It has begun [message #229590] |
Tue, 12 November 2013 19:16 |
kerry pinkerton
Messages: 2565 Registered: July 2012 Location: Harvest, Al
Karma: 15
|
Senior Member |
|
|
The bed frame with the hideaway table was only one part of my winters interior project. The overhead cabinets behind the cockpit have been removed as will the overhead kitchen cabinets.
Wood had been purchased and cabinet making will commence shortly...probably tomorrow. Today we went looking at store bought cabinets and I decided it was simpler to build the doors the size I want than modify new stuff...considerably less expensive also.
Once the cabinets are built and test fit but before they are installed permanently, I'll pull the drivers side wall and insulate before recovering with FRP with glued on vinyl. Already did the passenger side.
Headliner will be FRP with something glued to it. Thinking a white or off white vinyl.
But once the wall and ceiling are out and before ANYTHING goes in, I'm going to find and stop any leaks.
Kerry Pinkerton - North Alabama
Had 5 over the years. Currently have a '06 Fleetwood Discovery 39L
|
|
|
|
Re: It has begun [message #229613 is a reply to message #229590] |
Tue, 12 November 2013 20:55 |
Dennis S
Messages: 3046 Registered: November 2005
Karma: 2
|
Senior Member |
|
|
Kerry Pinkerton wrote on Tue, 12 November 2013 19:16 | The bed frame with the hideaway table was only one part of my winters interior project. The overhead cabinets behind the cockpit have been removed as will the overhead kitchen cabinets.
Wood had been purchased and cabinet making will commence shortly...probably tomorrow. Today we went looking at store bought cabinets and I decided it was simpler to build the doors the size I want than modify new stuff...considerably less expensive also.
Once the cabinets are built and test fit but before they are installed permanently, I'll pull the drivers side wall and insulate before recovering with FRP with glued on vinyl. Already did the passenger side.
Headliner will be FRP with something glued to it. Thinking a white or off white vinyl.
But once the wall and ceiling are out and before ANYTHING goes in, I'm going to find and stop any leaks.
|
Armand's remodel photo album is one I refer to for ideas...
here is one photo of his new kitchen cabinet...
http://www.gmcmhphotos.com/photos/interior-remodel-phase-i/p34654-kitchen-base-cabinet-w.html
and here is the complete ablbum
http://www.gmcmhphotos.com/photos/g5500-interior-remodel-phase-i.html
He has another for the rear bedroom remodel.
Dennis
Dennis S
73 Painted Desert 230
Memphis TN Metro
|
|
|
Re: It has begun [message #229667 is a reply to message #229590] |
Wed, 13 November 2013 09:29 |
|
Richard RV
Messages: 631 Registered: July 2012 Location: Full-timer for 12 years, ...
Karma: -17
|
Senior Member |
|
|
Kerry,
there are a number of cabinet parts outfits that furnish the parts unfinished or prefinished, assembled or RTA. For cabinet doors, drawer fronts and dovetailed drawer boxes it's tough to beat their delivery speed, quality and finish, and the prices aren't bad either. Custom-sizing is what they do, so you won't get beat up for having oddball dimensions. Lots of finishes, lots of door face and edge styles.
On a larger project, such as a residential kitchen, it might make more sense to build the stuff yourself, or have a local do it for you. Considering what your time is worth while you could be working on another part of the project, and the small amount of stuff required for a GMC, it's well worth looking into what it would cost through CabParts or another outfit close to your neck of the woods.
Richard
'77 Birchaven TZE...777;
'76 Palm Beach under construction;
‘76 Edgemont waiting its turn
[Updated on: Wed, 13 November 2013 09:33] Report message to a moderator
|
|
|