GMCforum: GMCnet » [GMCnet] One Last Governor Question

Home » Public Forums » GMCnet » [GMCnet] One Last Governor Question

Show: Today's Messages :: Polls :: Message Navigator

[GMCnet] One Last Governor Question [message #227036]

Fri, 25 October 2013 18:17

Gary Berry

Messages: 1002
Registered: May 2005

Karma: -1

Senior Member

Is the transmission governor O-ring suppose to fit down inside the
hole that the governor goes in?

--
Gary and Diana Berry
73 CL Stretch in Wa.
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

Report message to a moderator

Re: [GMCnet] One Last Governor Question [message #227040 is a reply to message #227036]

Fri, 25 October 2013 19:04

wally

Messages: 643
Registered: August 2004
Location: Omaha Nebraska

Karma: 5

Senior Member

Yes it does go inside.

Gary Berry wrote on Fri, 25 October 2013 18:17

Wally Anderson
Omaha NE
75 Glenbrook

Report message to a moderator

Re: [GMCnet] One Last Governor Question [message #227043 is a reply to message #227040]

Fri, 25 October 2013 19:07

Gary Berry

Messages: 1002
Registered: May 2005

Karma: -1

Senior Member

Hey Wally;

Thanks for the info. That's what I'll do.
--
Gary and Diana Berry
73 CL Stretch in Wa.
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

Report message to a moderator

Re: [GMCnet] One Last Governor Question [message #227053 is a reply to message #227040]

Fri, 25 October 2013 19:54

wally

Messages: 643
Registered: August 2004
Location: Omaha Nebraska

Karma: 5

Senior Member

Gary let me rephrase, the ring goes over the tube on the bottom of the governor can and then inside the trans when installing. I dunno how it would work if the ring was in the trans first, at least that's what works for me

wally wrote on Fri, 25 October 2013 19:04

Yes it does go inside.

Gary Berry wrote on Fri, 25 October 2013 18:17

Wally Anderson
Omaha NE
75 Glenbrook

Report message to a moderator

Re: [GMCnet] One Last Governor Question [message #227056 is a reply to message #227053]

Fri, 25 October 2013 20:10

USAussie

Messages: 15912
Registered: July 2007
Location: Sydney, Australia

Karma: 6

Senior Member

Gary,

This is why I suggested you take the governor with the old O-ring installed to a hardware store that had a selection of O-rings. You
could pick several that all stuck out a bit more than the old O-ring to varying degrees.

Regards,
Rob M.

-----Original Message-----
From: Wally Anderson

Gary let me rephrase, the ring goes over the tube on the bottom of the governor can and then inside the trans when installing. I
dunno how it would work if the ring was in the trans first, at least that's what works for me.

Wally

_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

Regards, Rob M. (USAussie) The Pedantic Mechanic Sydney, Australia '75 Avion - AUS - The Blue Streak TZE365V100428 '75 Avion - USA - Double Trouble TZE365V100426

Report message to a moderator

Re: [GMCnet] One Last Governor Question [message #227057 is a reply to message #227056]

Fri, 25 October 2013 20:07

Emery Stora

Messages: 959
Registered: January 2011

Karma: 4

Senior Member

Rob

I tried to uses o ring a few years back. We tried several including some a bit oversize. But they all leaked.

Emery.Stora

On Nov 25, 2013, at 7:05 PM, Rob Mueller <robmueller@iinet.net.au> wrote:

> Gary,
>
> This is why I suggested you take the governor with the old O-ring installed to a hardware store that had a selection of O-rings. You
> could pick several that all stuck out a bit more than the old O-ring to varying degrees.
>
> Regards,
> Rob M.
>
>
> -----Original Message-----
> From: Wally Anderson
>
> Gary let me rephrase, the ring goes over the tube on the bottom of the governor can and then inside the trans when installing. I
> dunno how it would work if the ring was in the trans first, at least that's what works for me.
>
> Wally
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

Report message to a moderator

Re: [GMCnet] One Last Governor Question [message #227089 is a reply to message #227057]

Sat, 26 October 2013 08:15

USAussie

Messages: 15912
Registered: July 2007
Location: Sydney, Australia

Karma: 6

Senior Member

Emery,

This is interesting as the Parts Book 78Z shows an O-ring seal on the governor shaft. Maybe it's a quad ring?

Regards,
Rob M.
The Pedantic Mechanic
USAussie - Downunder
USA '75 Avion - Double Trouble TZE365V100426
AUS '75 Avion - The Blue Streak TZE365V100428

-----Original Message-----
From: Emery Stora

Rob

I tried to uses o ring a few years back. We tried several including some a bit oversize. But they all leaked.

Emery.Stora

_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

Regards, Rob M. (USAussie) The Pedantic Mechanic Sydney, Australia '75 Avion - AUS - The Blue Streak TZE365V100428 '75 Avion - USA - Double Trouble TZE365V100426

Report message to a moderator

Previous Topic:	Dash Gauge glass replacement
Next Topic:	Anyone every tried to mate something like this to the Onan?

Goto Forum:

-=] Back to Top [=-

Current Time: Sat Oct 05 23:08:10 CDT 2024

Total time taken to generate the page: 0.00720 seconds