GMCforum: GMCnet » Gettin' 'er Done

Home » Public Forums » GMCnet » Gettin' 'er Done (Rolls Royce and the GMC)

Show: Today's Messages :: Polls :: Message Navigator

Gettin' 'er Done [message #254000]

Tue, 01 July 2014 14:09

George Beckman

Messages: 1085
Registered: October 2008
Location: Colfax, CA

Karma:

Senior Member

I like to get things done. That doesn't mean I do them, I just like to get things done.

Right before the trip from California to the Branson Rally, last fall, the speedometer quit. This made me grumpy because I have fuel injection and without the speedometer working I don't have Lean Cruise; I don't have my MPG reading. Upon examination, I began to realize that the speedometer gear, where the speedometer cable attaches, was wallowed out inside. The second night out I cut up a soda can and made some shims to shove in with the cable tip. The speedometer worked and I was a happy man.

Since that time I jammed more soda can slivers in the back of the speedometer gear. Manny to the rescue. I had a good one on my work bench, along with other unfinished projects. I like to keep my unfinished project handy.

Today, because I like to get things done, I put the new part in... after months of procrastination. I suppose because I finally got the new fan clutch in a couple of weeks ago I was inflamed with checking things off my list.

As I lay under the coach, admiring my work, I could see grease zerks. If I twisted my head I also could see my grease gun under my work bench. It is warm today and the cement was cool in the barn so I rested a bit, deciding if I wanted to do one of my unfavorite jobs. I decided to grease the motor home. After all, it was already on jack stands.

As I was twisting and turning, grunting and straining, I remembered an article in the paper about a fellow with a Rolls Royce in the next town over. The article said it had a pedal on the floorboards you could push to send grease to all fittings.

If I had one of those pedals I could get things done. Maybe I could mount one by my chair, in the house.

'74 Eleganza, SE, Howell + EBL
Best Wishes,
George

Report message to a moderator

[Message index]

		Gettin' 'er Done By: George Beckman on Tue, 01 July 2014 14:09
		Re: Gettin' 'er Done By: Keith V on Tue, 01 July 2014 15:06
		Re: Gettin' 'er Done By: djester on Tue, 01 July 2014 15:13
		Re: Gettin' 'er Done By: cbryan on Tue, 01 July 2014 17:39
		Re: Gettin' 'er Done By: kerry pinkerton on Tue, 01 July 2014 18:39
		Re: Gettin' 'er Done By: SteveW on Tue, 01 July 2014 18:50
		Re: [GMCnet] Gettin' 'er Done By: Ken Henderson on Tue, 01 July 2014 19:18
		Re: Gettin' 'er Done By: glenn2726 on Wed, 02 July 2014 01:21
		Re: Gettin' 'er Done By: Ken Burton on Wed, 02 July 2014 04:02
		Re: Gettin' 'er Done By: cbryan on Wed, 02 July 2014 09:44
		Re: Gettin' 'er Done By: midlf on Wed, 02 July 2014 10:45
		Re: Gettin' 'er Done By: Neil on Wed, 02 July 2014 11:13
		Re: [GMCnet] Gettin' 'er Done By: USAussie on Wed, 02 July 2014 11:40
		Re: [GMCnet] Gettin' 'er Done By: Neil on Wed, 02 July 2014 13:03
		Re: [GMCnet] Gettin' 'er Done By: USAussie on Wed, 02 July 2014 23:53
		Re: [GMCnet] Gettin' 'er Done By: USAussie on Wed, 02 July 2014 11:00
		Re: [GMCnet] Gettin' 'er Done By: George Beckman on Thu, 03 July 2014 01:21
		Re: [GMCnet] Gettin' 'er Done By: midlf on Thu, 03 July 2014 07:08
		Re: Gettin' 'er Done By: SteveW on Wed, 02 July 2014 10:09
		Re: Gettin' 'er Done By: cbryan on Wed, 02 July 2014 16:52

Previous Topic:	OLP status
Next Topic:	OLP & No-IP working again

Goto Forum:

-=] Back to Top [=-

Current Time: Tue Nov 19 08:04:13 CST 2024

Total time taken to generate the page: 0.00931 seconds