Home » Public Forums » GMCnet » [GMCnet] window latch fasteners
|
|
Re: [GMCnet] window latch fasteners [message #185669 is a reply to message #185661] |
Tue, 25 September 2012 20:54 |
Bruce Hart
Messages: 1501 Registered: October 2011 Location: La Grange, Wyoming
Karma: 5
|
Senior Member |
|
|
Sean,
I used rivet nuts (lso known as well nuts and well-nut threaded
inserts),and #6 flat head stainless screws.
http://www.mcmaster.com/#standard-rivet-nuts/=jgarhl
first item
http://www.mcmaster.com/#flat-head-machine-screws/=jgatmx
6-32x1/2"
It is a very tight fit for the rubber rivet nut to go through the hole in
the window.
The way that I did it was to moisten the cylinder part of the nut place a
6-32x2"
through the window hole from the outside, thread the 6-32 screw into
cylinder
part of nut and use a pry bar or claw hammer and pull on head of screw
until the
larger diameter of nut is resting against the inside of the window. This
allows for
a cushion between the window and latch.
Tom,
Sean's is a 1973 so his window latches are the same as the toll windows.
On Tue, Sep 25, 2012 at 7:17 PM, Thomas Mike <mthomas@wideopenwest.com>wrote:
>
>
> The one's your are looking at on Jim's site are for the toll windows. Not
> what you need.
> --
> Mike Thomas
> Troy, MI
> 77 ex Palm Beach, 77 Purple ex Palm Beach, 77 Royale (rear bath)
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
--
Bruce Hart
1976 Palm Beach
Milliken, Co
GMC=Got More Class
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Bruce Hart
1976 Palm Beach
1977 28' Kingsley
La Grange, Wyoming
|
|
|
Re: [GMCnet] window latch fasteners [message #185670 is a reply to message #185669] |
Tue, 25 September 2012 20:57 |
Sean
Messages: 189 Registered: March 2012
Karma: 0
|
Senior Member |
|
|
Thanks, Bruce! Exactly the type of suggestion I was hoping for :-)
On Sep 25, 2012 7:55 PM, "Bruce Hart" <hartsgmc@gmail.com> wrote:
> Sean,
> I used rivet nuts (lso known as well nuts and well-nut threaded
> inserts),and #6 flat head stainless screws.
>
> http://www.mcmaster.com/#standard-rivet-nuts/=jgarhl
> first item
> http://www.mcmaster.com/#flat-head-machine-screws/=jgatmx
> 6-32x1/2"
>
> It is a very tight fit for the rubber rivet nut to go through the hole in
> the window.
> The way that I did it was to moisten the cylinder part of the nut place a
> 6-32x2"
> through the window hole from the outside, thread the 6-32 screw into
> cylinder
> part of nut and use a pry bar or claw hammer and pull on head of screw
> until the
> larger diameter of nut is resting against the inside of the window. This
> allows for
> a cushion between the window and latch.
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
> Tom,
> Sean's is a 1973 so his window latches are the same as the toll windows.
>
> On Tue, Sep 25, 2012 at 7:17 PM, Thomas Mike <mthomas@wideopenwest.com
> >wrote:
>
> >
> >
> > The one's your are looking at on Jim's site are for the toll windows. Not
> > what you need.
> > --
> > Mike Thomas
> > Troy, MI
> > 77 ex Palm Beach, 77 Purple ex Palm Beach, 77 Royale (rear bath)
> > _______________________________________________
> > GMCnet mailing list
> > Unsubscribe or Change List Options:
> > http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
> >
>
>
>
> --
> Bruce Hart
> 1976 Palm Beach
> Milliken, Co
> GMC=Got More Class
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
--
Sean
1973 260 Painted Desert
Luna County, NM
|
|
|
|
|
Re: [GMCnet] window latch fasteners [message #185680 is a reply to message #185675] |
Tue, 25 September 2012 21:36 |
Dennis S
Messages: 3046 Registered: November 2005
Karma: 2
|
Senior Member |
|
|
[quote title
Sean,
Not sure what has failed on your current latches -- but JimK also sells just the screws for mounting to the glass. They are a plastic that will not deteriorate with sunlight exposure.
http://www.appliedgmc.com/prod.itml/icOid/797
Not sure how many you get for $8 --
The rare piece for the 73 windows is the piece that mounts to the fixed frame.
Good luck,
Dennis[/quote]
Sean,
Looks like I misread your original message -- anyway -- when I bought the screws they were about $1.25 each -- not TOOO bad a price.
Dennis
Dennis S
73 Painted Desert 230
Memphis TN Metro
|
|
|
Re: [GMCnet] window latch fasteners [message #185697 is a reply to message #185652] |
Tue, 25 September 2012 23:58 |
|
mike miller
Messages: 3576 Registered: February 2004 Location: Hillsboro, Oregon
Karma: 0
|
Senior Member |
|
|
Sean wrote on Tue, 25 September 2012 16:22 | I need to replace all the fasteners on my window latches (6 sliding
windows, 12 fasteners total).
Applied GMC sells them
(http://www.appliedgmc.com/prod.itml/icOid/797), but $8 each seems a
bit high to me.
Can anyone recommend a less-expensive source for these fasteners? I'm
open to creative suggestions
|
I have bought these from Jim Bounds and do not remember them being THAT expensive. They are metal with a small plastic sleeve to protect the glass.
While following the directions (given at the time) for the felt replacement, I broke one. I replaced it with "sex nuts" from the local Ace hardware. I understand they have several names, but only one that I remember....
They look like his: <http://www.boltdepot.com/Sex_bolts_and_Mating_screws.aspx>
I have also seen them used to connect loose leaf paper into a booklet... Binder posts(?) You might find them at an office supply place... I haven't
Anyway, I suspect they are cheaper than $8 each, but I seem to remember I paid more at Ace than I did from JimB. (Plus JimB had the little plastic sleeves.)
I would call JimB... first, then maybe stop by Ace hardware if you are not happy with Jim's answer.
Mike Miller -- Hillsboro, OR -- on the Black list
(#2)`78 23' Birchaven Rear Bath -- (#3)`77 23' Birchaven Side Bath
More Sidekicks than GMC's and a late model Malibu called 'Boo'
http://m000035.blogspot.com
|
|
|
Re: [GMCnet] window latch fasteners [message #185703 is a reply to message #185669] |
Wed, 26 September 2012 07:24 |
Sean
Messages: 189 Registered: March 2012
Karma: 0
|
Senior Member |
|
|
On Tue, Sep 25, 2012 at 7:54 PM, Bruce Hart <hartsgmc@gmail.com> wrote:
> Sean,
> I used rivet nuts (lso known as well nuts and well-nut threaded
> inserts),and #6 flat head stainless screws.
>
> http://www.mcmaster.com/#standard-rivet-nuts/=jgarhl
> first item
> http://www.mcmaster.com/#flat-head-machine-screws/=jgatmx
> 6-32x1/2"
Regarding the first item, were you referring to the
"Screwdriver-Installed Rubber-Insulated Rivet Nuts"? Should I be
looking at the first item at
http://www.mcmaster.com/#standard-rivet-nuts/=jgj1ug ?
Thanks again,
--
Sean
1973 260 Painted Desert
Luna County, NM
Gallery: http://goo.gl/Gfcpd
GMCMH Search Engine: http://goo.gl/xd8PK
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
--
Sean
1973 260 Painted Desert
Luna County, NM
|
|
|
Re: [GMCnet] window latch fasteners [message #185704 is a reply to message #185697] |
Wed, 26 September 2012 07:26 |
Sean
Messages: 189 Registered: March 2012
Karma: 0
|
Senior Member |
|
|
On Tue, Sep 25, 2012 at 10:58 PM, Mike Miller <m000035@gmail.com> wrote:
>
>
> Sean wrote on Tue, 25 September 2012 16:22
>> I need to replace all the fasteners on my window latches (6 sliding
>> windows, 12 fasteners total).
>>
>> Applied GMC sells them
>> (http://www.appliedgmc.com/prod.itml/icOid/797), but $8 each seems a
>> bit high to me.
>>
>> Can anyone recommend a less-expensive source for these fasteners? I'm
>> open to creative suggestions :)
>
>
> I have bought these from Jim Bounds and do not remember them being THAT expensive. They are metal with a small plastic sleeve to protect the glass.
>
> While following the directions (given at the time) for the felt replacement, I broke one. I replaced it with "sex nuts" from the local Ace hardware. I understand they have several names, but only one that I remember.... :twisted:
>
> They look like his: <http://www.boltdepot.com/Sex_bolts_and_Mating_screws.aspx>
>
> I have also seen them used to connect loose leaf paper into a booklet... Binder posts(?) You might find them at an office supply place... I haven't
>
> Anyway, I suspect they are cheaper than $8 each, but I seem to remember I paid more at Ace than I did from JimB. (Plus JimB had the little plastic sleeves.)
>
> I would call JimB... first, then maybe stop by Ace hardware if you are not happy with Jim's answer.
Thanks for the suggestions, Mike! I'll give Jim a call.
--
Sean
1973 260 Painted Desert
Luna County, NM
Gallery: http://goo.gl/Gfcpd
GMCMH Search Engine: http://goo.gl/xd8PK
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
--
Sean
1973 260 Painted Desert
Luna County, NM
|
|
|
Re: [GMCnet] window latch fasteners [message #185728 is a reply to message #185703] |
Wed, 26 September 2012 15:29 |
Bruce Hart
Messages: 1501 Registered: October 2011 Location: La Grange, Wyoming
Karma: 5
|
Senior Member |
|
|
Sean,
Yes the rubber insulated rivet nuts.
On Wed, Sep 26, 2012 at 6:24 AM, Sean F <wsfulmer@gmail.com> wrote:
> On Tue, Sep 25, 2012 at 7:54 PM, Bruce Hart <hartsgmc@gmail.com> wrote:
> > Sean,
> > I used rivet nuts (lso known as well nuts and well-nut threaded
> > inserts),and #6 flat head stainless screws.
> >
> > http://www.mcmaster.com/#standard-rivet-nuts/=jgarhl
> > first item
> > http://www.mcmaster.com/#flat-head-machine-screws/=jgatmx
> > 6-32x1/2"
>
>
> Regarding the first item, were you referring to the
> "Screwdriver-Installed Rubber-Insulated Rivet Nuts"? Should I be
> looking at the first item at
> http://www.mcmaster.com/#standard-rivet-nuts/=jgj1ug ?
>
> Thanks again,
>
> --
> Sean
> 1973 260 Painted Desert
> Luna County, NM
> Gallery: http://goo.gl/Gfcpd
> GMCMH Search Engine: http://goo.gl/xd8PK
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
--
Bruce Hart
1976 Palm Beach
Milliken, Co
GMC=Got More Class
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Bruce Hart
1976 Palm Beach
1977 28' Kingsley
La Grange, Wyoming
|
|
|
Goto Forum:
Current Time: Fri Sep 27 02:23:12 CDT 2024
Total time taken to generate the page: 0.01304 seconds
|