GMCforum
For enthusiast of the Classic GMC Motorhome built from 1973 to 1978. A web-based mirror of the GMCnet mailing list.

Home » Public Forums » GMCnet » Split Boot Installation
Split Boot Installation [message #269563] Tue, 13 January 2015 09:51 Go to next message
tphipps is currently offline  tphipps   United States
Messages: 3005
Registered: August 2004
Location: Spanish Fort, AL
Karma: 9
Senior Member
Dorman # 03609 Speedi-Boot. I got mine at O'Reilly's. Probably get it from any of the auto parts stores, except NAPA. Cost is less than $20. Should have enough change to buy a senior coffee at McD's.
Although I would hate to do the change over along side the road, I think it would be a good addition to spares on board the coach. I'm going to get another one, just for that reason.
The fit of the boot is exact duplicate of the original, with a few more folds. May resist tearing better. Material seems more flexible. The tiny bolts and nuts are a bit difficult to deal with, nut size is 1/4". I used a small open end wrench to hold it, socket would not fit in the space available. You also need a #1 sized Philip screwdriver to turn the bolt. The instructions say to grease the bolts to ease installation. Without greasing the bolt, I was unable to overcome the friction between the rubber hole and the bolt. You also need to have an awl or small nail to make sure the molded holes go all the way through the rubber flange.
The package includes a packet of CV grease, enough to do the job. I used brake free degreaser to clean out the old grease, as recommended by the instructions. You might get a package of the thin nitrate gloves, the grease is very messy and sticks to everything.
Banding material, for both ends, is included in the package. It will not be enough to double-band the big end, but will clamp it on tight.
I removed the front wheel, really makes the job easier. Also had the wheel well liner out and removed the oil filter. Turns out, neither of these two removals were necessary.
Now, back to the headliner job.
Hope this helps someone.
Tom, MS II


2012 Phoenix Cruiser model 2552 KA4CSG
Re: [GMCnet] Split Boot Installation [message #269571 is a reply to message #269563] Tue, 13 January 2015 10:37 Go to previous messageGo to next message
Mr ERFisher is currently offline  Mr ERFisher   United States
Messages: 7117
Registered: August 2005
Karma: 2
Senior Member
Shoe gue works better

On Tuesday, January 13, 2015, Thomas Phipps wrote:

> Dorman # 03609 Speedi-Boot. I got mine at O'Reilly's. Probably get it
> from any of the auto parts stores, except NAPA. Cost is less than $20.
> Should have enough change to buy a senior coffee at McD's.
> Although I would hate to do the change over along side the road, I think
> it would be a good addition to spares on board the coach. I'm going to get
> another one, just for that reason.
> The fit of the boot is exact duplicate of the original, with a few more
> folds. May resist tearing better. Material seems more flexible. The tiny
> bolts and nuts are a bit difficult to deal with, nut size is 1/4". I used
> a small open end wrench to hold it, socket would not fit in the space
> available. You also need a #1 sized Philip screwdriver to turn the bolt.
> The instructions say to grease the bolts to ease installation. Without
> greasing the bolt, I was unable to overcome the friction between the
> rubber hole and the bolt. You also need to have an awl or small nail to
> make
> sure the molded holes go all the way through the rubber flange.
> The package includes a packet of CV grease, enough to do the job. I used
> brake free degreaser to clean out the old grease, as recommended by the
> instructions. You might get a package of the thin nitrate gloves, the
> grease is very messy and sticks to everything.
> Banding material, for both ends, is included in the package. It will not
> be enough to double-band the big end, but will clamp it on tight.
> I removed the front wheel, really makes the job easier. Also had the
> wheel well liner out and removed the oil filter. Turns out, neither of
> these
> two removals were necessary.
> Now, back to the headliner job.
> Hope this helps someone.
> Tom, MS II
> --
> 1975 GMC Avion
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>


--
Gene Fisher -- 74-23,77PB/ore/ca
“Give a man a fish; you have fed him for today --- give him a URL and
-------
http://gmcmotorhome.info/
Alternator Protection Cable
http://gmcmotorhome.info/APC.html
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Re: Split Boot Installation [message #269572 is a reply to message #269563] Tue, 13 January 2015 10:44 Go to previous messageGo to next message
Matt Colie is currently offline  Matt Colie   United States
Messages: 8547
Registered: March 2007
Location: S.E. Michigan
Karma: 7
Senior Member
About the Dorman Split boot...

I have helped Nick Chapeckis install two of these. The first was over two years, but not a lot of miles in GMC terms. They do seem to be effective and much easier than removing the drive axle to change the boot out.

Matt


Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL, GMCES
Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum Brakes with Applied Control Arms
SE Michigan - Near DTW - Twixt A2 and Detroit
Re: [GMCnet] Split Boot Installation [message #269578 is a reply to message #269571] Tue, 13 January 2015 12:26 Go to previous messageGo to next message
Otterwan   United States
Messages: 946
Registered: July 2013
Location: Lynnwood (north of Seattl...
Karma: 0
Senior Member
Mr ERFisher wrote on Tue, 13 January 2015 08:37
Shoe gue works better


Good information, thanks! Gene, what part of this process are you recommending Shoe Goo for?


1977 Birchaven, Lynnwood WA - "We may not be able to stop all evil in the world, but I know that how we treat one another is entirely up to us."
Re: [GMCnet] Split Boot Installation [message #269593 is a reply to message #269578] Tue, 13 January 2015 13:24 Go to previous messageGo to next message
Kingsley Coach is currently offline  Kingsley Coach   United States
Messages: 2691
Registered: March 2009
Location: Nova Scotia Canada
Karma: -34
Senior Member
Tom

I just ordered one. A man can't have enough spare parts..
Thanks

Mike in NS

On Tue, Jan 13, 2015 at 2:26 PM, David Orders wrote:

> Mr ERFisher wrote on Tue, 13 January 2015 08:37
>> Shoe gue works better
>
>
> Good information, thanks! Gene, what part of this process are you
> recommending Shoe Goo for?
>
> --
> 1976 Royale "Twinkie II" Lynnwood WA - "We may not be able to stop all
> evil in the world, but I know that how we treat one another is entirely up
> to
> us."
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>



--
Michael Beaton
1977 Kingsley 26-11
1977 Eleganza II 26-3
Antigonish, NS

I am not an alcoholic; alcoholics go to meetings.
I am a drunk; I go to parties !
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

Re: Split Boot Installation [message #269596 is a reply to message #269563] Tue, 13 January 2015 13:41 Go to previous messageGo to next message
Otterwan   United States
Messages: 946
Registered: July 2013
Location: Lynnwood (north of Seattl...
Karma: 0
Senior Member
tphipps wrote on Tue, 13 January 2015 07:51
Dorman # 03609 Speedi-Boot. I got mine at O'Reilly's.


How did you come up with the part number? For a 1976 Toronado O'Reilly says 03608 would be the correct boot.


1977 Birchaven, Lynnwood WA - "We may not be able to stop all evil in the world, but I know that how we treat one another is entirely up to us."
Re: [GMCnet] Split Boot Installation [message #269598 is a reply to message #269596] Tue, 13 January 2015 13:55 Go to previous messageGo to next message
Kingsley Coach is currently offline  Kingsley Coach   United States
Messages: 2691
Registered: March 2009
Location: Nova Scotia Canada
Karma: -34
Senior Member
David
03608 seems to be for a lot of Toyota products.
03609 fits caddy eldorado
Mike

On Tue, Jan 13, 2015 at 3:41 PM, David Orders wrote:

> tphipps wrote on Tue, 13 January 2015 07:51
>> Dorman # 03609 Speedi-Boot. I got mine at O'Reilly's.
>
>
> How did you come up with the part number? For a 1976 Toronado O'Reilly
> says 03608 would be the correct boot.
>
> --
> 1976 Royale "Twinkie II" Lynnwood WA - "We may not be able to stop all
> evil in the world, but I know that how we treat one another is entirely up
> to
> us."
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>



--
Michael Beaton
1977 Kingsley 26-11
1977 Eleganza II 26-3
Antigonish, NS

I am not an alcoholic; alcoholics go to meetings.
I am a drunk; I go to parties !
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

Re: [GMCnet] Split Boot Installation [message #269600 is a reply to message #269598] Tue, 13 January 2015 14:30 Go to previous messageGo to next message
Otterwan   United States
Messages: 946
Registered: July 2013
Location: Lynnwood (north of Seattl...
Karma: 0
Senior Member
Just ran the search again, and still get 03608 for both Toronada and Caddy. Oh well.

http://www.oarsllc.com/Capture.JPG

http://www.oarsllc.com/Capture.JPG


1977 Birchaven, Lynnwood WA - "We may not be able to stop all evil in the world, but I know that how we treat one another is entirely up to us."
Re: [GMCnet] Split Boot Installation [message #269603 is a reply to message #269593] Tue, 13 January 2015 14:48 Go to previous messageGo to next message
Ken Henderson is currently offline  Ken Henderson   United States
Messages: 8726
Registered: March 2004
Location: Americus, GA
Karma: 9
Senior Member
Wanna bet? You should see my shop, sea-land container, and my aunt's farm
barn! That's the REAL reason I unbalanced -- from worrying about what my
son will do with all my STUFF!

Ken H.


On Tue, Jan 13, 2015 at 2:24 PM, Kingsley Coach
wrote:

> Tom
>
> I just ordered one. A man can't have enough spare parts..
> Thanks
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist



Ken Henderson
Americus, GA
www.gmcwipersetc.com
Large Wiring Diagrams
76 X-Birchaven
76 X-Palm Beach
Re: Split Boot Installation [message #269607 is a reply to message #269596] Tue, 13 January 2015 15:59 Go to previous messageGo to next message
nchapekis is currently offline  nchapekis   United States
Messages: 165
Registered: February 2004
Location: Ypsilanti, MI
Karma: 0
Senior Member
Otterwan wrote on Tue, 13 January 2015 14:41
How did you come up with the part number? For a 1976 Toronado O'Reilly says 03608 would be the correct boot.


Try this: Dorman universal fit (part # 614-003)

I got a new boot for one side, then a rebuilt CV joint and boot for the other side, both from Jim Kanomata a few years back. The CV joint was fine, however neither of the boots lasted very long. Both were replaced by Dorman split boots, which are still good, although as Matt mentioned, our coach doesn't get high usage (proabably average usage for non-retirees though).


Nick Chapekis
Ypsilanti, MI
former owner - 78 Kingsley
Re: [GMCnet] Split Boot Installation [message #269616 is a reply to message #269607] Tue, 13 January 2015 16:37 Go to previous messageGo to next message
USAussie is currently offline  USAussie   United States
Messages: 15912
Registered: July 2007
Location: Sydney, Australia
Karma: 6
Senior Member
G'day,

This is for Newbies.

YEARS ago there were boots made of silicone available for the GMC; they were colored blue and were called "blue boots" (how's that
for demonstrating an acute grasp on the obvious) unfortunately they are no longer manufactured as they are virtually indestructible!


I had the good fortune of obtaining a pair from a gentleman here on the GMCnet and one extra from a second gentleman here. The pair
was installed on The Blue Streak and the spare is held here as well. In the USA you really don't need a spare, however, here in
Australia there are unpaved roads in parts of Queensland and the Outback. I was working on Double Trouble at the Coop back in 2008
and found a couple on used axles in JimB's used spare pile and he sold them to me so now both GMC's have them.

The reason I mentioned this is to keep an eye out for a pair on eBay. Unfortunately I do not have the part number, manufacturer, or
any details available or I'd share them.

Regards,
Rob M.
Sydney, Australia
AUS '75 Avion - The Blue Streak TZE365V100428
USA '75 Avion - Double Trouble TZE365V100426



-----Original Message-----
From: Nick Chapekis

Try this: Dorman universal fit (part # 614-003)

I got a new boot for one side, then a rebuilt CV joint and boot for the other side, both from Jim Kanomata a few years back. The CV
joint was fine, however neither of the boots lasted very long. Both were replaced by Dorman split boots, which are still good,
although as Matt mentioned, our coach doesn't get high usage (proabably average usage for non-retirees though).
--
Nick

_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist



Regards, Rob M. (USAussie) The Pedantic Mechanic Sydney, Australia '75 Avion - AUS - The Blue Streak TZE365V100428 '75 Avion - USA - Double Trouble TZE365V100426
Re: [GMCnet] Split Boot Installation [message #269623 is a reply to message #269616] Tue, 13 January 2015 17:35 Go to previous messageGo to next message
Emery Stora is currently offline  Emery Stora   United States
Messages: 959
Registered: January 2011
Karma: 4
Senior Member
Hi Rob

The blue boots were called a SuperBoot" from NAPA. It was a blue polyurethane boot. Napa part number: 2456SB. They are no longer available at NAPA.

I did a quick internet search and found this:

http://www.carpartkings.com/dorman-cv-joint-boot-614-434.html

They might fit the GMC motorhome but one would have to check the dimensions first. The right one should cross to a 1976 Olds Toronado.

Emery Stora
77 Kingsley
Frederick, CO

> On Jan 13, 2015, at 3:37 PM, Robert Mueller wrote:
>
> G'day,
>
> This is for Newbies.
>
> YEARS ago there were boots made of silicone available for the GMC; they were colored blue and were called "blue boots" (how's that
> for demonstrating an acute grasp on the obvious) unfortunately they are no longer manufactured as they are virtually indestructible!
>
>
> I had the good fortune of obtaining a pair from a gentleman here on the GMCnet and one extra from a second gentleman here. The pair
> was installed on The Blue Streak and the spare is held here as well. In the USA you really don't need a spare, however, here in
> Australia there are unpaved roads in parts of Queensland and the Outback. I was working on Double Trouble at the Coop back in 2008
> and found a couple on used axles in JimB's used spare pile and he sold them to me so now both GMC's have them.
>
> The reason I mentioned this is to keep an eye out for a pair on eBay. Unfortunately I do not have the part number, manufacturer, or
> any details available or I'd share them.
>
> Regards,
> Rob M.
> Sydney, Australia
> AUS '75 Avion - The Blue Streak TZE365V100428
> USA '75 Avion - Double Trouble TZE365V100426
>
>
>
> -----Original Message-----
> From: Nick Chapekis
>
> Try this: Dorman universal fit (part # 614-003)
>
> I got a new boot for one side, then a rebuilt CV joint and boot for the other side, both from Jim Kanomata a few years back. The CV
> joint was fine, however neither of the boots lasted very long. Both were replaced by Dorman split boots, which are still good,
> although as Matt mentioned, our coach doesn't get high usage (probably average usage for non-retirees though).
> --
> Nick
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

Re: [GMCnet] Split Boot Installation [message #269624 is a reply to message #269616] Tue, 13 January 2015 17:37 Go to previous messageGo to next message
Emery Stora is currently offline  Emery Stora   United States
Messages: 959
Registered: January 2011
Karma: 4
Senior Member
Rob
Forgot to mention in my previous message that they we re not silicone. They were polyurethane.

Emery Stora

> On Jan 13, 2015, at 3:37 PM, Robert Mueller wrote:
>
> G'day,
>
> This is for Newbies.
>
> YEARS ago there were boots made of silicone available for the GMC; they were colored blue and were called "blue boots" (how's that
> for demonstrating an acute grasp on the obvious) unfortunately they are no longer manufactured as they are virtually indestructible!
>
>
> I had the good fortune of obtaining a pair from a gentleman here on the GMCnet and one extra from a second gentleman here. The pair
> was installed on The Blue Streak and the spare is held here as well. In the USA you really don't need a spare, however, here in
> Australia there are unpaved roads in parts of Queensland and the Outback. I was working on Double Trouble at the Coop back in 2008
> and found a couple on used axles in JimB's used spare pile and he sold them to me so now both GMC's have them.
>
> The reason I mentioned this is to keep an eye out for a pair on eBay. Unfortunately I do not have the part number, manufacturer, or
> any details available or I'd share them.
>
> Regards,
> Rob M.
> Sydney, Australia
> AUS '75 Avion - The Blue Streak TZE365V100428
> USA '75 Avion - Double Trouble TZE365V100426
>
>
>
> -----Original Message-----
> From: Nick Chapekis
>
> Try this: Dorman universal fit (part # 614-003)
>
> I got a new boot for one side, then a rebuilt CV joint and boot for the other side, both from Jim Kanomata a few years back. The CV
> joint was fine, however neither of the boots lasted very long. Both were replaced by Dorman split boots, which are still good,
> although as Matt mentioned, our coach doesn't get high usage (proabably average usage for non-retirees though).
> --
> Nick
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

Re: Split Boot Installation [message #269645 is a reply to message #269563] Wed, 14 January 2015 09:23 Go to previous messageGo to next message
rscortezzo is currently offline  rscortezzo   United States
Messages: 49
Registered: January 2007
Location: Green Valley Arizona/ Flo...
Karma: 0
Member
Found on Amazon for about eighteen dollars, free shipping with Amazon prime, some good reviews.

Rich Cortezzo
Green Valley AZ
1978 Eleganza II F389018
Re: Split Boot Installation [message #269646 is a reply to message #269645] Wed, 14 January 2015 09:32 Go to previous messageGo to next message
Loffen is currently offline  Loffen   Norway
Messages: 1087
Registered: August 2013
Location: Norway
Karma: 1
Senior Member
From my experience split boots are crap, spend some more time and do it right.

1973 23' # 1848 Sky Blue Glacier called Baby Blue and a 1973 26'-3 # 1460 Parrot green Seqouia Known as the Big Green, And sold my 1973 26'-2 # 581 White Canyon lands under the name Dobbelt trøbbel in Norway
Re: Split Boot Installation [message #269649 is a reply to message #269646] Wed, 14 January 2015 10:28 Go to previous messageGo to next message
tphipps is currently offline  tphipps   United States
Messages: 3005
Registered: August 2004
Location: Spanish Fort, AL
Karma: 9
Senior Member
To add to the part number confusion, going to Dorman's web site, and checking both #03608 and #03609, Dorman says neither will fit a 75 Olds Toronado.
However, I ordered #03609, based on a string of a few years back, and it fit perfectly.
On this list, there are no reported failures with the Dorman Split Boots installed on the GMC motorhome. Probably a lower stress environment. I'll report back after the touring season.
At the moment, I am pleased with it. The big end fit perfectly, the small end fit perfectly, and the length of the body did not result in any stretching of the boot.
Tom, MS II


2012 Phoenix Cruiser model 2552 KA4CSG
Re: Split Boot Installation [message #269650 is a reply to message #269649] Wed, 14 January 2015 10:35 Go to previous messageGo to next message
GMC Cruse is currently offline  GMC Cruse   United States
Messages: 606
Registered: June 2009
Location: SE Michigan
Karma: 3
Senior Member
tphipps wrote on Wed, 14 January 2015 11:28
To add to the part number confusion, going to Dorman's web site, and checking both #03608 and #03609, Dorman says neither will fit a 75 Olds Toronado.
However, I ordered #03609, based on a string of a few years back, and it fit perfectly.
On this list, there are no reported failures with the Dorman Split Boots installed on the GMC motorhome. Probably a lower stress environment. I'll report back after the touring season.
At the moment, I am pleased with it. The big end fit perfectly, the small end fit perfectly, and the length of the body did not result in any stretching of the boot.
Tom, MS II


A spare one came with my GMC and it is also #03609


Mike K. '75 PB Southeast Michigan
Re: Split Boot Installation [message #269654 is a reply to message #269646] Wed, 14 January 2015 11:43 Go to previous messageGo to next message
midlf is currently offline  midlf   United States
Messages: 2212
Registered: July 2007
Location: SE Wisc. (Palmyra)
Karma: 1
Senior Member
Loffen wrote on Wed, 14 January 2015 09:32
From my experience split boots are crap, spend some more time and do it right.



I haven't used a split boot but I tend to agree with Loffen that shortcuts are, all too often, future trouble. HOWEVER I plan to get one of 03609 split boots as an emergency spare to use until I can get it fixed right.


Steve Southworth
1974 Glacier TZE064V100150 (for workin on)
1975 Transmode TZE365V100394 (parts & spares)
Palmyra WI
Re: [GMCnet] Split Boot Installation [message #269655 is a reply to message #269649] Wed, 14 January 2015 11:44 Go to previous messageGo to next message
Mr ERFisher is currently offline  Mr ERFisher   United States
Messages: 7117
Registered: August 2005
Karma: 2
Senior Member
On Wednesday, January 14, 2015, Thomas Phipps wrote:

> To add to the part number confusion, going to Dorman's web site, and
> checking both #03608 and #03609, Dorman says neither will fit a 75 Olds
> Toronado.
> However, I ordered #03609, based on a string of a few years back, and it
> fit perfectly.
> On this list, there are no reported failures with the Dorman Split Boots
> installed on the GMC motorhome. Probably a lower stress environment. I'll


I had 2 failures with the split boot
Finally replaced with a new boot

Erf

> report back after the touring season.
> At the moment, I am pleased with it. The big end fit perfectly, the small
> end fit perfectly, and the length of the body did not result in any
> stretching of the boot.
> Tom, MS II
> --
> 1975 GMC Avion
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>


--
Gene Fisher -- 74-23,77PB/ore/ca
“Give a man a fish; you have fed him for today --- give him a URL and
-------
http://gmcmotorhome.info/
Alternator Protection Cable
http://gmcmotorhome.info/APC.html
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Re: Split Boot Installation [message #269672 is a reply to message #269654] Wed, 14 January 2015 15:03 Go to previous messageGo to previous message
Loffen is currently offline  Loffen   Norway
Messages: 1087
Registered: August 2013
Location: Norway
Karma: 1
Senior Member
midlf wrote on Wed, 14 January 2015 18:43
Loffen wrote on Wed, 14 January 2015 09:32
From my experience split boots are crap, spend some more time and do it right.



I haven't used a split boot but I tend to agree with Loffen that shortcuts are, all too often, future trouble. HOWEVER I plan to get one of 03609 split boots as an emergency spare to use until I can get it fixed right.


For an emergency it is all right, so is also a plastic bag, fold it once, wrap it around the CV joint a couple of times and hold it in place with some tape Wink


1973 23' # 1848 Sky Blue Glacier called Baby Blue and a 1973 26'-3 # 1460 Parrot green Seqouia Known as the Big Green, And sold my 1973 26'-2 # 581 White Canyon lands under the name Dobbelt trøbbel in Norway
Previous Topic: [GMCnet] The area under the brake and gas pedal
Next Topic: [GMCnet] no mail
Goto Forum:
  


Current Time: Sat Nov 16 14:12:37 CST 2024

Total time taken to generate the page: 0.02793 seconds