Home » Public Forums » GMCnet » Setting the front ride height procedure
Re: [GMCnet] Setting the front ride height procedure [message #292840 is a reply to message #292834] |
Wed, 23 December 2015 20:33 |
James Hupy
Messages: 6806 Registered: May 2010
Karma:
|
Senior Member |
|
|
It is not the bolt on the tool. It will be the pork chop adjusting bolt and
nut that lives in the cross member where the pork chop is located. I
personally have replaced too many of them to count. No doubt stripped by
well intentioned but misinformed or uninformed people who were not using a
torsion bar unloader tool. Yes, lift the coach, install the unloader tool,
tension the center bolt until the bolt in the cross member can be moved
freely with the nut. Then, and only after you have soaked them in your
favorite perpetrating medium, remove the bolt and nut, clean up the
threads, coat the entire length of the bolt with never-seez, and replace
the nut and bolt. Take 3 turns on the center bolt of the unloader tool,
then tighten the adjusting bolt. Remove the unloader tool, lower the coach,
drive it for 8 or 10 miles, then check ride heights front and rear. Repeat
as needed.
Jim Hupy
Salem, Or
On Dec 23, 2015 5:52 PM, "Scott Nutter" wrote:
> OhOk. Thanks Larry! Now it makes sense. The bolt in guestion that will
> strip is the bolt on the tool. Why doesn't the shop manual mention this in
> their step by step instructions?
> --
> Scott Nutter
> 1978 455 Royale Center Kitchen, Quad bags.
> Houston, Texas
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
|
|
Setting the front ride height procedure
|
|
|
Re: Setting the front ride height procedure
By: Harry on Wed, 23 December 2015 15:18
|
|
|
Re: [GMCnet] Setting the front ride height procedure
By: jimk on Wed, 23 December 2015 15:28
|
|
|
Re: [GMCnet] Setting the front ride height procedure
By: Harry on Wed, 23 December 2015 15:46
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
By: USAussie on Thu, 24 December 2015 16:18
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
By: Larry on Thu, 24 December 2015 13:54
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
By: USAussie on Mon, 18 January 2016 17:44
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
By: USAussie on Mon, 18 January 2016 19:34
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
By: USAussie on Mon, 18 January 2016 22:51
|
|
|
Re: Setting the front ride height procedure
|
|
|
Re: Setting the front ride height procedure
|
|
|
Re: Setting the front ride height procedure
By: Larry on Wed, 23 December 2015 17:32
|
|
|
Re: Setting the front ride height procedure
|
|
|
Re: Setting the front ride height procedure
|
|
|
Re: Setting the front ride height procedure
By: Larry on Wed, 23 December 2015 19:20
|
|
|
Re: Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: [GMCnet] Setting the front ride height procedure
|
|
|
Re: Setting the front ride height procedure
By: JohnL455 on Mon, 18 January 2016 17:56
|
Goto Forum:
Current Time: Fri Sep 27 14:09:25 CDT 2024
Total time taken to generate the page: 0.01117 seconds
|