|
|
| Re: Dims for countertop Palm Beach [message #251519 is a reply to message #251517] |
Wed, 04 June 2014 17:00   |
Carl S.
Messages: 4186
Registered: January 2009
Location: Tucson, AZ.
Karma: 13
|
Senior Member |
|
|
JJUNKSELL wrote on Wed, 04 June 2014 14:18Need all dims for countertop in a Palm Beach. Thanks Dave
Dave,
I can measure my counter top, length and width, when I get home if that would help. My counter top had been replaced before I bought the coach and had a three burner stove top installed, so none of the cut-outs are standard. It DID have the original sink though.
I have since replaced the laminate counter top with Corian, an undermount sink, and a two burner sink.
http://www.gmcmhphotos.com/photos/counter-top-etc/p40880-all-done.html
Here's what the old one looked like:
http://www.gmcmhphotos.com/photos/bruce-and-elizabeth-tara-75-pb-from-start-to-almost-finished/p4581.html
Carl Stouffer
'75 ex Palm Beach
Tucson, AZ.
Chuck Aulgur Reaction Arm Disc Brakes, Quadrabags, 3.70 LSD final drive, Lenzi knuckles/hubs, Dodge Truck 16" X 8" front wheels, Rear American Eagles, Solar battery charging. GMCSJ and GMCMI member
|
|
|
|
| Re: Dims for countertop Palm Beach [message #251520 is a reply to message #251519] |
Wed, 04 June 2014 17:28 |
JJUNKSELL
Messages: 58
Registered: July 2013
Location: MERIDEN CT
Karma: 0
|
Member |
|
|
Thanks Carl, Im looking for the original dims at the moment. I may change my mind in the future and do someting like you did.IM sorta tryin to stay close to original. Thanks again, Dave
Dave, 76 PB moneypit.Center of CT.
|
|
|
|
| Re: Dims for countertop Palm Beach [message #251522 is a reply to message #251520] |
Wed, 04 June 2014 19:07 |
Carl S.
Messages: 4186
Registered: January 2009
Location: Tucson, AZ.
Karma: 13
|
Senior Member |
|
|
I'm guessing you still have the cabinet in place. That is about the only set of dimensions I could provide. I think the original counter top had a very shallow backsplash, a few inches from the wall, with a flat piece of counter behind it. The sink will be as far to the right and the front as you can get it a without interfering with the cabinet face frame below it. The stove cutout will be dictated by the location of the stove underneath as well. It shouldn't be too hard to lay out.
Carl Stouffer
'75 ex Palm Beach
Tucson, AZ.
Chuck Aulgur Reaction Arm Disc Brakes, Quadrabags, 3.70 LSD final drive, Lenzi knuckles/hubs, Dodge Truck 16" X 8" front wheels, Rear American Eagles, Solar battery charging. GMCSJ and GMCMI member
|
|
|
|
| Re: Dims for countertop Palm Beach [message #251527 is a reply to message #251520] |
Wed, 04 June 2014 19:42 |
Otterwan
Messages: 946
Registered: July 2013
Location: Lynnwood (north of Seattl...
Karma: 0
|
Senior Member |
|
|
JJUNKSELL wrote on Wed, 04 June 2014 15:28Thanks Carl, Im looking for the original dims at the moment. I may change my mind in the future and do someting like you did.IM sorta tryin to stay close to original. Thanks again, Dave
I have a 1978 palm beach that I believe is stock. What dimensions do you need?
1977 Birchaven, Lynnwood WA - "We may not be able to stop all evil in the world, but I know that how we treat one another is entirely up to us."
|
|
|
|
| Re: Dims for countertop Palm Beach [message #251530 is a reply to message #251527] |
Wed, 04 June 2014 20:06 |
JJUNKSELL
Messages: 58
Registered: July 2013
Location: MERIDEN CT
Karma: 0
|
Member |
|
|
Im looking for the length, width, thickness,height of backsplash,location of cutouts for stove and sink, and any dims I might not have thought of. Thanks, Dave
Dave, 76 PB moneypit.Center of CT.
|
|
|
|
| Re: Dims for countertop Palm Beach [message #251531 is a reply to message #251530] |
Wed, 04 June 2014 20:16 |
Otterwan
Messages: 946
Registered: July 2013
Location: Lynnwood (north of Seattl...
Karma: 0
|
Senior Member |
|
|
I'll take a look tomorrow. Too bad you aren't closer, you could just take the whole counter top!
1977 Birchaven, Lynnwood WA - "We may not be able to stop all evil in the world, but I know that how we treat one another is entirely up to us."
|
|
|
|
GMCforum
Search
Help
Register
Login
Home
