Home » Public Forums » GMCnet » Oil galley plug
|
Re: [GMCnet] Oil galley plug [message #237385 is a reply to message #237374] |
Fri, 24 January 2014 23:06 |
emerystora
Messages: 4442 Registered: January 2004
Karma: 13
|
Senior Member |
|
|
The factory drilled the plug. It is shown in the GMC Maintenance Manual.
Dick Paterson has said in his engine rebuilding seminars that some people use the wrong plug, one without a hole, and the distributor gear won't get enough oil. It has nothing to do with the RPM of the engine or the volume of the oil pump.
Emery Stora
On Jan 24, 2014, at 9:17 PM, Bill Dolinsky <Wildbillnick@yahoo.com> wrote:
>
>
> Coming from no olds experience I am just thinking there should be enough oil sloshing around if the engine runs out of oil at 6000 rpm. However if you have a surplus volume yes I wouldn't have a problem drilling a plug to oil a distributor gear. It just like I picked up ac couple continental O-470 aircraft engines for my next airboat. Big oil pump, these things can run with .008 main clearance so I drilled the case for piston squirters to reduce potential for detonation. New bearings went in and Newer cases have them I found out. Second engine I bored the case for 520 jugs and isn't together yet but prioritys change. I don't see IMO a burning issue if you don't drill it, I don't see a problem at all if you do drill the plug.
> --
> Bill Dolinsky
> Edmonton, Alberta, Canada
> 1977 Kingsley TZE167V102169
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
Re: [GMCnet] Oil galley plug [message #237429 is a reply to message #237374] |
Sat, 25 January 2014 10:01 |
Jim Bounds
Messages: 842 Registered: January 2004
Karma: 0
|
Senior Member |
|
|
Original motors we have opened up do not have this hole. This is why after much thought about it we are not doing it. I feel it's a hi performance option those hi rev boyd so-- that's not for us. I want a rock solid hunk of metal that runs on regular gas, can accept any oil and produces it's best performance under 3000rpm. No chrome, original valve covers, and all other visible parts. Needs to fire every time and have Bubba & Scooter be able to work on it. With or without the hole makes little difference, if GM felt it needed to be there, they would have done it even on Chevys!
Jim Bounds
-------------------
On Friday, January 24, 2014 11:17 PM, Bill Dolinsky <Wildbillnick@yahoo.com> wrote:
Coming from no olds experience I am just thinking there should be enough oil sloshing around if the engine runs out of oil at 6000 rpm. However if you have a surplus volume yes I wouldn't have a problem drilling a plug to oil a distributor gear. It just like I picked up ac couple continental O-470 aircraft engines for my next airboat. Big oil pump, these things can run with .008 main clearance so I drilled the case for piston squirters to reduce potential for detonation. New bearings went in and Newer cases have them I found out. Second engine I bored the case for 520 jugs and isn't together yet but prioritys change. I don't see IMO a burning issue if you don't drill it, I don't see a problem at all if you do drill the plug.
--
Bill Dolinsky
Edmonton, Alberta, Canada
1977 Kingsley TZE167V102169
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
Re: [GMCnet] Oil galley plug [message #237466 is a reply to message #237429] |
Sat, 25 January 2014 16:54 |
|
USAussie
Messages: 15912 Registered: July 2007 Location: Sydney, Australia
Karma: 6
|
Senior Member |
|
|
Jim,
Ref: Maintenance Manual X-7525 / Section 6A / Page 6A/58 CAMSHAFT BEARINGS / Figure 65 / Camshaft and Oil Gallery Plugs
The left hand rear oil gallery plug is not shown. It is a threaded plug in the end of the left gallery just rearward of the
distributor. A small hole is provided in the plug for distributor lubrication. The cup plug shown provides access to the threaded
plug.
Ref: Parts book 78Z / Section 8 Engine / Page 8-2 CYLINDER BLOCK, CRANKSHAFT, OIL PAN
Page 8-4 / Key 31 - Qty - 1 / P/N - 588927 / Description - PLUG, camshaft rear bearing
Page 8-4 / Key 32 / Qty - 2 / P/N - None listed / Description - PLUG-oil passage (RH & LH)
Observations / Comments:
The MM notes; "A small hole is provided in the plug for distributor lubrication." Yet the PB does not provide a part number for
either of the plugs which IIRC means "local purchase." That is strange since they MM does not provide the diameter of that hole.
Things that make you go Hmmmmm?
Regards,
Rob M.
Sydney, Australia
AUS '75 Avion - The Blue Streak TZE365V100428
USA '75 Avion - Double Trouble TZE365V100426
PS - I checked MM X-7625 and found NADA, however, in MM X-7725 on page 6A-80 the same info noted in X-7725 is provided.
-----Original Message-----
From: Jim Bounds
Original motors we have opened up do not have this hole. This is why after much thought about it we are not doing it. I feel it's
a hi performance option those hi rev boyd so-- that's not for us. I want a rock solid hunk of metal that runs on regular gas, can
accept any oil and produces it's best performance under 3000rpm. No chrome, original valve covers, and all other visible parts.
Needs to fire every time and have Bubba & Scooter be able to work on it. With or without the hole makes little difference, if GM
felt it needed to be there, they would have done it even on Chevys!
Jim
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Regards,
Rob M. (USAussie)
The Pedantic Mechanic
Sydney, Australia
'75 Avion - AUS - The Blue Streak TZE365V100428
'75 Avion - USA - Double Trouble TZE365V100426
|
|
|
Re: [GMCnet] Oil galley plug [message #237752 is a reply to message #237212] |
Tue, 28 January 2014 06:58 |
jhbridges
Messages: 8412 Registered: May 2011 Location: Braselton ga
Karma: -74
|
Senior Member |
|
|
Yes, in a 300 CID Furd 6. Oil pump froze and took the drive gear (and the quill shaft) out. Probably saved the rest of the engine.
--johnny
From: Sean Kidd <fiatkidd@yahoo.com>
To: gmclist@temp.gmcnet.org
Sent: Thursday, January 23, 2014 7:47 PM
Subject: Re: [GMCnet] Oil galley plug
Has anyone ever experienced a dizzy gear failure?
--
Sean and Stephanie
73 Ex-CanyonLands 26' #317 "Oliver"
Hubler 1-Ton, Quad-Bags, Rear Disc, Reaction Arms,
Fluorescent Mineral Capital of the World, New Jersey
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Foolish Carriage, 76 26' Eleganza(?) with beaucoup mods and add - ons.
Braselton, Ga.
I forgive them all, save those who hurt the dogs. They must answer to me in hell
|
|
|
Re: [GMCnet] Oil galley plug [message #237772 is a reply to message #237374] |
Tue, 28 January 2014 08:40 |
jhbridges
Messages: 8412 Registered: May 2011 Location: Braselton ga
Karma: -74
|
Senior Member |
|
|
Bill, aren't the TSIO series engines alreadty fitted with oil spray to the pistons? We sold a bunch of airboat engines into the Everglades (All stamped NOT AIRWORTHY) when the welders were learning how. GSO-490 Lycs if memory serves.
--johnny
'76 23' transmode norris\
From: Bill Dolinsky <Wildbillnick@yahoo.com>
To: gmclist@temp.gmcnet.org
Sent: Friday, January 24, 2014 11:17 PM
Subject: Re: [GMCnet] Oil galley plug
Coming from no olds experience I am just thinking there should be enough oil sloshing around if the engine runs out of oil at 6000 rpm. However if you have a surplus volume yes I wouldn't have a problem drilling a plug to oil a distributor gear. It just like I picked up ac couple continental O-470 aircraft engines for my next airboat. Big oil pump, these things can run with .008 main clearance so I drilled the case for piston squirters to reduce potential for detonation. New bearings went in and Newer cases have them I found out. Second engine I bored the case for 520 jugs and isn't together yet but prioritys change. I don't see IMO a burning issue if you don't drill it, I don't see a problem at all if you do drill the plug.
--
Bill Dolinsky
Edmonton, Alberta, Canada
1977 Kingsley TZE167V102169
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Foolish Carriage, 76 26' Eleganza(?) with beaucoup mods and add - ons.
Braselton, Ga.
I forgive them all, save those who hurt the dogs. They must answer to me in hell
|
|
|
Re: [GMCnet] Oil galley plug [message #237778 is a reply to message #237772] |
Tue, 28 January 2014 09:00 |
|
Matt Colie
Messages: 8547 Registered: March 2007 Location: S.E. Michigan
Karma: 7
|
Senior Member |
|
|
Johnny Bridges wrote on Tue, 28 January 2014 09:40 | Bill, aren't the TSIO series engines alreadty fitted with oil spray to the pistons? We sold a bunch of airboat engines into the Everglades (All stamped NOT AIRWORTHY) when the welders were learning how. GSO-490 Lycs if memory serves.
--johnny
From: Bill Dolinsky
Subject: Re: [GMCnet] Oil galley plug
Coming from no olds experience I am just thinking there should be enough oil sloshing around if the engine runs out of oil at 6000 rpm. However if you have a surplus volume yes I wouldn't have a problem drilling a plug to oil a distributor gear. It just like I picked up ac couple continental O-470 aircraft engines for my next airboat. Big oil pump, these things can run with .008 main clearance so I drilled the case for piston squirters to reduce potential for detonation. New bearings went in and Newer cases have them I found out. Second engine I bored the case for 520 jugs and isn't together yet but prioritys change. I don't see IMO a burning issue if you don't drill it, I don't see a problem at all if you do drill the plug.
--
Bill Dolinsky
|
Hey Guys,
Lots of heavy duty diesels have piston coolers, and so do all of the MB turbo-diesel passcar engines. There is a rule in engine design....
If you need cooling or lube oil there, put it there.
Don't count on it happening by chance, because when you really need it, it won't be there.
If you look around, you will find a few passcar motors that have a strange little groove in the upper rod shell that is matched in the rod forging. This is to put lube oil both on the thrust face of the cylinder wall and under the piston crown for cooling.
Matt - the engine lab refugee
Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL, GMCES
Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum Brakes with Applied Control Arms
SE Michigan - Near DTW - Twixt A2 and Detroit
|
|
|
Re: [GMCnet] Oil galley plug [message #237926 is a reply to message #237778] |
Wed, 29 January 2014 08:47 |
jhbridges
Messages: 8412 Registered: May 2011 Location: Braselton ga
Karma: -74
|
Senior Member |
|
|
Matt, VW did cooler sprays on the turbo 1`600s but not on the NA 1600s (Both Diesels). They use a different block, which has led to grief when people triedto field add the turbo to the NAs.
--johnny
________________________________
From: Matt Colie <matt7323tze@gmail.com>
To: gmclist@temp.gmcnet.org
Sent: Tuesday, January 28, 2014 10:00 AM
Subject: Re: [GMCnet] Oil galley plug
Johnny Bridges wrote on Tue, 28 January 2014 09:40
> Bill, aren't the TSIO series engines alreadty fitted with oil spray to the pistons? We sold a bunch of airboat engines into the Everglades (All stamped NOT AIRWORTHY) when the welders were learning how. GSO-490 Lycs if memory serves.
>
> --johnny
> From: Bill Dolinsky
> Subject: Re: [GMCnet] Oil galley plug
>
> Coming from no olds experience I am just thinking there should be enough oil sloshing around if the engine runs out of oil at 6000 rpm. However if you have a surplus volume yes I wouldn't have a problem drilling a plug to oil a distributor gear. It just like I picked up ac couple continental O-470 aircraft engines for my next airboat. Big oil pump, these things can run with .008 main clearance so I drilled the case for piston squirters to reduce potential for detonation. New bearings went in and Newer cases have them I found out. Second engine I bored the case for 520 jugs and isn't together yet but prioritys change. I don't see IMO a burning issue if you don't drill it, I don't see a problem at all if you do drill the plug.
> --
> Bill Dolinsky
Hey Guys,
Lots of heavy duty diesels have piston coolers, and so do all of the MB turbo-diesel passcar engines. There is a rule in engine design....
If you need cooling or lube oil there, put it there.
Don't count on it happening by chance, because when you really need it, it won't be there.
If you look around, you will find a few passcar motors that have a strange little groove in the upper rod shell that is matched in the rod forging. This is to put lube oil both on the thrust face of the cylinder wall and under the piston crown for cooling.
Matt - the engine lab refugee
--
Matt & Mary Colie - Members GMCMI, GMCES Going to MontgomeryThe majestic, once snow covered glacier Chaumière is in for the winter.
'73 Glacier 23 With 4 Rear Brakes that pull as they should
SE Michigan - Twixt A2 and Detroit
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Foolish Carriage, 76 26' Eleganza(?) with beaucoup mods and add - ons.
Braselton, Ga.
I forgive them all, save those who hurt the dogs. They must answer to me in hell
|
|
|
Re: [GMCnet] Oil galley plug [message #237937 is a reply to message #237926] |
Wed, 29 January 2014 09:35 |
GMC_LES
Messages: 569 Registered: October 2009 Location: Montreal
Karma: 0
|
Senior Member |
|
|
Pretty much all of the VW/AUDI turbo engines (gas and diesel) have the piston oiler nozzles.
The 2.3 TD that Ford put in their 85-87 Ranger also had them.
Les Burt
Montreal
1975 Eleganza 26ft
A work in Progress
On Jan 29, 2014, at 9:47 AM, Johnny Bridges <jhbridges@ymail.com> wrote:
Matt, VW did cooler sprays on the turbo 1`600s but not on the NA 1600s (Both Diesels). They use a different block, which has led to grief when people triedto field add the turbo to the NAs.
--johnny
________________________________
From: Matt Colie <matt7323tze@gmail.com>
To: gmclist@temp.gmcnet.org
Sent: Tuesday, January 28, 2014 10:00 AM
Subject: Re: [GMCnet] Oil galley plug
Johnny Bridges wrote on Tue, 28 January 2014 09:40
> Bill, aren't the TSIO series engines alreadty fitted with oil spray to the pistons? We sold a bunch of airboat engines into the Everglades (All stamped NOT AIRWORTHY) when the welders were learning how. GSO-490 Lycs if memory serves.
>
> --johnny
> From: Bill Dolinsky
> Subject: Re: [GMCnet] Oil galley plug
>
> Coming from no olds experience I am just thinking there should be enough oil sloshing around if the engine runs out of oil at 6000 rpm. However if you have a surplus volume yes I wouldn't have a problem drilling a plug to oil a distributor gear. It just like I picked up ac couple continental O-470 aircraft engines for my next airboat. Big oil pump, these things can run with .008 main clearance so I drilled the case for piston squirters to reduce potential for detonation. New bearings went in and Newer cases have them I found out. Second engine I bored the case for 520 jugs and isn't together yet but prioritys change. I don't see IMO a burning issue if you don't drill it, I don't see a problem at all if you do drill the plug.
> --
> Bill Dolinsky
Hey Guys,
Lots of heavy duty diesels have piston coolers, and so do all of the MB turbo-diesel passcar engines. There is a rule in engine design....
If you need cooling or lube oil there, put it there.
Don't count on it happening by chance, because when you really need it, it won't be there.
If you look around, you will find a few passcar motors that have a strange little groove in the upper rod shell that is matched in the rod forging. This is to put lube oil both on the thrust face of the cylinder wall and under the piston crown for cooling.
Matt - the engine lab refugee
--
Matt & Mary Colie - Members GMCMI, GMCES Going to MontgomeryThe majestic, once snow covered glacier Chaumière is in for the winter.
'73 Glacier 23 With 4 Rear Brakes that pull as they should
SE Michigan - Twixt A2 and Detroit
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Les Burt
Montreal
1975 Eleganza 26ft
A work in Progress
|
|
|
|
|
Goto Forum:
Current Time: Fri Sep 27 12:31:07 CDT 2024
Total time taken to generate the page: 0.01874 seconds
|