Home » Public Forums » GMCnet » Setting the front ride height procedure
Re: [GMCnet] Setting the front ride height procedure [message #292860 is a reply to message #292851] |
Thu, 24 December 2015 11:15 |
Scott Nutter
Messages: 782 Registered: January 2015 Location: Houston/San Diego
Karma:
|
Senior Member |
|
|
Ken Burton's technique sounds more like the way the manual describes the procedure. The shop manual does not mention any steps of raising the front end. Also, all the informational videos on YouTube show the wheels on the ground during adjustments. Although the videos were all GMC trucks.
So, being my first time, I am going to err on the safe side. I will set the front ride height with the wheels OFF the ground. Once I'm under the coach I can actually get a better idea of what's going down there and the amount of force actually on the unloader tool. Then after the first test drive, I will fine tune the front height with the wheels ON the ground if I think I can do it safely. I will also try to post the end results with pictures. Scott
Scott Nutter
1978 Royale Center Kitchen, Patterson 455, switch pitch tranny, 3.21 final drive, Quad bags, Dave Lenzi super duty mid axle disc brakes, tankless water heater, everything Lenzi. Alex Ferrera installed MSD Atomic EFI
Houston, Texas
|
|
|
|
|
Setting the front ride height procedure
|
|
|
Re: Setting the front ride height procedure
By: Harry on Wed, 23 December 2015 15:18
|
|
|
Re: [GMCnet] Setting the front ride height procedure
By: jimk on Wed, 23 December 2015 15:28
|
|
|
Re: [GMCnet] Setting the front ride height procedure
By: Harry on Wed, 23 December 2015 15:46
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
By: USAussie on Thu, 24 December 2015 16:18
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
By: Larry on Thu, 24 December 2015 13:54
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
By: USAussie on Mon, 18 January 2016 17:44
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
By: USAussie on Mon, 18 January 2016 19:34
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
By: USAussie on Mon, 18 January 2016 22:51
|
|
|
Re: Setting the front ride height procedure
|
|
|
Re: Setting the front ride height procedure
|
|
|
Re: Setting the front ride height procedure
By: Larry on Wed, 23 December 2015 17:32
|
|
|
Re: Setting the front ride height procedure
|
|
|
Re: Setting the front ride height procedure
|
|
|
Re: Setting the front ride height procedure
By: Larry on Wed, 23 December 2015 19:20
|
|
|
Re: Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: Setting the front ride height procedure
By: JohnL455 on Mon, 18 January 2016 17:56
|
Goto Forum:
Current Time: Fri Sep 27 13:36:38 CDT 2024
Total time taken to generate the page: 0.00926 seconds
|