Home » Public Forums » GMCnet » [GMCnet] Wallace Bearing Tru-Track
|
Re: [GMCnet] Wallace Bearing Tru-Track [message #267206 is a reply to message #267191] |
Fri, 05 December 2014 18:46 |
|
ljdavick
Messages: 3548 Registered: March 2007 Location: Fremont, CA
Karma: -3
|
Senior Member |
|
|
I don't know about the Wallace tru-track specifically, but in general I feel that these kind of things (tru-trackers in general) are a fantastic addition to the coach. Particularly for the leading bogie, but also for the rear. The bogies flex a surprising amount when you are turning the coach, and other forces, such as pot-holes, will cause them to flex while going down the road.
There was some discussion about straight vs curved channel tru-tracks, but I think they all do some good. I suppose the curved ones are prefered, but so long as the bearing is within the channel then I'd be okay with it.
If my beloved PO hadn't installed them I would.
Larry Davick
Fremont, California
A Mystery Machine
'76 (ish) Palm Beach
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Larry Davick
A Mystery Machine
1976(ish) Palm Beach
Fremont, Ca
Howell EFI + EBL + Electronic Dizzy
|
|
|
Re: [GMCnet] Wallace Bearing Tru-Track [message #267224 is a reply to message #267206] |
Sat, 06 December 2014 06:49 |
tphipps
Messages: 3005 Registered: August 2004 Location: Spanish Fort, AL
Karma: 9
|
Senior Member |
|
|
Install them. At least do the mid-wheel position, as it will keep that boggie pointing forward without deflection. There has been discussion about doing only the mids, as the rear wheels are in a trailing position and stay in track. Some have split the full set and two GMCers paired on the mid wheels.
JWIWD.
Tom, MS II
2012 Phoenix Cruiser model 2552
KA4CSG
|
|
|
|
Re: [GMCnet] Wallace Bearing Tru-Track [message #267285 is a reply to message #267206] |
Sun, 07 December 2014 11:52 |
Albert Friesen
Messages: 9 Registered: November 2014
Karma: 0
|
Junior Member |
|
|
My thinking on the Tru-Track system is that grit word play heck with the
slide part and bearing.
I also have a set of rear stabilizer bars. Would the bars put too much
lateral stress on the suspension members?
Any ideas would be much appreciated.
I find as a new member that I am getting a lot of good info on this
motorhome.
I have 15+ year old Michelin tires while show very little checking and only
between the side tread area. How far would anyone drive on these old tires.
This MH has not seen salt nor parking on grass so is in very good
condition, rust wise. Just a little dated interior.
I am thinking of removing the double bunk and putting a chair of some sort.
Loose some storage but gain floor space.
In putting a laminate floor does one just cut out the carpet in the walking
area? Lifting all the cupboards and dinette is a big job.
Well that's enough cvestions for now that is. Al
On Fri, Dec 5, 2014 at 7:46 PM, Larry Davick wrote:
> I don't know about the Wallace tru-track specifically, but in general I
> feel that these kind of things (tru-trackers in general) are a fantastic
> addition to the coach. Particularly for the leading bogie, but also for
> the rear. The bogies flex a surprising amount when you are turning the
> coach, and other forces, such as pot-holes, will cause them to flex while
> going down the road.
>
> There was some discussion about straight vs curved channel tru-tracks, but
> I think they all do some good. I suppose the curved ones are prefered, but
> so long as the bearing is within the channel then I'd be okay with it.
>
> If my beloved PO hadn't installed them I would.
>
> Larry Davick
> Fremont, California
> A Mystery Machine
> '76 (ish) Palm Beach
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
Re: [GMCnet] Wallace Bearing Tru-Track [message #267286 is a reply to message #267285] |
Sun, 07 December 2014 12:04 |
tphipps
Messages: 3005 Registered: August 2004 Location: Spanish Fort, AL
Karma: 9
|
Senior Member |
|
|
15 year tires. I would drive to the nearest tire dealer that had the tire that I wanted and at the price I was willing to pay, and replace them. Even for Michelins, 15 years is aged too much. Michelin claims 10 years as an optimal life. Others say 7 years.
JWIWD.
Tom, MS II
2012 Phoenix Cruiser model 2552
KA4CSG
|
|
|
Re: [GMCnet] Wallace Bearing Tru-Track [message #267289 is a reply to message #267286] |
Sun, 07 December 2014 14:51 |
powerjon
Messages: 2446 Registered: January 2004
Karma: 5
|
Senior Member |
|
|
As for 15 year old tires I personally would even drive them anywhere. Take them off and then take them to the dealer. The cost of repairing tire damage is way more that a set of tires. There are people here that know. You do what you want.
JR Wright
78 Buskirk Stretch
75 Avion
Michigan
> On Dec 7, 2014, at 1:04 PM, Thomas Phipps wrote:
>
> 15 year tires. I would drive to the nearest tire dealer that had the tire that I wanted and at the price I was willing to pay, and replace them.
> Even for Michelins, 15 years is aged too much. Michelin claims 10 years as an optimal life. Others say 7 years.
> JWIWD.
> Tom, MS II
> --
> 1975 GMC Avion
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
J.R. Wright
GMC GreatLaker
GMC Eastern States
GMCMI
78 30' Buskirk Stretch
75 Avion Under Reconstruction
Michigan
|
|
|
Re: [GMCnet] Wallace Bearing Tru-Track [message #267290 is a reply to message #267289] |
Sun, 07 December 2014 15:00 |
Albert Friesen
Messages: 9 Registered: November 2014
Karma: 0
|
Junior Member |
|
|
I had a blow tire on a trailer back in 1975. I did a job on the plenum tin
wheel well. They were almost new Firestone's. Got a new one under
warranty. Al
On Sun, Dec 7, 2014 at 3:51 PM, John Wright wrote:
> As for 15 year old tires I personally would even drive them anywhere.
> Take them off and then take them to the dealer. The cost of repairing tire
> damage is way more that a set of tires. There are people here that know.
> You do what you want.
>
> JR Wright
> 78 Buskirk Stretch
> 75 Avion
> Michigan
>
>> On Dec 7, 2014, at 1:04 PM, Thomas Phipps wrote:
>>
>> 15 year tires. I would drive to the nearest tire dealer that had the
> tire that I wanted and at the price I was willing to pay, and replace them.
>> Even for Michelins, 15 years is aged too much. Michelin claims 10 years
> as an optimal life. Others say 7 years.
>> JWIWD.
>> Tom, MS II
>> --
>> 1975 GMC Avion
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
Re: [GMCnet] Wallace Bearing Tru-Track [message #267292 is a reply to message #267285] |
Sun, 07 December 2014 15:30 |
|
USAussie
Messages: 15912 Registered: July 2007 Location: Sydney, Australia
Karma: 6
|
Senior Member |
|
|
G'day,
I have a Tru Trak system made by Tom Hampton of Grandview Motor Homes and there is sufficient clearance between the roller and track
to cope with grit.
I don't think stabilizer bars will put any stress on the suspension, however, they WILL effect the ability to level the rear end at
campsites because it hooks both sides together.
To be 100% safe I would remove the wheels and tires and bring them to a tire store to have new tires fitted.
The carpet in the Avion didn't go under the furniture.
Regards,
Rob M.
Sydney, Australia
AUS '75 Avion - The Blue Streak TZE365V100428
USA '75 Avion - Double Trouble TZE365V100426
-----Original Message-----
From: Albert Friesen
My thinking on the Tru-Track system is that grit word play heck with the
slide part and bearing.
I also have a set of rear stabilizer bars. Would the bars put too much
lateral stress on the suspension members?
Any ideas would be much appreciated.
I find as a new member that I am getting a lot of good info on this
motorhome.
I have 15+ year old Michelin tires while show very little checking and only
between the side tread area. How far would anyone drive on these old tires.
This MH has not seen salt nor parking on grass so is in very good
condition, rust wise. Just a little dated interior.
I am thinking of removing the double bunk and putting a chair of some sort.
Loose some storage but gain floor space.
In putting a laminate floor does one just cut out the carpet in the walking
area? Lifting all the cupboards and dinette is a big job.
Well that's enough cvestions for now that is. Al
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Regards,
Rob M. (USAussie)
The Pedantic Mechanic
Sydney, Australia
'75 Avion - AUS - The Blue Streak TZE365V100428
'75 Avion - USA - Double Trouble TZE365V100426
|
|
|
Re: [GMCnet] Wallace Bearing Tru-Track [message #267294 is a reply to message #267292] |
Sun, 07 December 2014 16:02 |
Albert Friesen
Messages: 9 Registered: November 2014
Karma: 0
|
Junior Member |
|
|
Thanks all for the info. I will be installing the front Tru-Track and see
if they do the trick. I don't think I will remove the furniture to put in
new carpet of Laminate flooring. The tires will travel 1 mile to the tire
shop. I have a price for Firestones TransForce HT at 203.00 plus tax per
tire. Are they the correct tire? Al
On Sun, Dec 7, 2014 at 4:30 PM, Robert Mueller
wrote:
> G'day,
>
> I have a Tru Trak system made by Tom Hampton of Grandview Motor Homes and
> there is sufficient clearance between the roller and track
> to cope with grit.
>
> I don't think stabilizer bars will put any stress on the suspension,
> however, they WILL effect the ability to level the rear end at
> campsites because it hooks both sides together.
>
> To be 100% safe I would remove the wheels and tires and bring them to a
> tire store to have new tires fitted.
>
> The carpet in the Avion didn't go under the furniture.
>
> Regards,
> Rob M.
> Sydney, Australia
> AUS '75 Avion - The Blue Streak TZE365V100428
> USA '75 Avion - Double Trouble TZE365V100426
>
> -----Original Message-----
> From: Albert Friesen
>
> My thinking on the Tru-Track system is that grit word play heck with the
> slide part and bearing.
> I also have a set of rear stabilizer bars. Would the bars put too much
> lateral stress on the suspension members?
> Any ideas would be much appreciated.
> I find as a new member that I am getting a lot of good info on this
> motorhome.
> I have 15+ year old Michelin tires while show very little checking and only
> between the side tread area. How far would anyone drive on these old tires.
> This MH has not seen salt nor parking on grass so is in very good
> condition, rust wise. Just a little dated interior.
> I am thinking of removing the double bunk and putting a chair of some sort.
> Loose some storage but gain floor space.
> In putting a laminate floor does one just cut out the carpet in the walking
> area? Lifting all the cupboards and dinette is a big job.
> Well that's enough cvestions for now that is. Al
>
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
Re: [GMCnet] Wallace Bearing Tru-Track [message #267304 is a reply to message #267285] |
Sun, 07 December 2014 17:43 |
Ken Henderson
Messages: 8726 Registered: March 2004 Location: Americus, GA
Karma: 9
|
Senior Member |
|
|
Albert,
Tru-Trac, on the middle wheels, is probably the single best improvement
I've done to my suspension -- and I've done them ALL. I would not give
them up for any reason. I did not want them on the rear wheels. In the
first place, I don't think those trailing suspension arms can go anywhere
without the rest of the wheels having already been there. In the second
place, I think some compliance in the rear suspension during turns is
desirable -- more than the tires' sidewalls can safely offer.
All of the cam followers I've seen used for Tru-Trac's have sealed
bearings; grit should not be a problem -- I'm not even very conscientious
about greasing them.
I had a coach with rear stabilizer bars and never will again. Not because
of any stress but because they made it virtually impossible to level the
coach with the air bags -- when one side goes up or down, so does the
other. I've got two of them for sale if someone wants them -- no shipping
though. :-)
I'd put those wheels and 15 year old tires in the back of my truck,
carefully, and take them to the tire store. Would NOT drive the coach that
far (about a mile).
IMHO it would be foolish to remove the cabinets just to get the carpet
out. Even when I replaced all the cabinets, I did not put the new ones on
top of the carpet -- that's purely a production line time saver.
HTH,
Ken H.
Americus, GA
'76 X-Birchaven w/Cad500/Howell EFI & EBL,
Manny Brakes & 1-Ton, etc., etc.
www.gmcwipersetc.com
On Sun, Dec 7, 2014 at 12:52 PM, Albert Friesen wrote:
> My thinking on the Tru-Track system is that grit word play heck with the
> slide part and bearing.
> I also have a set of rear stabilizer bars. Would the bars put too much
> lateral stress on the suspension members?
> Any ideas would be much appreciated.
> I find as a new member that I am getting a lot of good info on this
> motorhome.
> I have 15+ year old Michelin tires while show very little checking and only
> between the side tread area. How far would anyone drive on these old tires.
> This MH has not seen salt nor parking on grass so is in very good
> condition, rust wise. Just a little dated interior.
> I am thinking of removing the double bunk and putting a chair of some sort.
> Loose some storage but gain floor space.
> In putting a laminate floor does one just cut out the carpet in the walking
> area? Lifting all the cupboards and dinette is a big job.
> Well that's enough cvestions for now that is. Al
> ...
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Ken Henderson
Americus, GA
www.gmcwipersetc.com
Large Wiring Diagrams
76 X-Birchaven
76 X-Palm Beach
|
|
|
Re: [GMCnet] Wallace Bearing Tru-Track [message #267307 is a reply to message #267301] |
Sun, 07 December 2014 18:37 |
Albert Friesen
Messages: 9 Registered: November 2014
Karma: 0
|
Junior Member |
|
|
I might need some help on putting a signature on all my mail. As to the
rims, they are 16.5 with Michelin's. 875 75R/ 16.5. They towed OK from
the seller to the service garage and then home, total about 65 miles. They
have been in a garage since about 1990. Al
On Sun, Dec 7, 2014 at 6:01 PM, Robert Mueller
wrote:
> Al,
>
> Please advise if your wheels on your 75 GMC Eleganza II are 16 inch or
> 16.5 inch.
>
> Please create a signature like this:
>
> Al Friesen
> '75 Eleganza II
> City, State
>
> This will help us help you.
>
> Regards,
> Rob M.
> Sydney, Australia
> AUS '75 Avion - The Blue Streak TZE365V100428
> USA '75 Avion - Double Trouble TZE365V100426
>
>
> -----Original Message-----
> From: Albert Friesen
>
> Thanks all for the info. I will be installing the front Tru-Track and see
> if they do the trick. I don't think I will remove the furniture to put in
> new carpet of Laminate flooring. The tires will travel 1 mile to the tire
> shop. I have a price for Firestones TransForce HT at 203.00 plus tax per
> tire. Are they the correct tire? Al
>
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
Re: [GMCnet] Wallace Bearing Tru-Track [message #267309 is a reply to message #267294] |
Sun, 07 December 2014 18:44 |
Joe Weir
Messages: 769 Registered: February 2013 Location: Columbia, SC
Karma: 7
|
Senior Member |
|
|
Albert Friesen wrote on Sun, 07 December 2014 16:02Thanks all for the info. I will be installing the front Tru-Track and see
if they do the trick. I don't think I will remove the furniture to put in
new carpet of Laminate flooring. The tires will travel 1 mile to the tire
shop. I have a price for Firestones TransForce HT at 203.00 plus tax per
tire. Are they the correct tire? Al
I currently have the transforces - its the only one Firestone makes in the 16.5 truck size. Mine are two years old with 50 miles on them. I'd make you a heck of a deal on a set already mounted if you were close enough. I have a set of Alcoas waiting.
I'd be interested if you decide to sell the other half of that set of true tracks...
76 Birchaven - "Wicked Mistress" - New engine, trans, alum radiator, brakes, Sully airbags, fuel lines, seats, adult beverage center... those Coachmen guys were really thinking about us second hand owners by including that beverage center...
Columbia, SC.
|
|
|
|
Re: [GMCnet] Wallace Bearing Tru-Track [message #267328 is a reply to message #267307] |
Mon, 08 December 2014 11:12 |
|
Matt Colie
Messages: 8547 Registered: March 2007 Location: S.E. Michigan
Karma: 7
|
Senior Member |
|
|
Albert Friesen wrote on Sun, 07 December 2014 19:37I might need some help on putting a signature on all my mail. As to the rims, they are 16.5 with Michelin's. 875 75R/ 16.5. They towed OK from the seller to the service garage and then home, total about 65 miles. They have been in a garage since about 1990. Al
Al,
Firestone transforce are your only choice for a US made tire. I am told that there are some Chinese products, but none showed up in my last search. I was told that there are still some Coopers around but my local Cooper dealer declined to provide them.
Matt
Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL, GMCES
Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum Brakes with Applied Control Arms
SE Michigan - Near DTW - Twixt A2 and Detroit
|
|
|
Goto Forum:
Current Time: Tue Nov 19 00:02:14 CST 2024
Total time taken to generate the page: 0.01245 seconds
|