GMCforum
For enthusiast of the Classic GMC Motorhome built from 1973 to 1978. A web-based mirror of the GMCnet mailing list.
Home » Public Forums » GMCnet » Need a measurement....
Need a measurement.... [message #231091] Sun, 24 November 2013 16:44 Go to next message
quadracerx1 is currently offline  quadracerx1   United States
Messages: 207
Registered: April 2013
Location: Puyallup, Washington
Karma: 1
Senior Member
I need to get a couple measurements from someone with a gutted GMC.. working with a 75 GMC so hope the measurements will correspond..

1) Height of rear wheelwell.

2) Height from rear floor to ceiling center.

Thanks,

Steve

75 26' GMC Glenbrook Puyallup, Washington

Report message to a moderator

Re: Need a measurement.... [message #231092 is a reply to message #231091] Sun, 24 November 2013 16:45 Go to previous messageGo to next message
quadracerx1 is currently offline  quadracerx1   United States
Messages: 207
Registered: April 2013
Location: Puyallup, Washington
Karma: 1
Senior Member
Someone had a factory drawing that showed all the interior dimensions but damned if I can find it?

Thanks,

Steve

75 26' GMC Glenbrook Puyallup, Washington

Report message to a moderator

Re: Need a measurement.... [message #231097 is a reply to message #231092] Sun, 24 November 2013 16:58 Go to previous messageGo to next message
A Hamilto is currently offline  A Hamilto   United States
Messages: 4508
Registered: April 2011
Karma: 39
Senior Member
quadracerx1 wrote on Sun, 24 November 2013 16:45

Someone had a factory drawing that showed all the interior dimensions but damned if I can find it?

Thanks,

Steve
Is there anything here that helps?

http://www.bdub.net/GMCdrawings/

Report message to a moderator

Re: Need a measurement.... [message #231105 is a reply to message #231097] Sun, 24 November 2013 17:46 Go to previous messageGo to next message
Harry is currently offline  Harry   Canada
Messages: 1888
Registered: October 2007
Location: Victoria, BC CANADA
Karma: 3
Senior Member
I can see 17.09 inches to the top of the wheel well, but can't tell if it's from the top of the floor or not.

I just went and measured mine. 17.25" from the plywood floor.

[Updated on: Sun, 24 November 2013 17:54]

Report message to a moderator

Re: Need a measurement.... [message #231107 is a reply to message #231105] Sun, 24 November 2013 17:57 Go to previous messageGo to next message
Harry is currently offline  Harry   Canada
Messages: 1888
Registered: October 2007
Location: Victoria, BC CANADA
Karma: 3
Senior Member
Approx. 77" -78" inside to ceiling from floor.

Report message to a moderator

Re: Need a measurement.... [message #231147 is a reply to message #231091] Sun, 24 November 2013 22:19 Go to previous message
quadracerx1 is currently offline  quadracerx1   United States
Messages: 207
Registered: April 2013
Location: Puyallup, Washington
Karma: 1
Senior Member
Thanks guys...

That's exactly what I needed... Still trying to decide about the car trailer concept... I will need to build long ramps and a subfloor (or runners) above the rear wheelwells if it is going to work... Not sure it will?

Any thoughts?

Thanks again...

Steve

75 26' GMC Glenbrook Puyallup, Washington

Report message to a moderator

Previous Topic: Re: [GMCnet] Can a 747 take off in 6000 feet?
Next Topic: electric cord and city water access door sealing
Goto Forum:
  


Current Time: Mon Nov 04 22:04:04 CST 2024

Total time taken to generate the page: 0.03536 seconds
.:: Contact :: Home ::.

Powered by: FUDforum 3.1.1.
Copyright ©2001-2021 FUDforum Bulletin Board Software