Any Mondello CAM Tests? [message #281251] |
Thu, 02 July 2015 08:01 |
dr.diesel
Messages: 85 Registered: April 2015 Location: The Haute, Indiana
Karma: 0
|
Member |
|
|
This winter I'll be doing the timing chain and aluminum intake swap. Heck with that much apart swapping in a new cam would be easy work.
Anyone done the Mondello cam swap, any dyno or opinions/mileage on the results?
77 Kingsley
|
|
|
|
Re: Any Mondello CAM Tests? [message #281281 is a reply to message #281269] |
Thu, 02 July 2015 11:28 |
Keith V
Messages: 2337 Registered: March 2008 Location: Mounds View,MN
Karma: 0
|
Senior Member |
|
|
hal kading wrote on Thu, 02 July 2015 10:29I'd go with the Jim Bounds Kryptonite cam if I was going to change one.
Hal Kading 78 Buskirk Las Cruces NM
I wouldn't buy anything from Mondello, esp a cam.
It's probablly a race cam not an RV cam.
Jim B has a really nice flat tappet cam and a nicer roller cam
Either one will make you happy.
I have the flat tappet cam...
Keith Vasilakes
Mounds View. MN
75 ex Royale GMC
ask me about MicroLevel
Cell, 763-732-3419
My427v8@hotmail.com
|
|
|
Re: Any Mondello CAM Tests? [message #281286 is a reply to message #281251] |
Thu, 02 July 2015 11:41 |
dr.diesel
Messages: 85 Registered: April 2015 Location: The Haute, Indiana
Karma: 0
|
Member |
|
|
Thanks Guys, a couple of the GMC only sites recommend the Mondello CAM (they have two RV grinds), and JimB's site is kinda a mess, even after extensive searching I missed is offering!
Glad I asked thanks to all.
77 Kingsley
|
|
|
Re: Any Mondello CAM Tests? [message #281294 is a reply to message #281286] |
Thu, 02 July 2015 12:11 |
roy1
Messages: 2126 Registered: July 2004 Location: Minden nevada
Karma: 6
|
Senior Member |
|
|
[quote title=dr.diesel wrote on Thu, 02 July 2015 09:41]Thanks Guys, a couple of the GMC only sites recommend the Mondello CAM (they have two RV grinds), and JimB's site is kinda a mess, even after extensive searching I missed is offering!
Glad I asked thanks to all.[/quo
You could also ask Dick Paterson his choice he suggested a nice high torque flat cam that worked real well for me from comp cams..
Roy Keen
Minden,NV
76 X Glenbrook
|
|
|
Re: [GMCnet] Any Mondello CAM Tests? [message #281305 is a reply to message #281286] |
Thu, 02 July 2015 13:15 |
powerjon
Messages: 2446 Registered: January 2004
Karma: 5
|
Senior Member |
|
|
Andy,
Go Here: http://www.gmccoop.com/koba_built_motors.htm scroll down to: “Best parts for the job and the build” and then you will see the information on the cams for both motors and is even available for the Cad motor.
JR Wright
GMC Great Laker MHC
GMC Eastern States
GMCGL Tech Editor
GMCMHI
78 GMC Buskirk 30’ Stretch
1975 GMC Avion (Under Reconstruction)
Michigan
> On Jul 2, 2015, at 12:41 PM, Andy wrote:
>
> Thanks Guys, a couple of the GMC only sites recommend the Mondello CAM (they have two RV grinds), and JimB's site is kinda a mess, even after
> extensive searching I missed is offering!
>
> Glad I asked thanks to all.
> --
> 77 Kingsley
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
J.R. Wright
GMC GreatLaker
GMC Eastern States
GMCMI
78 30' Buskirk Stretch
75 Avion Under Reconstruction
Michigan
|
|
|
Re: Any Mondello CAM Tests? [message #281312 is a reply to message #281251] |
Thu, 02 July 2015 14:34 |
Chris Tyler
Messages: 458 Registered: September 2013 Location: Odessa FL
Karma: 7
|
Senior Member |
|
|
Going back a while, as I recall Jim B spent a lot of time on R and D on the cam specs, and those are now availible in the Comp catalog much to his resentment. I also seem to recall he does not sell the roller cam apart from the engine package due to modifications needed
One problem I heard of is machining the underside of the stock style recessed manifold to clear the roller tappets.
I do think he sells the flat tappet cam separately, and it would be good to get it from him if you can. Comp isnt hurting for business
He is a big proponeant of running rollers these days. But it is expensive up front when you cant use OEM parts like fords or chevys
looking at the Mondello RV grinds, they should work fine
Apparantly, my winterfeldt engine runs a melling cam that works well and is inexpensive
76 Glenbrook
|
|
|