Home » Public Forums » GMCnet » Onan flywheel removal
Onan flywheel removal [message #278491] |
Wed, 27 May 2015 06:10 |
Tilerpep
Messages: 404 Registered: June 2013 Location: Raleigh, NC
Karma: 7
|
Senior Member |
|
|
Trying to remove flywheel on Onan yesterday to fix/replace my starter bracket...
Found this thread
http://gmc.mybirdfeeder.net/GMCforum/index.php?t=msg&goto=176648&rid=3615&srch=onan+flywheel+bolt#msg_176648
I got a HF puller set (not the one Jon recommends, but other threads did) and the bolts did not seem right to set in the flywheel. Jon mentions buying 3/8 bolts in his thread, but I tried 16 thread and 24 thread, and 24 is definitely not it, and the 16 will only seat about three or four threads in. I am nervous driving it in too hard, because the flywheel metal has already pocked a bit on the first attempts. As in, pulled the first thread or two out.
And, assuming I can get a good bite into the flywheel, can I use my impact driver to turn the puller bolt? I have read to never use the impact putting the flywheel back on, but I don't see how to hold the flywheel from spinning and turn the puller bolt while getting it off.
All advice welcome. Thanks.
1975 Glenbrook, 1978 Royale rear bath
Raleigh, NC
|
|
|
Re: Onan flywheel removal [message #278495 is a reply to message #278491] |
Wed, 27 May 2015 07:27 |
lqqkatjon
Messages: 2324 Registered: October 2010 Location: St. Cloud, MN
Karma: 5
|
Senior Member |
|
|
I am almost certain those are course thread grade 8 bolts that I used.
with that particular puller I did not use any impact wrench. I think I just used my ratchet wrenches, it came off almost instantly. That puller must assert the right force in the correct place.
I am not sure what harbor freight one you used, but I remember the one I bought from Oreily's made the job simple.
Jon Roche
75 palm beach
EBL EFI, manny headers, Micro Level, rebuilt most of coach now.
St. Cloud, MN
http://lqqkatjon.blogspot.com/
|
|
|
Re: [GMCnet] Onan flywheel removal [message #278502 is a reply to message #278495] |
Wed, 27 May 2015 08:03 |
Jim Miller
Messages: 501 Registered: March 2008
Karma: 10
|
Senior Member |
|
|
It might not be a bad idea to chase the flywheel’s threads with a tap before screwing in the puller bolts and it wouldn’t be a bad idea to apply a liberal dose of anti-sieze compound on the puller’s jack bolt before attempting the operation. I often use an impact wrench on pullers - but I start out with a reduced amount of impact force and then work my way up if necessary. I’ve also been known to apply firm pressure with the puller and then tap the end of the puller bolt with a lead or bronze hammer in order to break tapers loose.
--Jim "saving the lives of Onans...one unit at a time" Miller
1977 Eleganza II
1977 Royale
Hamilton, OH
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Jim Miller
1977 Eleganza II
1977 Royale
Hamilton, OH
|
|
|
Re: Onan flywheel removal [message #278515 is a reply to message #278491] |
Wed, 27 May 2015 09:45 |
|
Matt Colie
Messages: 8547 Registered: March 2007 Location: S.E. Michigan
Karma: 7
|
Senior Member |
|
|
Tyler,
Listen to Jim Miller. Chase the puller threads.
Any lubrication on the puller threads will help it work.
I have never needed an impact pulling a flywheel, but if you take it up the ratchet load and give it a shot with a light hammer, that usually works on Onan flywheels.
WORD OF CAUTION about installing the flywheel.
BELIEVE the torque in the manual. There are more than a few Onans with cracked flywheels. Anytime someone gets too heavy with the retaining force - SNAP.
Matt
Tilerpep wrote on Wed, 27 May 2015 07:10Trying to remove flywheel on Onan yesterday to fix/replace my starter bracket...
Found this thread
http://gmc.mybirdfeeder.net/GMCforum/index.php?t=msg&goto=176648&rid=3615&srch=onan+flywheel+bolt#msg_176648
I got a HF puller set (not the one Jon recommends, but other threads did) and the bolts did not seem right to set in the flywheel. Jon mentions buying 3/8 bolts in his thread, but I tried 16 thread and 24 thread, and 24 is definitely not it, and the 16 will only seat about three or four threads in. I am nervous driving it in too hard, because the flywheel metal has already pocked a bit on the first attempts. As in, pulled the first thread or two out.
And, assuming I can get a good bite into the flywheel, can I use my impact driver to turn the puller bolt? I have read to never use the impact putting the flywheel back on, but I don't see how to hold the flywheel from spinning and turn the puller bolt while getting it off.
All advice welcome. Thanks.
Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL, GMCES
Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum Brakes with Applied Control Arms
SE Michigan - Near DTW - Twixt A2 and Detroit
|
|
|
|
|
Re: Onan flywheel removal [message #278586 is a reply to message #278491] |
Wed, 27 May 2015 21:48 |
Tilerpep
Messages: 404 Registered: June 2013 Location: Raleigh, NC
Karma: 7
|
Senior Member |
|
|
Progress...rented a tap and die set, made easy work of setting the pull bolts.
Picked up a timing gear puller, but did not like how the taper went into the center. This was the kit I already had bought at HF
http://www.harborfreight.com/bolt-type-wheel-puller-set-69889.html
and it had a flat, round pressure point that fit perfect. The rig proved strong enough. I did use my impact because motor would spin as I tried to turn bolt. Snugged it, nothing to lose (I lied to myself), a little more air, and a pleasant pinging POP and it was free.
So next questions into the Onan, not sure if warrant another thread -
the starter bracket is broken, and clearly has been sitting on the frame and actually worn the bracket and lower bolt smooth. I am installing new mount cushions but if they are not enough to raise it clear, is there a way to adjust the overall height of the onan in/on the slides?
If I use my cheap HF welder to put my bracket back together will it hold? I am aware of replacements for about $50, but I want to play/learn my welder, and I would like it back together tomorrow. This metal almost looks crumbly to begin with.
And...took the choke off and multiple parts fell out of it. Can't find any pictures of the mechanism on forum or pic site. It looked like a hinge pin was missing off one side, any photos available showing the moving parts that go against the exhaust manifold?
While I am at it, I'll post another thing others may need to look for that was out of sight - I have a fiberglass mat like something for insulation in the gen compartment. It is falling apart/down. when I pulled some covers to clean mud daubers out of the cooling fins, realized that the hair like stuff had been sucked in and packed the back side of one cylinder nearly completely blocking air flow. If you have this hair mat stuff, check it out. To replace that, is there a fireproof, metal backed insulation that I can get at Home Depot or the like?
1975 Glenbrook, 1978 Royale rear bath
Raleigh, NC
|
|
|
Re: [GMCnet] Onan flywheel removal [message #278591 is a reply to message #278586] |
Wed, 27 May 2015 23:58 |
|
USAussie
Messages: 15912 Registered: July 2007 Location: Sydney, Australia
Karma: 6
|
Senior Member |
|
|
Tyler,
Don't bother with welding the Onan starter bracket it's only going to break again unless you're real good welder.
Just get one of these:
http://www.appliedgmc.com/prod.itml/icOid/812
Regards,
Rob M.
The Pedantic Mechanic
Sydney, Australia
AUS '75 Avion - The Blue Streak TZE365V100428
USA '75 Avion - Double Trouble TZE365V100426
-----Original Message-----
From: Gmclist [mailto:gmclist-bounces@temp.gmcnet.org] On Behalf Of Tyler
Sent: Thursday, May 28, 2015 12:49 PM
To: gmclist@temp.gmcnet.org
Subject: Re: [GMCnet] Onan flywheel removal
Progress...rented a tap and die set, made easy work of setting the pull bolts.
Picked up a timing gear puller, but did not like how the taper went into the center. This was the kit I already had bought at HF
http://www.harborfreight.com/bolt-type-wheel-puller-set-69889.html
and it had a flat, round pressure point that fit perfect. The rig proved strong enough. I did use my impact because motor would spin
as I tried to turn bolt. Snugged it, nothing to lose (I lied to myself), a little more air, and a pleasant pinging POP and it was
free.
So next questions into the Onan, not sure if warrant another thread - the starter bracket is broken, and clearly has been sitting on
the frame and actually worn the bracket and lower bolt smooth. I am installing new mount cushions but if they are not enough to
raise it clear, is there a way to adjust the overall height of the onan in/on the slides?
If I use my cheap HF welder to put my bracket back together will it hold? I am aware of replacements for about $50, but I want to
play/learn my welder, and I would like it back together tomorrow. This metal almost looks crumbly to begin with.
And...took the choke off and multiple parts fell out of it. Can't find any pictures of the mechanism on forum or pic site. It looked
like a hinge pin was missing off one side, any photos available showing the moving parts that go against the exhaust manifold?
While I am at it, I'll post another thing others may need to look for that was out of sight - I have a fiberglass mat like something
for insulation in the gen compartment. It is falling apart/down. when I pulled some covers to clean mud daubers out of the cooling
fins, realized that the hair like stuff had been sucked in and packed the back side of one cylinder nearly completely blocking air
flow. If you have this hair mat stuff, check it out.
To replace that, is there a fireproof, metal backed insulation that I can get at Home Depot or the like?
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Regards,
Rob M. (USAussie)
The Pedantic Mechanic
Sydney, Australia
'75 Avion - AUS - The Blue Streak TZE365V100428
'75 Avion - USA - Double Trouble TZE365V100426
|
|
|
|
Re: [GMCnet] Onan flywheel removal [message #283677 is a reply to message #278594] |
Sat, 01 August 2015 17:07 |
Terrasmak
Messages: 40 Registered: December 2014 Location: Las Vegas
Karma: 0
|
Member |
|
|
I checked out the above link, I have a loose started bracket. Made the pIunge and bought the aftermarket one, I just need to get the flywheel
Off now. Any links to the correct puller ?
Len Novak, 76 Eleganza II, Las Vegas
|
|
|
|
|
Re: [GMCnet] Onan flywheel removal [message #283763 is a reply to message #283703] |
Sun, 02 August 2015 16:11 |
Terrasmak
Messages: 40 Registered: December 2014 Location: Las Vegas
Karma: 0
|
Member |
|
|
Well it's off, used a harmonic balancer puller from autozone ($20 don't think I'm returning the rental ) and I think I already have the upgraded bracket. All 3 bolts were loose, the bottom bolt thru the muffler bracket the threads are stripped. Time for a heli coil , a little sheet metal hardware to replace a could missing bolts and back together. The oil pressure/filter housing was pretty loose , tightened it and got a lot of crud out from the cooling fins.
I have a feeling the spare bracket is going on my dads coach next time I head home to see him.
Len Novak, 76 Eleganza II, Las Vegas
|
|
|
Re: [GMCnet] Onan flywheel removal [message #283785 is a reply to message #283763] |
Sun, 02 August 2015 19:51 |
|
ljdavick
Messages: 3548 Registered: March 2007 Location: Fremont, CA
Karma: -3
|
Senior Member |
|
|
I had the same feeling when I installed the ragusa bracket. I didn’t see anything wrong with the one I was removing, but since I had the new one I installed it. The starter motor has always engaged perfectly since, so I feel as if I made the right choice.
Larry Davick
A Mystery Machine
1976(ish) Palm Beach
Fremont, CA
> On Aug 2, 2015, at 2:11 PM, Len Novak wrote:
>
> Well it's off, used a harmonic balancer puller from autozone ($20 don't think I'm returning the rental ) and I think I already have the upgraded
> bracket. All 3 bolts were loose, the bottom bolt thru the muffler bracket the threads are stripped. Time for a heli coil , a little sheet metal
> hardware to replace a could missing bolts and back together. The oil pressure/filter housing was pretty loose , tightened it and got a lot of crud out
> from the cooling fins.
>
>
> I have a feeling the spare bracket is going on my dads coach next time I head home to see him.
> --
> Len Novak, 76 Eleganza II, Las Vegas
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
Larry Davick
A Mystery Machine
1976(ish) Palm Beach
Fremont, Ca
Howell EFI + EBL + Electronic Dizzy
|
|
|
|
Goto Forum:
Current Time: Sun Sep 29 02:30:11 CDT 2024
Total time taken to generate the page: 0.01250 seconds
|