Home » Public Forums » GMCnet » [GMCnet] Mobile 1 and CV joints ?
| [GMCnet] Mobile 1 and CV joints ? [message #170993] |
Sun, 27 May 2012 18:11  |
Kingsley Coach
Messages: 2691
Registered: March 2009
Location: Nova Scotia Canada
Karma: -34
|
Senior Member |
|
|
Netters
Is Mobile 1 still an acceptable grease for CV joints or has it fallen out
of fashion?
I hope the answer is 'yes' because I just stuffed the CV joints in my
Porsche with the stuff, however, it's a easy job to do and I can replace it
with something else if necessary. As mentioned by a few in the past, the
bottom of the can had some 'cherry juice' floating around.
Tks
Mike in NS
--
Michael Beaton
1977 Kingsley 26-11
1977 Eleganza II 26-3
Antigonish, NS
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
|
|
| Re: [GMCnet] Mobile 1 and CV joints ? [message #171018 is a reply to message #170993] |
Sun, 27 May 2012 20:35  |
C Boyd
Messages: 2629
Registered: April 2006
Karma: 18
|
Senior Member |
|
|
Hi Mike: it probably will be fine in one of them Porches, but I would not use it in the Panhead.
| Kingsley Coach wrote on Sun, 27 May 2012 19:11 |
Netters
Is Mobile 1 still an acceptable grease for CV joints or has it fallen out
of fashion?
I hope the answer is 'yes' because I just stuffed the CV joints in my
Porsche with the stuff, however, it's a easy job to do and I can replace it
with something else if necessary. As mentioned by a few in the past, the
bottom of the can had some 'cherry juice' floating around.
Tks
Mike in NS
--
Michael Beaton
1977 Kingsley 26-11
1977 Eleganza II 26-3
Antigonish, NS
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
C. Boyd
76 Crestmont
East Tennessee
|
|
|
|
| Re: [GMCnet] Mobile 1 and CV joints ? [message #171050 is a reply to message #171018] |
Mon, 28 May 2012 06:55 |
Kingsley Coach
Messages: 2691
Registered: March 2009
Location: Nova Scotia Canada
Karma: -34
|
Senior Member |
|
|
Rob
No question there's a lot if reading there, but after 30 years teaching
English, I now just look at the pictures now. I will do all furture
selecting based upon colour and design of the packaging. Even this method
give a lot of selection and good quality <VBG> Thanks for the info !
Mike...a bit North of you.
On Sun, May 27, 2012 at 10:35 PM, Charles Boyd <covered-wagon@comcast.net>wrote:
>
>
> Hi Mike: it probably will be fine in one of them Porches, but I would not
> use it in the Panhead.
>
>
>
>
> Kingsley Coach wrote on Sun, 27 May 2012 19:11
> > Netters
> >
> > Is Mobile 1 still an acceptable grease for CV joints or has it fallen out
> > of fashion?
> > I hope the answer is 'yes' because I just stuffed the CV joints in my
> > Porsche with the stuff, however, it's a easy job to do and I can replace
> it
> > with something else if necessary. As mentioned by a few in the past, the
> > bottom of the can had some 'cherry juice' floating around.
> >
> > Tks
> > Mike in NS
> >
> > --
> > Michael Beaton
> > 1977 Kingsley 26-11
> > 1977 Eleganza II 26-3
> > Antigonish, NS
> > _______________________________________________
> > GMCnet mailing list
> > Unsubscribe or Change List Options:
> > http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
>
> --
> C. Boyd
> 76 Crestmont by Midas
> East Tennessee
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
--
Michael Beaton
1977 Kingsley 26-11
1977 Eleganza II 26-3
Antigonish, NS
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
| Re: [GMCnet] Mobile 1 and CV joints ? [message #171052 is a reply to message #171018] |
Mon, 28 May 2012 07:03 |
Kingsley Coach
Messages: 2691
Registered: March 2009
Location: Nova Scotia Canada
Karma: -34
|
Senior Member |
|
|
Chuck
Don't think I'd use it on the Panhead either.....the Pan is way too
complicated. The manual states on p.13, " If winter weather becomes so
extremely cold that 'Light' oil congeals in tank, add just enough kerosene
to keep oil fluid."
No measurements, no further directions...common sense required.....and that
usually leaves me out! <VBG>
Mike
On Sun, May 27, 2012 at 10:35 PM, Charles Boyd <covered-wagon@comcast.net>wrote:
>
>
> Hi Mike: it probably will be fine in one of them Porches, but I would not
> use it in the Panhead.
>
>
>
>
> Kingsley Coach wrote on Sun, 27 May 2012 19:11
> > Netters
> >
> > Is Mobile 1 still an acceptable grease for CV joints or has it fallen out
> > of fashion?
> > I hope the answer is 'yes' because I just stuffed the CV joints in my
> > Porsche with the stuff, however, it's a easy job to do and I can replace
> it
> > with something else if necessary. As mentioned by a few in the past, the
> > bottom of the can had some 'cherry juice' floating around.
> >
> > Tks
> > Mike in NS
> >
> > --
> > Michael Beaton
> > 1977 Kingsley 26-11
> > 1977 Eleganza II 26-3
> > Antigonish, NS
> > _______________________________________________
> > GMCnet mailing list
> > Unsubscribe or Change List Options:
> > http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
>
> --
> C. Boyd
> 76 Crestmont by Midas
> East Tennessee
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
--
Michael Beaton
1977 Kingsley 26-11
1977 Eleganza II 26-3
Antigonish, NS
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
| Re: [GMCnet] Mobile 1 and CV joints ? [message #171053 is a reply to message #171018] |
Mon, 28 May 2012 07:11 |
Kingsley Coach
Messages: 2691
Registered: March 2009
Location: Nova Scotia Canada
Karma: -34
|
Senior Member |
|
|
Chuck
I thought I just typed a reply, but I guess it didn't go through.
Don't know that I'd use it on my Pan either, it's way too complicated.
Page 13 of the manual states, " If winter weather becomes so extremely cold
that 'light' oil congeals in tank, add just enough kerosene to keep oil
fluid."
No ,measurements, no further instructions, just common sense required...and
most times that leaves me out! <VBG>
Mike
On Sun, May 27, 2012 at 10:35 PM, Charles Boyd <covered-wagon@comcast.net>wrote:
>
>
> Hi Mike: it probably will be fine in one of them Porches, but I would not
> use it in the Panhead.
>
>
>
>
> Kingsley Coach wrote on Sun, 27 May 2012 19:11
> > Netters
> >
> > Is Mobile 1 still an acceptable grease for CV joints or has it fallen out
> > of fashion?
> > I hope the answer is 'yes' because I just stuffed the CV joints in my
> > Porsche with the stuff, however, it's a easy job to do and I can replace
> it
> > with something else if necessary. As mentioned by a few in the past, the
> > bottom of the can had some 'cherry juice' floating around.
> >
> > Tks
> > Mike in NS
> >
> > --
> > Michael Beaton
> > 1977 Kingsley 26-11
> > 1977 Eleganza II 26-3
> > Antigonish, NS
> > _______________________________________________
> > GMCnet mailing list
> > Unsubscribe or Change List Options:
> > http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
>
> --
> C. Boyd
> 76 Crestmont by Midas
> East Tennessee
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
--
Michael Beaton
1977 Kingsley 26-11
1977 Eleganza II 26-3
Antigonish, NS
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
| Re: [GMCnet] Mobile 1 and CV joints ? [message #171054 is a reply to message #171053] |
Mon, 28 May 2012 07:30 |
k2gkk
Messages: 4452
Registered: November 2009
Karma: -8
|
Senior Member |
|
|
Isn't that Mobil One Synpower grease that is recommended for
a bunch of applications for our coaches? NOT Mobil One oil!
~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~
~~ ~ D C "Mac" Macdonald ~ ~~
~ ~ Amateur Radio - K2GKK ~ ~
~ ~ USAF and FAA, Retired ~ ~
~ ~ ~ Oklahoma City, OK ~ ~ ~
~~ ~ ~ "The Money Pit" ~ ~ ~~
~ ~ ~ '76 ex-Palm Beach ~ ~ ~
~ www.gmcmhphotos.com/okclb ~
~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~
______________
*[ ]~~~[][ ][|\
*--OO--[]---O-*
> Date: Mon, 28 May 2012 09:11:23 -0300
> From: kingsleygmc@gmail.com
> To: gmclist@temp.gmcnet.org
> Subject: Re: [GMCnet] Mobile 1 and CV joints ?
>
> Chuck
>
> I thought I just typed a reply, but I guess it didn't go through.
> Don't know that I'd use it on my Pan either, it's way too complicated.
> Page 13 of the manual states, " If winter weather becomes so extremely cold
> that 'light' oil congeals in tank, add just enough kerosene to keep oil
> fluid."
> No ,measurements, no further instructions, just common sense required...and
> most times that leaves me out! <VBG>
>
> Mike
>
> On Sun, May 27, 2012 at 10:35 PM, Charles Boyd <covered-wagon@comcast.net>wrote:
>
> >
> >
> > Hi Mike: it probably will be fine in one of them Porches, but I would not
> > use it in the Panhead.
> >
> >
> >
> >
> > Kingsley Coach wrote on Sun, 27 May 2012 19:11
> > > Netters
> > >
> > > Is Mobile 1 still an acceptable grease for CV joints or has it fallen out
> > > of fashion?
> > > I hope the answer is 'yes' because I just stuffed the CV joints in my
> > > Porsche with the stuff, however, it's a easy job to do and I can replace
> > it
> > > with something else if necessary. As mentioned by a few in the past, the
> > > bottom of the can had some 'cherry juice' floating around.
> > >
> > > Tks
> > > Mike in NS
> > >
> > > --
> > > Michael Beaton
> > > 1977 Kingsley 26-11
> > > 1977 Eleganza II 26-3
> > > Antigonish, NS
> > > _______________________________________________
> > >
> >
> > --
> > C. Boyd
> > 76 Crestmont by Midas
> > East Tennessee
>
> --
> Michael Beaton
> 1977 Kingsley 26-11
> 1977 Eleganza II 26-3
> Antigonish, NS
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
| Re: [GMCnet] Mobile 1 and CV joints ? [message #171056 is a reply to message #171054] |
Mon, 28 May 2012 08:39 |
Kingsley Coach
Messages: 2691
Registered: March 2009
Location: Nova Scotia Canada
Karma: -34
|
Senior Member |
|
|
Mac
Mobile 1 grease was the question, Not mobile 1 oil...
On Mon, May 28, 2012 at 9:30 AM, D C *Mac* Macdonald <k2gkk@hotmail.com>wrote:
>
> Isn't that Mobil One Synpower grease that is recommended for
> a bunch of applications for our coaches? NOT Mobil One oil!
>
> ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~
> ~~ ~ D C "Mac" Macdonald ~ ~~
> ~ ~ Amateur Radio - K2GKK ~ ~
> ~ ~ USAF and FAA, Retired ~ ~
> ~ ~ ~ Oklahoma City, OK ~ ~ ~
> ~~ ~ ~ "The Money Pit" ~ ~ ~~
> ~ ~ ~ '76 ex-Palm Beach ~ ~ ~
> ~ www.gmcmhphotos.com/okclb ~
> ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~
> ______________
> *[ ]~~~[][ ][|\
> *--OO--[]---O-*
>
>
>
>
> > Date: Mon, 28 May 2012 09:11:23 -0300
> > From: kingsleygmc@gmail.com
> > To: gmclist@temp.gmcnet.org
> > Subject: Re: [GMCnet] Mobile 1 and CV joints ?
> >
> > Chuck
> >
> > I thought I just typed a reply, but I guess it didn't go through.
> > Don't know that I'd use it on my Pan either, it's way too complicated.
> > Page 13 of the manual states, " If winter weather becomes so extremely
> cold
> > that 'light' oil congeals in tank, add just enough kerosene to keep oil
> > fluid."
> > No ,measurements, no further instructions, just common sense
> required...and
> > most times that leaves me out! <VBG>
> >
> > Mike
> >
> > On Sun, May 27, 2012 at 10:35 PM, Charles Boyd <
> covered-wagon@comcast.net>wrote:
> >
> > >
> > >
> > > Hi Mike: it probably will be fine in one of them Porches, but I would
> not
> > > use it in the Panhead.
> > >
> > >
> > >
> > >
> > > Kingsley Coach wrote on Sun, 27 May 2012 19:11
> > > > Netters
> > > >
> > > > Is Mobile 1 still an acceptable grease for CV joints or has it
> fallen out
> > > > of fashion?
> > > > I hope the answer is 'yes' because I just stuffed the CV joints in my
> > > > Porsche with the stuff, however, it's a easy job to do and I can
> replace
> > > it
> > > > with something else if necessary. As mentioned by a few in the past,
> the
> > > > bottom of the can had some 'cherry juice' floating around.
> > > >
> > > > Tks
> > > > Mike in NS
> > > >
> > > > --
> > > > Michael Beaton
> > > > 1977 Kingsley 26-11
> > > > 1977 Eleganza II 26-3
> > > > Antigonish, NS
> > > > _______________________________________________
> > > >
> > >
> > > --
> > > C. Boyd
> > > 76 Crestmont by Midas
> > > East Tennessee
> >
> > --
> > Michael Beaton
> > 1977 Kingsley 26-11
> > 1977 Eleganza II 26-3
> > Antigonish, NS
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
--
Michael Beaton
1977 Kingsley 26-11
1977 Eleganza II 26-3
Antigonish, NS
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
| Re: [GMCnet] Mobile 1 and CV joints ? [message #171065 is a reply to message #170993] |
Mon, 28 May 2012 09:27 |
JohnL455
Messages: 4447
Registered: October 2006
Location: Woodstock, IL
Karma: 12
|
Senior Member |
|
|
I've switched to Valvoline Synpower found at NAPA. Used to like Moble One grease as you can see when clean red grease starts to come out of fittings that are on vented boot parts. However I found the phase separation issue on the red stuff when it sat. Might not be a big deal as it's the carrier settling out. But since these GMCs sit a lot I figured there would be less of that with Synpower. Also the Synpower seems to have solved 'stearing coupler ball bind' on several posts here, so that is the best "field test" I can think of. It seems a bit more substancial than the red stuff. Only one SKU now to have in the garage.
John Lebetski
Woodstock, IL
77 Eleganza II
|
|
|
|
|
|
|
|
|
|
|
|
| Re: [GMCnet] Mobile 1 and CV joints ? [message #171171 is a reply to message #170993] |
Mon, 28 May 2012 23:53 |
Ken Burton
Messages: 10030
Registered: January 2004
Location: Hebron, Indiana
Karma: 10
|
Senior Member |
|
|
Mobile one grease is good for little red pull wagons and outhouse doors.
I almost lost some rear wheel bearings to it. Luckily Blaine spotted it and we repacked ALL of my rear wheels just in time. I use Valvoline Synpower on important things like bearings and CV joints. I use TSC non-synthetic moly grease in minimum motion things like ball joints and tie rod ends.
Save the Mobil One for the outhouse. When it fails you probably will still be able to get the door open.
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
|
|
|
|
|
|
| Re: [GMCnet] Mobile 1 and CV joints ? [message #171340 is a reply to message #171056] |
Wed, 30 May 2012 10:21 |
Ray Erspamer
Messages: 1707
Registered: May 2007
Location: Milwaukee Wisconsin
Karma: -3
|
Senior Member |
|
|
All I use on my coach is caterpillar desert gold grease, quite pricey, about $14
per tube, but it's incredible stuff.
I'm not a chemical engineer so maybe someone will tell me it's crap, but in the
research I've done I think it's the way to go. JMHO.
Ray
Ray & Lisa
78 Royale "Great Lakes Eagle"
Center Kitchen TZE368V101144
Wauwatosa, Wisconsin 53226
Email: 78GMC-Royale@att.net
414-745-3188
Web Site: http://ray-lisa.page.tl/
________________________________
From: Kingsley Coach <kingsleygmc@gmail.com>
To: gmclist@temp.gmcnet.org
Sent: Mon, May 28, 2012 8:39:45 AM
Subject: Re: [GMCnet] Mobile 1 and CV joints ?
Mac
Mobile 1 grease was the question, Not mobile 1 oil...
On Mon, May 28, 2012 at 9:30 AM, D C *Mac* Macdonald <k2gkk@hotmail.com>wrote:
>
> Isn't that Mobil One Synpower grease that is recommended for
> a bunch of applications for our coaches? NOT Mobil One oil!
>
> ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~
> ~~ ~ D C "Mac" Macdonald ~ ~~
> ~ ~ Amateur Radio - K2GKK ~ ~
> ~ ~ USAF and FAA, Retired ~ ~
> ~ ~ ~ Oklahoma City, OK ~ ~ ~
> ~~ ~ ~ "The Money Pit" ~ ~ ~~
> ~ ~ ~ '76 ex-Palm Beach ~ ~ ~
> ~ www.gmcmhphotos.com/okclb ~
> ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~
> ______________
> *[ ]~~~[][ ][|\
> *--OO--[]---O-*
>
>
>
>
> > Date: Mon, 28 May 2012 09:11:23 -0300
> > From: kingsleygmc@gmail.com
> > To: gmclist@temp.gmcnet.org
> > Subject: Re: [GMCnet] Mobile 1 and CV joints ?
> >
> > Chuck
> >
> > I thought I just typed a reply, but I guess it didn't go through.
> > Don't know that I'd use it on my Pan either, it's way too complicated.
> > Page 13 of the manual states, " If winter weather becomes so extremely
> cold
> > that 'light' oil congeals in tank, add just enough kerosene to keep oil
> > fluid."
> > No ,measurements, no further instructions, just common sense
> required...and
> > most times that leaves me out! <VBG>
> >
> > Mike
> >
> > On Sun, May 27, 2012 at 10:35 PM, Charles Boyd <
> covered-wagon@comcast.net>wrote:
> >
> > >
> > >
> > > Hi Mike: it probably will be fine in one of them Porches, but I would
> not
> > > use it in the Panhead.
> > >
> > >
> > >
> > >
> > > Kingsley Coach wrote on Sun, 27 May 2012 19:11
> > > > Netters
> > > >
> > > > Is Mobile 1 still an acceptable grease for CV joints or has it
> fallen out
> > > > of fashion?
> > > > I hope the answer is 'yes' because I just stuffed the CV joints in my
> > > > Porsche with the stuff, however, it's a easy job to do and I can
> replace
> > > it
> > > > with something else if necessary. As mentioned by a few in the past,
> the
> > > > bottom of the can had some 'cherry juice' floating around.
> > > >
> > > > Tks
> > > > Mike in NS
> > > >
> > > > --
> > > > Michael Beaton
> > > > 1977 Kingsley 26-11
> > > > 1977 Eleganza II 26-3
> > > > Antigonish, NS
> > > > _______________________________________________
> > > >
> > >
> > > --
> > > C. Boyd
> > > 76 Crestmont by Midas
> > > East Tennessee
> >
> > --
> > Michael Beaton
> > 1977 Kingsley 26-11
> > 1977 Eleganza II 26-3
> > Antigonish, NS
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
--
Michael Beaton
1977 Kingsley 26-11
1977 Eleganza II 26-3
Antigonish, NS
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Ray Erspamer
78 GMC Royale Center Kitchen
403, 3.70 Final Drive
Holley Sniper Quadrajet EFI System,
Holley Hyperspark Ignition System
414-484-9431
|
|
|
|
| Re: [GMCnet] Mobile 1 and CV joints ? [message #171432 is a reply to message #171340] |
Wed, 30 May 2012 18:54 |
 |
USAussie
Messages: 15912
Registered: July 2007
Location: Sydney, Australia
Karma: 6
|
Senior Member |
|
|
Ray,
Here's the specs for Desert Gold
NLGI # 2
Ambient Range –20° to +40° C/–4° to +104° F
Operating Range –21° to +149° C/–5° to +300° F
Base Fluid Type Petroleum
Thickener Type Lithium Complex
Color Gray
% Molybdenum disulfi de 3
Worked Penetration (mm) 265-295
% Change/100,000 stroke 10 Max
Roll Stability w/H2O, % change N/A
Viscosity Index, Min N/A
Viscosity @ 100° C, cSt 22
Viscosity @ 40° C, cSt 320
4 Ball Wear (mm) Max, Typ. 0.55
4 Ball E.P. Weld Point (kg) Min. 315
Timken E.P. Test OK load (lb) Typ. 55*
Oxidation – psi drop/500 hr Max N/A
Rust Test Pass
Salt Fog Test, hours N/A
Copper Corrosion 1b
Dropping Point +260° C (+500° F)
* The values shown are typical values and should not be used as quality
control parameters to either
Here's the specs for Valvoline Synpower
Typical Properties
NLGI Grade 2
Working range of -40 to - 400 F.
Thickener Type Lithium Complex
Color and Texture Dark Gray / Buttery
ASTM Worked Penetration @ 77° F 275
ASTM Dropping Pt, °F 500 min.
ASTM D-1743 Rust Test Pass
Weld Pt., kg 315
Load Wear Index, kg 50
Vis @ 100°C (cSt) 5.9
Viscosity Index 135
Pour Point °F -80
As we say Downunder they're near as dammit! ;-)
Regards,
Rob M.
-----Original Message-----
From: gmclist-bounces@temp.gmcnet.org
[mailto:gmclist-bounces@temp.gmcnet.org] On Behalf Of Ray Erspamer
Sent: Thursday, 31 May 2012 1:22 AM
To: gmclist@temp.gmcnet.org
Subject: Re: [GMCnet] Mobile 1 and CV joints ?
All I use on my coach is caterpillar desert gold grease, quite pricey, about
$14
per tube, but it's incredible stuff.
I'm not a chemical engineer so maybe someone will tell me it's crap, but in
the
research I've done I think it's the way to go. JMHO.
Ray
Ray & Lisa
78 Royale "Great Lakes Eagle"
Center Kitchen TZE368V101144
Wauwatosa, Wisconsin 53226
Email: 78GMC-Royale@att.net
414-745-3188
Web Site: http://ray-lisa.page.tl/
________________________________
From: Kingsley Coach <kingsleygmc@gmail.com>
To: gmclist@temp.gmcnet.org
Sent: Mon, May 28, 2012 8:39:45 AM
Subject: Re: [GMCnet] Mobile 1 and CV joints ?
Mac
Mobile 1 grease was the question, Not mobile 1 oil...
On Mon, May 28, 2012 at 9:30 AM, D C *Mac* Macdonald
<k2gkk@hotmail.com>wrote:
>
> Isn't that Mobil One Synpower grease that is recommended for
> a bunch of applications for our coaches? NOT Mobil One oil!
>
> ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~
> ~~ ~ D C "Mac" Macdonald ~ ~~
> ~ ~ Amateur Radio - K2GKK ~ ~
> ~ ~ USAF and FAA, Retired ~ ~
> ~ ~ ~ Oklahoma City, OK ~ ~ ~
> ~~ ~ ~ "The Money Pit" ~ ~ ~~
> ~ ~ ~ '76 ex-Palm Beach ~ ~ ~
> ~ www.gmcmhphotos.com/okclb ~
> ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~
> ______________
> *[ ]~~~[][ ][|\
> *--OO--[]---O-*
>
>
>
>
> > Date: Mon, 28 May 2012 09:11:23 -0300
> > From: kingsleygmc@gmail.com
> > To: gmclist@temp.gmcnet.org
> > Subject: Re: [GMCnet] Mobile 1 and CV joints ?
> >
> > Chuck
> >
> > I thought I just typed a reply, but I guess it didn't go through.
> > Don't know that I'd use it on my Pan either, it's way too complicated.
> > Page 13 of the manual states, " If winter weather becomes so extremely
> cold
> > that 'light' oil congeals in tank, add just enough kerosene to keep oil
> > fluid."
> > No ,measurements, no further instructions, just common sense
> required...and
> > most times that leaves me out! <VBG>
> >
> > Mike
> >
> > On Sun, May 27, 2012 at 10:35 PM, Charles Boyd <
> covered-wagon@comcast.net>wrote:
> >
> > >
> > >
> > > Hi Mike: it probably will be fine in one of them Porches, but I would
> not
> > > use it in the Panhead.
> > >
> > >
> > >
> > >
> > > Kingsley Coach wrote on Sun, 27 May 2012 19:11
> > > > Netters
> > > >
> > > > Is Mobile 1 still an acceptable grease for CV joints or has it
> fallen out
> > > > of fashion?
> > > > I hope the answer is 'yes' because I just stuffed the CV joints in
my
> > > > Porsche with the stuff, however, it's a easy job to do and I can
> replace
> > > it
> > > > with something else if necessary. As mentioned by a few in the past,
> the
> > > > bottom of the can had some 'cherry juice' floating around.
> > > >
> > > > Tks
> > > > Mike in NS
> > > >
> > > > --
> > > > Michael Beaton
> > > > 1977 Kingsley 26-11
> > > > 1977 Eleganza II 26-3
> > > > Antigonish, NS
> > > > _______________________________________________
> > > >
> > >
> > > --
> > > C. Boyd
> > > 76 Crestmont by Midas
> > > East Tennessee
> >
> > --
> > Michael Beaton
> > 1977 Kingsley 26-11
> > 1977 Eleganza II 26-3
> > Antigonish, NS
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
--
Michael Beaton
1977 Kingsley 26-11
1977 Eleganza II 26-3
Antigonish, NS
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Regards,
Rob M. (USAussie)
The Pedantic Mechanic
Sydney, Australia
'75 Avion - AUS - The Blue Streak TZE365V100428
'75 Avion - USA - Double Trouble TZE365V100426
|
|
|
|
| Re: [GMCnet] Mobile 1 and CV joints ? [message #171545 is a reply to message #171432] |
Thu, 31 May 2012 10:48 |
Ray Erspamer
Messages: 1707
Registered: May 2007
Location: Milwaukee Wisconsin
Karma: -3
|
Senior Member |
|
|
This is great info Rob, thanks for sharing it !
Ray
Ray & Lisa
78 Royale "Great Lakes Eagle"
Center Kitchen TZE368V101144
Wauwatosa, Wisconsin 53226
Email: 78GMC-Royale@att.net
414-745-3188
Web Site: http://ray-lisa.page.tl/
________________________________
From: Robert Mueller <robmueller@iinet.net.au>
To: gmclist@temp.gmcnet.org
Sent: Wed, May 30, 2012 6:53:46 PM
Subject: Re: [GMCnet] Mobile 1 and CV joints ?
Ray,
Here's the specs for Desert Gold
NLGI # 2
Ambient Range –20° to +40° C/–4° to +104° F
Operating Range –21° to +149° C/–5° to +300° F
Base Fluid Type Petroleum
Thickener Type Lithium Complex
Color Gray
% Molybdenum disulfi de 3
Worked Penetration (mm) 265-295
% Change/100,000 stroke 10 Max
Roll Stability w/H2O, % change N/A
Viscosity Index, Min N/A
Viscosity @ 100° C, cSt 22
Viscosity @ 40° C, cSt 320
4 Ball Wear (mm) Max, Typ. 0.55
4 Ball E.P. Weld Point (kg) Min. 315
Timken E.P. Test OK load (lb) Typ. 55*
Oxidation – psi drop/500 hr Max N/A
Rust Test Pass
Salt Fog Test, hours N/A
Copper Corrosion 1b
Dropping Point +260° C (+500° F)
* The values shown are typical values and should not be used as quality
control parameters to either
Here's the specs for Valvoline Synpower
Typical Properties
NLGI Grade 2
Working range of -40 to - 400 F.
Thickener Type Lithium Complex
Color and Texture Dark Gray / Buttery
ASTM Worked Penetration @ 77° F 275
ASTM Dropping Pt, °F 500 min.
ASTM D-1743 Rust Test Pass
Weld Pt., kg 315
Load Wear Index, kg 50
Vis @ 100°C (cSt) 5.9
Viscosity Index 135
Pour Point °F -80
As we say Downunder they're near as dammit! ;-)
Regards,
Rob M.
-----Original Message-----
From: gmclist-bounces@temp.gmcnet.org
[mailto:gmclist-bounces@temp.gmcnet.org] On Behalf Of Ray Erspamer
Sent: Thursday, 31 May 2012 1:22 AM
To: gmclist@temp.gmcnet.org
Subject: Re: [GMCnet] Mobile 1 and CV joints ?
All I use on my coach is caterpillar desert gold grease, quite pricey, about
$14
per tube, but it's incredible stuff.
I'm not a chemical engineer so maybe someone will tell me it's crap, but in
the
research I've done I think it's the way to go. JMHO.
Ray
Ray & Lisa
78 Royale "Great Lakes Eagle"
Center Kitchen TZE368V101144
Wauwatosa, Wisconsin 53226
Email: 78GMC-Royale@att.net
414-745-3188
Web Site: http://ray-lisa.page.tl/
________________________________
From: Kingsley Coach <kingsleygmc@gmail.com>
To: gmclist@temp.gmcnet.org
Sent: Mon, May 28, 2012 8:39:45 AM
Subject: Re: [GMCnet] Mobile 1 and CV joints ?
Mac
Mobile 1 grease was the question, Not mobile 1 oil...
On Mon, May 28, 2012 at 9:30 AM, D C *Mac* Macdonald
<k2gkk@hotmail.com>wrote:
>
> Isn't that Mobil One Synpower grease that is recommended for
> a bunch of applications for our coaches? NOT Mobil One oil!
>
> ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~
> ~~ ~ D C "Mac" Macdonald ~ ~~
> ~ ~ Amateur Radio - K2GKK ~ ~
> ~ ~ USAF and FAA, Retired ~ ~
> ~ ~ ~ Oklahoma City, OK ~ ~ ~
> ~~ ~ ~ "The Money Pit" ~ ~ ~~
> ~ ~ ~ '76 ex-Palm Beach ~ ~ ~
> ~ www.gmcmhphotos.com/okclb ~
> ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~
> ______________
> *[ ]~~~[][ ][|\
> *--OO--[]---O-*
>
>
>
>
> > Date: Mon, 28 May 2012 09:11:23 -0300
> > From: kingsleygmc@gmail.com
> > To: gmclist@temp.gmcnet.org
> > Subject: Re: [GMCnet] Mobile 1 and CV joints ?
> >
> > Chuck
> >
> > I thought I just typed a reply, but I guess it didn't go through.
> > Don't know that I'd use it on my Pan either, it's way too complicated.
> > Page 13 of the manual states, " If winter weather becomes so extremely
> cold
> > that 'light' oil congeals in tank, add just enough kerosene to keep oil
> > fluid."
> > No ,measurements, no further instructions, just common sense
> required...and
> > most times that leaves me out! <VBG>
> >
> > Mike
> >
> > On Sun, May 27, 2012 at 10:35 PM, Charles Boyd <
> covered-wagon@comcast.net>wrote:
> >
> > >
> > >
> > > Hi Mike: it probably will be fine in one of them Porches, but I would
> not
> > > use it in the Panhead.
> > >
> > >
> > >
> > >
> > > Kingsley Coach wrote on Sun, 27 May 2012 19:11
> > > > Netters
> > > >
> > > > Is Mobile 1 still an acceptable grease for CV joints or has it
> fallen out
> > > > of fashion?
> > > > I hope the answer is 'yes' because I just stuffed the CV joints in
my
> > > > Porsche with the stuff, however, it's a easy job to do and I can
> replace
> > > it
> > > > with something else if necessary. As mentioned by a few in the past,
> the
> > > > bottom of the can had some 'cherry juice' floating around.
> > > >
> > > > Tks
> > > > Mike in NS
> > > >
> > > > --
> > > > Michael Beaton
> > > > 1977 Kingsley 26-11
> > > > 1977 Eleganza II 26-3
> > > > Antigonish, NS
> > > > _______________________________________________
> > > >
> > >
> > > --
> > > C. Boyd
> > > 76 Crestmont by Midas
> > > East Tennessee
> >
> > --
> > Michael Beaton
> > 1977 Kingsley 26-11
> > 1977 Eleganza II 26-3
> > Antigonish, NS
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
--
Michael Beaton
1977 Kingsley 26-11
1977 Eleganza II 26-3
Antigonish, NS
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Ray Erspamer
78 GMC Royale Center Kitchen
403, 3.70 Final Drive
Holley Sniper Quadrajet EFI System,
Holley Hyperspark Ignition System
414-484-9431
|
|
|
|
| Re: [GMCnet] Mobile 1 and CV joints ? [message #171556 is a reply to message #171432] |
Thu, 31 May 2012 17:40 |
Dave Mumert
Messages: 272
Registered: February 2004
Location: Olds, AB, Canada
Karma: 0
|
Senior Member |
|
|
Hi Rob
You guys hanging by your feet down there have different Desert Gold the we
do, maybe you have the specs for Ultra 5Moly.
Here is Cat Parts page Desert Gold
http://parts.cat.com/parts/machine-fluids/greases/desert-gold-grease
Cat Ultra 5Moly
http://parts.cat.com/parts/machine-fluids/greases/ultra-5moly-grease
I don't think the operating range goes to 2320 degrees I think they mean 232
degrees. At what temperature does steel melt?
I read somewhere that Calcium Sulfonate was a better thickener than Lithium
when there a chance that moisture might be present.
Like you say, it is pretty much the same as Valvoline Synpower
Dave Mumert
> -----Original Message-----
> Subject: Re: [GMCnet] Mobile 1 and CV joints ?
>
> Here's the specs for Desert Gold
>
> NLGI # 2
> Ambient Range –20° to +40° C/–4° to +104° F Operating Range –21° to +149°
> C/–5° to +300° F Base Fluid Type Petroleum Thickener Type Lithium Complex
> Color Gray % Molybdenum disulfi de 3 Worked Penetration (mm) 265-295 %
> Change/100,000 stroke 10 Max Roll Stability w/H2O, % change N/A Viscosity
> Index, Min N/A Viscosity @ 100° C, cSt 22 Viscosity @ 40° C, cSt 320
> 4 Ball Wear (mm) Max, Typ. 0.55
> 4 Ball E.P. Weld Point (kg) Min. 315
> Timken E.P. Test OK load (lb) Typ. 55*
> Oxidation – psi drop/500 hr Max N/A
> Rust Test Pass
> Salt Fog Test, hours N/A
> Copper Corrosion 1b
> Dropping Point +260° C (+500° F)
> * The values shown are typical values and should not be used as quality
> control parameters to either
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
|
| Re: [GMCnet] Mobile 1 and CV joints ? [message #171558 is a reply to message #170993] |
Thu, 31 May 2012 17:51 |
JohnL455
Messages: 4447
Registered: October 2006
Location: Woodstock, IL
Karma: 12
|
Senior Member |
|
|
Cat has so many greases I don't know which to use so I stick with valvoline Synpower. I guess if I had a Cat it would tell me which one. Mine just meow and Hissss.
John Lebetski
Woodstock, IL
77 Eleganza II
|
|
|
|
Goto Forum:
Current Time: Wed Nov 20 04:31:15 CST 2024
Total time taken to generate the page: 0.02479 seconds
|
GMCforum
Search
Help
Register
Login
Home
