs. They must answer to me in hell
[Updated on: Wed, 10 August 2016 08:14] Report message to a moderator
|
|
|
|
Re: screen door installation [message #305238 is a reply to message #305228] |
Wed, 10 August 2016 09:10 |
kstockwell
Messages: 367 Registered: May 2016 Location: Putney VT
Karma: 4
|
Senior Member |
|
|
Thanks all!
Bill, those hinge pins, I'll be sure to have them- thank you
What you all say makes sense, there are a bunch of steps I won't need to do.
I will document my trials and tribulations to help and amuse the rest of you.
And duly noted on taking care for weather... I have an awning that should help
kelly
1978 Kingsley
Putney VT
[Updated on: Wed, 10 August 2016 09:14] Report message to a moderator
|
|
|
|
Re: [GMCnet] screen door installation [message #305242 is a reply to message #305228] |
Wed, 10 August 2016 10:52 |
Kosier
Messages: 834 Registered: February 2008
Karma: 1
|
Senior Member |
|
|
Kelly,
Instruction #2 refers to the horizontal pull strap (adapted from a Buick)
that lays horizontally on the door. It sticks out far enough to
interfere with the screen door. Shortening one end pulls it closer to the
door, eliminating the interference.
The other fabric strap to keep the door from swinging around and hitting the
body is located farther down. It has to be removed for
the screen door. You may find some of the holes where it was mounted.
Instruction #4 refers to the rubber covered metal shield on the door opening
frame that protects your body or clothing from catching
on the protruding door latch pin. The middle of the screen goes past it, so
it must be reworked.
On a new installation the hinges are not attached, as the coaches were not
all EXACTLY alike. A real pain sometimes to align.
The plastic trim around the door opening is a sorta' h shaped extrusion to
allow the door to seal to the opening. I had to put some
plastic cord I had behind (inside?) the trim to get it to line up right.
The trim is available new from Bob Burkitt, who has some other
small parts for the door.
It's been 32 years since I installed a door, so my memory is not real clear,
but this crowd will help you reach your goal.
Gary Kosier
77PB w/500Cad
Newark, Ohio
--------------------------------------------------
From: "kelly stockwell"
Sent: Wednesday, August 10, 2016 7:37 AM
To:
Subject: [GMCnet] screen door installation
> My list gets 2-3 tasks entered for every one completed
>
> I've got the screens replaced, and am ready to install the screen door I
> bought from Bill. I even got that wooden block to push the awning up so
> the
> screen doesn't get hit.
>
> These directions, I don't even understand #2 (not a good sign, I know).
> And #4 is completely confusing even though there's a drawing.
> http://bdub.net/manuals/Birch_Screen_Door_Installation_Instructions.pdf
>
> What is the pull strap end, what is the door check strap? I don't have
> new door pins or new door trim- do I need these?
> I don't have a rivet gun, is this required? ("bend hinge to fit before
> drilling for rivets")
> #13 Why would I attach a cable from the vacuum component door, it is on
> the opposite side of the hinges and won't I hit my head on it?
> Page 3, what?
> I feel like a moron trying to follow this.
>
> I believe my coach had a screen door at one time, there's a little nubbin
> that would be used to grab a roller. Maybe some of these instructions
> assume I have to do work that's already done? My screen door has hinges
> on it.
> I can get photos later on. I figure I'll start this tomorrow after work
> when it's in the mid 90s.
>
> And, what are the chances I'll be completely confused and can't do it and
> have the door off for an extended period of time- it's supposed to rain
> this
> weekend?
>
> Thanks for any/all help.
> kelly
> --
> 1978 Kingsley
> Putney VT
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
|
|
Re: [GMCnet] screen door installation [message #305264 is a reply to message #305248] |
Wed, 10 August 2016 23:08 |
Hal StClair
Messages: 971 Registered: March 2013 Location: Rio Rancho NM
Karma: -12
|
Senior Member |
|
|
The gentleman we bought our coach (1586) from was a retired machinist that tells of parts on the Lunar rover he machined of aluminum. He says it gives him great satisfaction to look at the moon and realize there are parts he built still there-imagine the feeling!!! (just a little off topic)
Hal
"I enjoy talking to you. Your mind appeals to me. It resembles my own mind, except you happen to be insane."
1977 Royale 101348,
1977 Royale 101586, Diesel powered,
1974 Eagle Bus 45',w/slideout,
Rio Rancho, NM
[Updated on: Wed, 10 August 2016 23:10] Report message to a moderator
|
|
|
|
|
|
Re: screen door installation [message #305297 is a reply to message #305228] |
Thu, 11 August 2016 18:35 |
kstockwell
Messages: 367 Registered: May 2016 Location: Putney VT
Karma: 4
|
Senior Member |
|
|
OK, that literally took 15 minutes
http://www.gmcmhphotos.com/photos/g6961-screen-door.html
I know lots of coaches have the same color scheme but could this be the screen door my coach had long ago? Although I don't see any grab for the double roller on the door handle.
I had to unscrew the catch because it was jammed in tight after inserting the new pins in the hinges (I shifted the roller out).
After bending/manipulating I moved the roller back to the position it was in.
It took me 6x longer to put the new aluminum screen in. I think they gave me spline that's too big, I actually ripped the screen a few times (you can see that in some pictures)
kelly
1978 Kingsley
Putney VT
|
|
|
Goto Forum:
Current Time: Mon Oct 14 16:16:05 CDT 2024
Total time taken to generate the page: 0.03883 seconds
|