Home » Public Forums » GMCnet » Running a new ground to the ECM
Running a new ground to the ECM [message #233945] |
Wed, 25 December 2013 00:58 |
|
Richard RV
Messages: 631 Registered: July 2012 Location: Full-timer for 12 years, ...
Karma: -17
|
Senior Member |
|
|
I'm slaying the sitting-coach-lot-of-work-done-gremlins one at a time, and I'm trying to work my way through some electrical issues. I'm pretty sure I have a/some bad ground(s) causing 12 volts on a number of ECM sensor ground pins that should be reading 0 volts, most gauges not working, etc.
I read a post Ken Burton wrote some time ago about running a new ground to the ECM while trying to help a GMCer limp home from a rally. How exactly is that done? Do I just select the wires which are supposed to be ground just before the ECM connectors and splice on a wire to each one running to the engine block? Is there another way to do it, maybe a single wire? I don't want to start hacking into the harness if it's not really necessary.
thanks
Richard
'77 Birchaven TZE...777;
'76 Palm Beach under construction;
‘76 Edgemont waiting its turn
|
|
|
Re: Running a new ground to the ECM [message #233950 is a reply to message #233945] |
Wed, 25 December 2013 02:04 |
Ken Burton
Messages: 10030 Registered: January 2004 Location: Hebron, Indiana
Karma: 10
|
Senior Member |
|
|
Richard,
I was unfamiliar with the ECM we were working with. After talking to a GM mechanic friend on the phone he suggested that many of the intermittent problems he had with ECMs of that era were grounding issues. I had no wiring diagrams and no first hand knowledge of that ECM. I could not figure out where the wires went once they went though the hole in the floor under the driver's seat where the ECM was located. So my solution was to run a new 16 gauge ground wire from the outside case of the ECM through hole in the floor direct to an engine bolt directly below the hole. It probably was a bolt on the intake manifold. I do not know if that fixed the problem or not because we fixed several other things like wire crimps on the the distributor at the same time. We also replaced a bunch of tune up parts at the same time.
I do not know it this helped you or not, but the engine is the master ground for the 12 volt system. So however you decide to hook up to the ECM, run the other end of the ground wire direct to the engine somewhere.
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
|
|
|
Re: Running a new ground to the ECM [message #233951 is a reply to message #233950] |
Wed, 25 December 2013 07:45 |
mrgmc3
Messages: 210 Registered: September 2013 Location: W Washington
Karma: 2
|
Senior Member |
|
|
If it is like most GM ECMs you should have a couple pins dedicated to grounds. The goal is to have the ECM, and power supply, and all sensors on the same ground plane.
If you have a diagram for the ECM you'll see which pins are grounds. If not then any black wire in the OE harness will be a ground. You need those pins grounded, not just the case.
You should also have a good heavy ground strap running from the block or head to frame (GM typically uses a bare braided flat copper strap for this) and from the engine battery to frame or engine (not sure where the OE GMC engine battery ground is located yet). You need the engine battery, the engine block, and ECM to be grounded together (same plane). Otherwise voltage differentials will seek ways of finding that plane by traveling through other ECM devices and circuits. You can imagine what happens when current goes through a circuit that was meant for a sensitive 5v signal like a sensor, or the o2 sensor which operates on 1 V.
Chris Geils - Twin Cities / W Wa
1978 26' Kingsley w/ very few mods; PD9040, aux trans cooler, one repaint in stock colors, R134a, Al rad, Alcoas, 54k mi
|
|
|
Re: Running a new ground to the ECM [message #233952 is a reply to message #233951] |
Wed, 25 December 2013 08:04 |
Ken Burton
Messages: 10030 Registered: January 2004 Location: Hebron, Indiana
Karma: 10
|
Senior Member |
|
|
The engine battery ground cable goes to the engine, NOT the frame. The master ground on a GMC (engine side) is the engine, NOT the frame. Yes there is a strap between the engine and the frame for cross connection the the house electrical system. It is located on the back of the transmission and is connected around the rear transmission mount. None of this has anything to do with grounding the ECM. The ECM ground needs to go direct to the engine.
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
|
|
|
Re: Running a new ground to the ECM [message #233958 is a reply to message #233952] |
Wed, 25 December 2013 10:27 |
mrgmc3
Messages: 210 Registered: September 2013 Location: W Washington
Karma: 2
|
Senior Member |
|
|
The engine is the "master" ground in any automotive ECM. I'll repeat myself because the discussion of frame grounds got us a little sidetracked;
"You need the engine battery, the engine block, and ECM to be grounded together" and for the ECM this means the ground pins in the connector not just the ECM case. The case is not a reliable ground for items on the board.
Chris Geils - Twin Cities / W Wa
1978 26' Kingsley w/ very few mods; PD9040, aux trans cooler, one repaint in stock colors, R134a, Al rad, Alcoas, 54k mi
|
|
|
Re: Running a new ground to the ECM [message #233975 is a reply to message #233958] |
Wed, 25 December 2013 19:12 |
Ken Burton
Messages: 10030 Registered: January 2004 Location: Hebron, Indiana
Karma: 10
|
Senior Member |
|
|
mrgmc3 wrote on Wed, 25 December 2013 10:27 | The engine is the "master" ground in any automotive ECM. I'll repeat myself because the discussion of frame grounds got us a little sidetracked;
"You need the engine battery, the engine block, and ECM to be grounded together" and for the ECM this means the ground pins in the connector not just the ECM case. The case is not a reliable ground for items on the board.
|
OK, I misread or misunderstood. We are in agreement.
Ken
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
|
|
|
|
Re: [GMCnet] Running a new ground to the ECM [message #233981 is a reply to message #233980] |
Wed, 25 December 2013 20:30 |
|
Richard RV
Messages: 631 Registered: July 2012 Location: Full-timer for 12 years, ...
Karma: -17
|
Senior Member |
|
|
mickeysss wrote on Wed, 25 December 2013 19:20 | what is ECM? m. ca. 77 pb.
|
It's the engine computer that controls the aftermarket fuel injection I have, and is also referred to by different acronyms...ECU, PCM, etc.
Richard
'77 Birchaven TZE...777;
'76 Palm Beach under construction;
‘76 Edgemont waiting its turn
|
|
|
Re: Running a new ground to the ECM [message #233983 is a reply to message #233975] |
Wed, 25 December 2013 20:35 |
|
Richard RV
Messages: 631 Registered: July 2012 Location: Full-timer for 12 years, ...
Karma: -17
|
Senior Member |
|
|
Gentlemen,
Okay, I understand about running the ground to the engine, but I'm still a bit hazy on the connections at the ECM. I've read about repinning at the connectors using a little punch type tool to remove the pins, but I'm not sure if that's what I should be doing for what may be a temporary repair/test. I thought that stripping some insulation along the ground wire(s) some bit back from the ECM connectors and running ground(s) to the engine from there would work. Does that sound like a reasonable way to do it, or is there a better way?
Richard
'77 Birchaven TZE...777;
'76 Palm Beach under construction;
‘76 Edgemont waiting its turn
[Updated on: Wed, 25 December 2013 20:36] Report message to a moderator
|
|
|
Re: [GMCnet] Running a new ground to the ECM [message #233994 is a reply to message #233980] |
Wed, 25 December 2013 22:42 |
sgltrac
Messages: 2797 Registered: April 2011
Karma: 1
|
Senior Member |
|
|
Engine control module
Todd Sullivan
Sully
77 royale
Seattle
> On Dec 25, 2013, at 6:21 PM, Mickey Space Ship Shuttle <mickeysss@me.com> wrote:
>
> what is ECM? m. ca. 77 pb.
>
>
>> On Dec 25, 2013, at 5:12 PM, Ken Burton wrote:
>>
>>
>>
>> mrgmc3 wrote on Wed, 25 December 2013 10:27
>>> The engine is the "master" ground in any automotive ECM. I'll repeat myself because the discussion of frame grounds got us a little sidetracked;
>>> "You need the engine battery, the engine block, and ECM to be grounded together" and for the ECM this means the ground pins in the connector not just the ECM case. The case is not a reliable ground for items on the board.
>>
>>
>>
>> OK, I misread or misunderstood. We are in agreement.
>>
>> Ken
>> --
>> Ken Burton - N9KB
>> 76 Palm Beach
>> Hebron, Indiana
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Sully
77 Royale basket case.
Future motorhome land speed record holder(bucket list)
Seattle, Wa.
|
|
|
Re: Running a new ground to the ECM [message #233997 is a reply to message #233983] |
Wed, 25 December 2013 23:31 |
mrgmc3
Messages: 210 Registered: September 2013 Location: W Washington
Karma: 2
|
Senior Member |
|
|
Ken,
No problem. I understand GM ECMs but am a little hazy on a lot of the mechanization of the GMC (such as ground routing) having only owned it for 4 months!
Richard V. wrote on Wed, 25 December 2013 20:35 | Gentlemen,
Okay, I understand about running the ground to the engine, but I'm still a bit hazy on the connections at the ECM. I've read about repinning at the connectors using a little punch type tool to remove the pins, but I'm not sure if that's what I should be doing for what may be a temporary repair/test. I thought that stripping some insulation along the ground wire(s) some bit back from the ECM connectors and running ground(s) to the engine from there would work. Does that sound like a reasonable way to do it, or is there a better way?
Richard
|
Richard,
I'll assume that you are using a 90s vintage GM v8 ECM and that you have some portion of the wiring harness and ECM connectors (and that you don't have a wiring diagram for the donor). If this is the case any wire in the ECM harness that is all black (no stripe) will be a ground. These should go to a clean ring connector on a cyl head, block or Trans case. You don't need to repin them at the ECM, just extend the wires to reach your new ground location. I would not recommend pulling one of the ECM connectors apart unless you have the correct terminal tools and extra terminals. They are available from commercial sources like Power and Signal or Mouser.
Chris Geils - Twin Cities / W Wa
1978 26' Kingsley w/ very few mods; PD9040, aux trans cooler, one repaint in stock colors, R134a, Al rad, Alcoas, 54k mi
|
|
|
Goto Forum:
Current Time: Fri Jan 24 17:52:57 CST 2025
Total time taken to generate the page: 0.01264 seconds
|