GMCforum: GMCnet » updating Olga

Home » Public Forums » GMCnet » updating Olga

Show: Today's Messages :: Polls :: Message Navigator

updating Olga [message #242603]

Fri, 07 March 2014 07:52

appie

Messages: 902
Registered: April 2013
Location: denmark

Karma:

Senior Member

A while ago I discussed wether nptf sender would fit the npt thread in the engine
Well they do- no problem just have to be careful not to apply to much force

Today i tested my oilpressure with a manual gauge- pretty much the same even though the manual is reacting a bit faster
45 stone cold- falling to 15 as the thermostat opens Nicely following the rev in P 30 at 2000
driving falling to 7 and following revs but at a lower rate 15-20 at 2000

this is with 10-30 oil

vacuum stays nicely at 22Hg at idle very stable

Appie eleganza 76 "Olga" now sadly sold 6 wheel discbrake Quadrabags Springfield stage 2 462 olds Manny tranny ( pictures at http://www.gmcmhphotos.com/photos/g6489-olga.html Fulltiming in Europe july 2014 til july 2016 Denmark

Report message to a moderator

[Message index]

		updating Olga By: appie on Fri, 07 March 2014 07:52
		Re: updating Olga By: Loffen on Fri, 07 March 2014 07:57
		Re: updating Olga By: appie on Fri, 07 March 2014 08:20
		Re: updating Olga By: Ken Burton on Fri, 07 March 2014 09:15
		Re: updating Olga By: Loffen on Fri, 07 March 2014 09:22
		Re: updating Olga By: Ken Burton on Fri, 07 March 2014 09:33
		Re: updating Olga By: Loffen on Fri, 07 March 2014 09:37
		Re: updating Olga By: appie on Fri, 07 March 2014 09:54
		Re: updating Olga By: Loffen on Fri, 07 March 2014 10:12
		Re: updating Olga By: appie on Fri, 07 March 2014 10:43
		Re: updating Olga By: Loffen on Fri, 07 March 2014 11:01
		Re: [GMCnet] updating Olga By: James Hupy on Fri, 07 March 2014 11:00
		Re: [GMCnet] updating Olga By: appie on Fri, 07 March 2014 11:21
		Re: [GMCnet] updating Olga By: Loffen on Fri, 07 March 2014 11:32
		Re: [GMCnet] updating Olga By: James Hupy on Fri, 07 March 2014 11:36
		Re: [GMCnet] updating Olga By: appie on Fri, 07 March 2014 12:42
		Re: [GMCnet] updating Olga By: Bullitthead on Sun, 16 March 2014 01:00
		Re: [GMCnet] updating Olga By: appie on Sun, 16 March 2014 01:59
		Re: [GMCnet] updating Olga By: Ken Henderson on Fri, 07 March 2014 11:40
		Re: [GMCnet] updating Olga By: Loffen on Fri, 07 March 2014 11:48
		Re: [GMCnet] updating Olga By: jhbridges on Fri, 07 March 2014 12:09
		Re: [GMCnet] updating Olga By: Loffen on Fri, 07 March 2014 12:17
		Re: [GMCnet] updating Olga By: Ken Henderson on Fri, 07 March 2014 12:21
		Re: [GMCnet] updating Olga By: Olly Schmidt on Fri, 07 March 2014 13:49
		Re: [GMCnet] updating Olga By: Kingsley Coach on Fri, 07 March 2014 17:32
		Re: [GMCnet] updating Olga By: cbryan on Fri, 07 March 2014 20:12
		Re: [GMCnet] updating Olga By: Bullitthead on Fri, 07 March 2014 20:43
		Re: [GMCnet] updating Olga By: k2gkk on Fri, 07 March 2014 21:00
		Re: [GMCnet] updating Olga By: Olly Schmidt on Sat, 08 March 2014 02:20
		Re: [GMCnet] updating Olga By: cbryan on Sat, 08 March 2014 06:25
		Re: [GMCnet] updating Olga By: cbryan on Sat, 08 March 2014 06:35
		Re: [GMCnet] updating Olga By: USAussie on Sat, 08 March 2014 07:15
		OT, Re: Olga illness some ramblings to R. Mueller et al. By: cbryan on Mon, 10 March 2014 16:20
		Re: [GMCnet] OT, Re: Olga illness some ramblings to R. Mueller et al. By: Kingsley Coach on Mon, 10 March 2014 17:15
		Re: [GMCnet] back pain (Hijacked thread) By: jhbridges on Wed, 12 March 2014 07:30
		Re: [GMCnet] back pain (Hijacked thread) By: k2gkk on Wed, 12 March 2014 09:48
		Re: [GMCnet] updating Olga By: Olly Schmidt on Sat, 08 March 2014 06:49
		Re: [GMCnet] updating Olga By: jhbridges on Fri, 07 March 2014 19:58
		Re: updating Olga By: Chr$ on Sun, 16 March 2014 10:25
		Re: updating Olga By: SeanKidd on Sun, 16 March 2014 08:17

Previous Topic:	[GMCnet] Have photo of what I did to get steel 16" rims on. Can E-mail photo
Next Topic:	Re: [GMCnet] updating Olga

Goto Forum:

-=] Back to Top [=-

Current Time: Fri Oct 04 02:24:34 CDT 2024

Total time taken to generate the page: 0.01535 seconds