Water heat remove and replace [message #278198] |
Fri, 22 May 2015 12:22 |
Chuck and Lureen
Messages: 16 Registered: April 2013 Location: West Michigan
Karma: 0
|
Junior Member |
|
|
My wet bath 1975 Glenbrook has a leaky water heater. It's the 6 gal Attwood rectangular, electric and coolant heat exchanger type. I have a replacement unit and the original unit completely disconnected and everything cleared from under the bathroom sink, but there doesn't seem to be enough space under there to get it out. What am I missing? I thought that the heater would tip up, then down and out, but I can't figure it out. I need some pointers or direction as to what needs to be done. Thanks in advance
Chuck and Lureen Mullally
West Michigan
1975 Glenbrook
|
|
|
Re: [GMCnet] Water heat remove and replace [message #278204 is a reply to message #278198] |
Fri, 22 May 2015 16:13 |
emerystora
Messages: 4442 Registered: January 2004
Karma: 13
|
Senior Member |
|
|
Chuck
If this is an old Atwood rectangular unit you might find some help at
GMCMI.COM
Click on The GMC Motorhome and then on the drop down menu Technical Seminar Handouts, then click on Bathrooms.
There is a very old article on the removal.
Emery Stora
77 Kingsley
Frederick, CO
> On May 22, 2015, at 11:22 AM, Chuck Mullally wrote:
>
> My wet bath 1975 Glenbrook has a leaky water heater. It's the 6 gal Attwood rectangular, electric and coolant heat exchanger type. I have a
> replacement unit and the original unit completely disconnected and everything cleared from under the bathroom sink, but there doesn't seem to be
> enough space under there to get it out. What am I missing? I thought that the heater would tip up, then down and out, but I can't figure it out. I
> need some pointers or direction as to what needs to be done. Thanks in advance
> --
> Chuck and Lureen Mullally
> West Michigan
> 1975 Glenbrook
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
Re: Water heat remove and replace [message #278227 is a reply to message #278198] |
Sat, 23 May 2015 08:33 |
Tilerpep
Messages: 404 Registered: June 2013 Location: Raleigh, NC
Karma: 7
|
Senior Member |
|
|
I have a 75 Glenbrook, and just changed mine out two months ago. There were two heavy metal straps over the heater that hooked on the exterior side of the platform the heater sat on, and had eyebolts on the interior side - got both of those off? I pulled my whole bath rear wall (removed rear cabinet, fold down seats, etc.) off and went that route. My new water heater had different mounts on the ends, and was just a little too wide to reuse the over straps, so having the back wall off made securing it possible. My biggest problem was finding connectors for all the wacky sizes of heater and old plumbing. My next biggest problem was getting the air out of the engine coolant lines once it was all back together. If you don't have a filler built into the cab heater line (up high in front of radiator), I would suggest unhooking the rear engine to bath supply line and beginning your coolant refill from there (fill towards the bath). Put the rear line back on the engine when full, then fill at radiator. Then run engine just long enough to get the thermostat open for a minute or two, then let it sit with a full overflow reservoir. Repeat the engine run cool off cycle again the next day and refill reservoir. JWIWD
1975 Glenbrook, 1978 Royale rear bath
Raleigh, NC
|
|
|
Re: [GMCnet] Water heat remove and replace [message #278436 is a reply to message #278198] |
Tue, 26 May 2015 09:55 |
Len Novak
Messages: 676 Registered: February 2004 Location: Las Vegas, NV
Karma: -3
|
Senior Member |
|
|
Pull the frame that houses the sliding doors. I believe they are held on
with several screws around the frame.
Len and Pat Novak
1978 GMC Kingsley
The Beast II with dash lights that work and labels you can see!
Fallbrook, CA new email: B52Rule@Roadrunner.Com
http://www.gmcmhphotos.com/photos/showgallery.php?cat=4375
www.bdub.net/novak/
-----Original Message-----
From: Gmclist [mailto:gmclist-bounces@temp.gmcnet.org] On Behalf Of Chuck
Mullally
Sent: Friday, May 22, 2015 10:23 AM
To: gmclist@temp.gmcnet.org
Subject: [GMCnet] Water heat remove and replace
My wet bath 1975 Glenbrook has a leaky water heater. It's the 6 gal Attwood
rectangular, electric and coolant heat exchanger type. I have a replacement
unit and the original unit completely disconnected and everything cleared
from under the bathroom sink, but there doesn't seem to be enough space
under there to get it out. What am I missing? I thought that the heater
would tip up, then down and out, but I can't figure it out. I need some
pointers or direction as to what needs to be done. Thanks in advance
--
Chuck and Lureen Mullally
West Michigan
1975 Glenbrook
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Len and Pat Novak
1978 GMC Kingsley
The Beast II with dash lights that work and labels you can see!
Las Vegas, NV new email: B52sRule@Gmail.com
http://www.gmcmhphotos.com/photos/showgallery.php?cat=4375
www.bdub.net/novak/
|
|
|