Home » Public Forums » GMCnet » [GMCnet] Dropping the fuel tanks and replacing rubber fuel lines on the Barn Queen
[GMCnet] Dropping the fuel tanks and replacing rubber fuel lines on the Barn Queen [message #228936] |
Fri, 08 November 2013 13:31 |
Robin Hood
Messages: 1078 Registered: April 2011
Karma: 3
|
Senior Member |
|
|
20 years sitting in a barn. I do not want to, but I feel that I must do
this. The rubber lines are sure to be dry rotted, and there's a good chance
that the tanks may be full of rust or something.
The tanks need to be inspected, yes? And I must drop them to do this, yes?
And I need to drop them in order to replace all the rubber anyway, yes?
I think I will buy some 2x12s and build a ramp that will put the bottom of
the tires a foot and a half off the ground. That will give me enough room
to get underneath and do things.
I will be doing this in the driveway of my house. The weather is pleasant
enough, there are no wasps, and it's convenient. I might ougt to "strike
while the iron is hot" as they say, especially since my dear sweet wife is
so enthusiastic.
Comments or suggestions? I believe the tank dropping procedure is in X7725
somewhere? It wasn' tin the main manual that I downloaded, I need to go
find it. I would love to hear some been-there-done-thats from those that
have done this before already. Comments, suggestions, attaboys etc are all
welcome. There will be video.
Hoses will be replaced with corn-proof hose.
--
Robin Hood
Jackson, MS
2013 Subaru Outback "Top Flight"
1968 Pontiac Catalina "The Cheshire Cat"
1978 GMC Royale motorhome "Pinto Bean"
1977 GMC Palm Beach motorhome "Barn Queen"
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
Re: [GMCnet] Dropping the fuel tanks and replacing rubber fuel lines on the Barn Queen [message #228942 is a reply to message #228936] |
Fri, 08 November 2013 14:07 |
jhbridges
Messages: 8412 Registered: May 2011 Location: Braselton ga
Karma: -74
|
Senior Member |
|
|
I use 4x4s (because siomeone gave me a truckload of them) but whatever, crib the thing up solidly. Not like you had it in the pic waiting for the brake mechanic. If it falls on you, you ain't coming back out from under it again.
--johnny
From: Robin Hood <loxley@gmail.com>
To: "gmclist@temp.gmcnet.org" <gmclist@temp.gmcnet.org>
Sent: Friday, November 8, 2013 2:31 PM
Subject: [GMCnet] Dropping the fuel tanks and replacing rubber fuel lines on the Barn Queen
20 years sitting in a barn. I do not want to, but I feel that I must do
this. The rubber lines are sure to be dry rotted, and there's a good chance
that the tanks may be full of rust or something.
The tanks need to be inspected, yes? And I must drop them to do this, yes?
And I need to drop them in order to replace all the rubber anyway, yes?
I think I will buy some 2x12s and build a ramp that will put the bottom of
the tires a foot and a half off the ground. That will give me enough room
to get underneath and do things.
I will be doing this in the driveway of my house. The weather is pleasant
enough, there are no wasps, and it's convenient. I might ougt to "strike
while the iron is hot" as they say, especially since my dear sweet wife is
so enthusiastic.
Comments or suggestions? I believe the tank dropping procedure is in X7725
somewhere? It wasn' tin the main manual that I downloaded, I need to go
find it. I would love to hear some been-there-done-thats from those that
have done this before already. Comments, suggestions, attaboys etc are all
welcome. There will be video.
Hoses will be replaced with corn-proof hose.
--
Robin Hood
Jackson, MS
2013 Subaru Outback "Top Flight"
1968 Pontiac Catalina "The Cheshire Cat"
1978 GMC Royale motorhome "Pinto Bean"
1977 GMC Palm Beach motorhome "Barn Queen"
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Foolish Carriage, 76 26' Eleganza(?) with beaucoup mods and add - ons.
Braselton, Ga.
I forgive them all, save those who hurt the dogs. They must answer to me in hell
|
|
|
|
Re: [GMCnet] Dropping the fuel tanks and replacing rubber fuel lines on the Barn Queen [message #228945 is a reply to message #228936] |
Fri, 08 November 2013 14:32 |
|
ljdavick
Messages: 3548 Registered: March 2007 Location: Fremont, CA
Karma: -3
|
Senior Member |
|
|
Robin,
I took the coward's way out on the coach and had Jim K's folks replace all the soft lines. (My best tool is my checkbook.)
However on my daughter's Vanagon Westfalia, that had been sitting for 21 years, I replaced the fuel tank. I anticipated a heavy tank full of old fuel, however it had no liquid in it at all. I suspect it had evaporated, and the result was a tar-like goo that remained. For the GMC I would recommend finding a local shop that can boil and coat the tanks.
I would not get stuck in the "while I'm at it" game (too much.) For instance adding electric fuel pumps, though it will be nice to do at the time, is not in line with the primary goal of getting her on the road. A large fuel filter might not take too much time and might be beneficial, though if the tanks are cleaned and the hoses are new the need is lessened.
Here is some - while you're at it stuff that might be worthwhile - I really like the things guys are doing with port-holes in the floor so that they can access the tank opening. This would enable you to add the in-tank fuel pumps at a later time if you choose to. If any of your steel lines are clogged, corroded, or you just want to replace them, I would recommend PolyArmor < http://www.agscompany.com/automotive/brake-fuel-transmission-lines/poly-armour> It's very easy to work with, corrosion resistant, and should be available at your local Napa Auto parts, though they may not know it by name.
Don't forget the vent lines, the generator supply line, and the vapor canister and separator. Some have removed the vapor canister, I think it's a good thing to have. The idea of collecting fuel vapor when sitting and then sucking it into the carb to be burned is a good thing. The supply side has to be looked at too. Once all of this is back in place you'll be able to set the nozzle and fill the tanks whilst enjoying a cool beverage. Once the coach is running I expect you'll this quite often!
Good luck to you and enjoy the ride!
Larry Davick
Fremont, California
A Mystery Machine
'76 (ish) Palm Beach
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Larry Davick
A Mystery Machine
1976(ish) Palm Beach
Fremont, Ca
Howell EFI + EBL + Electronic Dizzy
|
|
|
|
Re: [GMCnet] Dropping the fuel tanks and replacing rubber fuel lines on the Barn Queen [message #228949 is a reply to message #228936] |
Fri, 08 November 2013 14:49 |
rcjordan
Messages: 1913 Registered: October 2012 Location: Elizabeth City, North Car...
Karma: 1
|
Senior Member |
|
|
>I would not get stuck in the "while I'm at it" game (too much.)
Yeah, my thought, too. You're the guy who was going to ship the coach off as a Burning Man sacrifice, right? If so, this is a big shift in trajectory and may need some "good times" logged in asap. That said, breaking down isn't a good time for anybody ..except maybe Ken H.
So maybe slush the tanks, replace the fuel lines and filters, mark the spots in the floor for access ports and take it around the block a few times, then out to a nearby state park or rv resort.
That's the best-case scenario, though, because the average rebooted vehicle soon starts to shake out some other problems. Whatever you do, I'd keep the wife appraised of the risks involved in having an adventure involving vintage vehicles.
SOLD 77 Royale Coachmen Side Dry Bath
76 Birchaven Coachmen Side Wet Bath
76 Eleganza
Elizabeth City, NC
[Updated on: Fri, 08 November 2013 14:51] Report message to a moderator
|
|
|
Re: [GMCnet] Dropping the fuel tanks and replacing rubber fuel lines onthe Barn Queen [message #228969 is a reply to message #228936] |
Fri, 08 November 2013 18:30 |
|
USAussie
Messages: 15912 Registered: July 2007 Location: Sydney, Australia
Karma: 6
|
Senior Member |
|
|
Robin,
The 20 year old lines are NOT compatible with ethanol, neither are 35 year old lines! ;-)
I think ramps that are 1 1/2 feet tall are a bit ambitious for a GMC to climb. Even with the air bags fully expanded I don't know if
you'd be able to clear the body sections behind the rear wheels. I assume you would be backing in towards your house to get up on
them and that would be a bit scary if something went wrong.
I just measured the ones that John Sharpe built, they are 8" high, 10" wide and 72" long and HEAVY!
I could have sworn that you had a set of wooden jack stands when I was over there helping you with the rear brakes. Why don't you
use them? If you want them higher add a few extra "steps."
Regards,
Rob M.
The Pedantic Mechanic
-----Original Message-----
From: Robin Hood
20 years sitting in a barn. I do not want to, but I feel that I must do
this. The rubber lines are sure to be dry rotted, and there's a good chance
that the tanks may be full of rust or something.
The tanks need to be inspected, yes? And I must drop them to do this, yes?
And I need to drop them in order to replace all the rubber anyway, yes?
I think I will buy some 2x12s and build a ramp that will put the bottom of
the tires a foot and a half off the ground. That will give me enough room
to get underneath and do things.
I will be doing this in the driveway of my house. The weather is pleasant
enough, there are no wasps, and it's convenient. I might ougt to "strike
while the iron is hot" as they say, especially since my dear sweet wife is
so enthusiastic.
Comments or suggestions? I believe the tank dropping procedure is in X7725
somewhere? It wasn' tin the main manual that I downloaded, I need to go
find it. I would love to hear some been-there-done-thats from those that
have done this before already. Comments, suggestions, attaboys etc are all
welcome. There will be video.
Hoses will be replaced with corn-proof hose.
--
Robin
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Regards,
Rob M. (USAussie)
The Pedantic Mechanic
Sydney, Australia
'75 Avion - AUS - The Blue Streak TZE365V100428
'75 Avion - USA - Double Trouble TZE365V100426
|
|
|
Re: [GMCnet] Dropping the fuel tanks and replacing rubber fuel lines on the Barn Queen [message #228979 is a reply to message #228936] |
Fri, 08 November 2013 19:40 |
Galen
Messages: 146 Registered: November 2011 Location: New Virginia, IA
Karma: 0
|
Senior Member |
|
|
I dropped my tanks pretty soon after I got my coach. It leaked out a line on top when the PO filled the tanks for my test drive. I built these ramps http://www.gmcmhphotos.com/photos/wood-ramp-construction/p5006.html
They are long and heavy, and I used treated wood, making them heavier yet. But short of a pit/lift, I think they put things at about the perfect height for laying on your back and working. Too high is a strain, makes for too far to steady the drop, and gets you in the position for more stuff to fall in your face. I love the rams, and they give me plenty of room to do what I've needed under there. I do most of my work outside on the concrete pad in front of my garage.
The tanks came out pretty easy with some vice grips and electric impact wrench, couple pieces of plywood and a floor jack. I pumped out all I could, and it was a handful but I got them off and on myself; I need more friends who have my same work schedule.
Galen Briggs
New Virginia, Iowa
1978 Palm Beach
|
|
|
Re: [GMCnet] Dropping the fuel tanks and replacing rubber fuel lines on the Barn Queen [message #228984 is a reply to message #228979] |
Fri, 08 November 2013 20:07 |
Robin Hood
Messages: 1078 Registered: April 2011
Karma: 3
|
Senior Member |
|
|
Rob "Safety Officer" Mueller persuaded me off-list to just go with the 8
jackstands I've already got instead of building expensive and heavy ramps
that will be hard to store. :)
On Fri, Nov 8, 2013 at 7:40 PM, Galen Briggs <gpbriggs@iowatelecom.net>wrote:
>
>
> I dropped my tanks pretty soon after I got my coach. It leaked out a line
> on top when the PO filled the tanks for my test drive. I built these ramps
> http://www.gmcmhphotos.com/photos/wood-ramp-construction/p5006.html
>
> They are long and heavy, and I used treated wood, making them heavier yet.
> But short of a pit/lift, I think they put things at about the perfect
> height for laying on your back and working. Too high is a strain, makes for
> too far to steady the drop, and gets you in the position for more stuff to
> fall in your face. I love the rams, and they give me plenty of room to do
> what I've needed under there. I do most of my work outside on the concrete
> pad in front of my garage.
>
> The tanks came out pretty easy with some vice grips and electric impact
> wrench, couple pieces of plywood and a floor jack. I pumped out all I
> could, and it was a handful but I got them off and on myself; I need more
> friends who have my same work schedule.
> --
> Galen Briggs
> New Virginia, Iowa
> 1978 Palm Beach
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
--
Robin Hood
Jackson, MS
2013 Subaru Outback "Top Flight"
1968 Pontiac Catalina "The Cheshire Cat"
1978 GMC Royale motorhome "Pinto Bean"
1977 GMC Palm Beach motorhome "Barn Queen"
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
|
|
|
|
|
|
|
|
Re: [GMCnet] Dropping the fuel tanks and replacing rubber fuel lines on the Barn Queen [message #229023 is a reply to message #228936] |
Sat, 09 November 2013 07:39 |
Jp Benson
Messages: 649 Registered: October 2011 Location: Fla
Karma: 2
|
Senior Member |
|
|
I used this lift to remove my tanks.
http://www.harborfreight.com/1500-lb-capacity-atvmotorcycle-lift-60536.html
It requires enough clearance to slide under the coach with the handle
removed. Is good for removing bogies too.
JP
On 11/8/2013 2:31 PM, Robin Hood wrote:
> 20 years sitting in a barn. I do not want to, but I feel that I must do
> this. The rubber lines are sure to be dry rotted, and there's a good chance
> that the tanks may be full of rust or something.
>
> The tanks need to be inspected, yes? And I must drop them to do this, yes?
> And I need to drop them in order to replace all the rubber anyway, yes?
>
> I think I will buy some 2x12s and build a ramp that will put the bottom of
> the tires a foot and a half off the ground. That will give me enough room
> to get underneath and do things.
>
> I will be doing this in the driveway of my house. The weather is pleasant
> enough, there are no wasps, and it's convenient. I might ougt to "strike
> while the iron is hot" as they say, especially since my dear sweet wife is
> so enthusiastic.
>
> Comments or suggestions? I believe the tank dropping procedure is in X7725
> somewhere? It wasn' tin the main manual that I downloaded, I need to go
> find it. I would love to hear some been-there-done-thats from those that
> have done this before already. Comments, suggestions, attaboys etc are all
> welcome. There will be video.
>
> Hoses will be replaced with corn-proof hose.
>
>
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
Goto Forum:
Current Time: Fri Oct 04 08:23:46 CDT 2024
Total time taken to generate the page: 0.01459 seconds
|