|
Re: quick question [message #284859 is a reply to message #284857] |
Fri, 14 August 2015 10:15 |
Bullitthead
Messages: 1411 Registered: November 2013
Karma: 5
|
Senior Member |
|
|
Just a few days ago:
http://gmc.mybirdfeeder.net/GMCforum/index.php?t=msg&goto=282688&rid=0&srch=spindle+nut#msg_282688
"I suspect that most spindle failures result from improper tensioning of the
wheel bearings. Yes, the castellated nut plays a part in that, but the GMC
is a bit different in the tensioning proceedure. Follow the Manual EXACTLY
and you will seldom have a problem. Use a torque wrench. You do have one,
don't you? While turning the drum by hand, torque the spindle nut to 25
foot pounds. Then, loosen the nut 1/2 turn. Using only your fingers,
tighten the nut until resistance is felt. Look and see if the cotter pin
hole in the spindle aligns with a slot in the nut. If it aligns, put a new
cotter pin through the nut and spindle and spread the end. If it DOES NOT
align, LOOSEN the nut until it aligns. Remember this. Hub and drum
assemblies expand when heated, spindles not as much. This takes up the
slack in the assembly. If you start out too tight, when the parts are at
normal operating temperature, you won't have enough clearance and, trust
me, bad stuff will happen, and sooner rather than later."
Jim Hupy
Salem, Or
78 GMC ROYALE 403
Terry Kelpien
ASE Master Technician
73 Glacier 260
Smithfield, Va.
|
|
|
Re: [GMCnet] quick question [message #284865 is a reply to message #284859] |
Fri, 14 August 2015 10:43 |
Mr ERFisher
Messages: 7117 Registered: August 2005
Karma: 2
|
Senior Member |
|
|
And be sure you have the right seal
On Friday, August 14, 2015, Terry wrote:
> Just a few days ago:
>
>
> http://gmc.mybirdfeeder.net/GMCforum/index.php?t=msg&goto=282688&rid=0&srch=spindle+nut#msg_282688
> "I suspect that most spindle failures result from improper tensioning of
> the
> wheel bearings. Yes, the castellated nut plays a part in that, but the GMC
> is a bit different in the tensioning proceedure. Follow the Manual EXACTLY
> and you will seldom have a problem. Use a torque wrench. You do have one,
> don't you? While turning the drum by hand, torque the spindle nut to 25
> foot pounds. Then, loosen the nut 1/2 turn. Using only your fingers,
> tighten the nut until resistance is felt. Look and see if the cotter pin
> hole in the spindle aligns with a slot in the nut. If it aligns, put a new
> cotter pin through the nut and spindle and spread the end. If it DOES NOT
> align, LOOSEN the nut until it aligns. Remember this. Hub and drum
> assemblies expand when heated, spindles not as much. This takes up the
> slack in the assembly. If you start out too tight, when the parts are at
> normal operating temperature, you won't have enough clearance and, trust
> me, bad stuff will happen, and sooner rather than later."
>
> Jim Hupy
> Salem, Or
> 78 GMC ROYALE 403
> --
> Terry Kelpien
> ASE Master Technician
> 73 Glacier 260
> Smithfield, Va.
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
--
Gene Fisher -- 74-23,77PB/ore/ca
“Give a man a fish; you have fed him for today --- give him a URL and
-------
http://gmcmotorhome.info/
Alternator Protection Cable
http://gmcmotorhome.info/APC.html
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
|
|
|
|