GMCforum: GMCnet » Switches on Refer Cabinet

Home » Public Forums » GMCnet » Switches on Refer Cabinet

Show: Today's Messages :: Polls :: Message Navigator

Switches on Refer Cabinet [message #168942]

Tue, 08 May 2012 15:13

glacierfl

Messages: 444
Registered: June 2011

Karma: 0

Senior Member

Hello All,

Can anyone tell me what type the switches are and the ratings are of the switches on the refer cabinet?

Thanks in advance.

cheers and beers

Steve & Debbie Monticello, FL 77 Palm Beach :- Aurora EX G4WDT

Report message to a moderator

Re: Switches on Refer Cabinet [message #168960 is a reply to message #168942]

Tue, 08 May 2012 17:07

bwevers

Messages: 597
Registered: October 2010
Location: San Jose

Karma: 5

Senior Member

glacierfl,
Are you referring to the 4 switches by the door?
I bought some off of Ebay a while ago.
They look very similar, but they don't have labels.
And they fit the wall plate cut out.

I think they were rated at 125V - 16amps.

I'll check the part numbers when I get home.

Regards,
Bill

Bill Wevers GMC49ers, GMC Western States 1975 Glenbrook - Manny Powerdrive, OneTon 455 F Block, G heads San Jose

Report message to a moderator

Re: Switches on Refer Cabinet [message #168993 is a reply to message #168942]

Tue, 08 May 2012 21:19

bwevers

Messages: 597
Registered: October 2010
Location: San Jose

Karma: 5

Senior Member

Here's some information:

On my 1975 Glenbrook the 4 switches by the refer cabinet have a mounting hole of 0.83" X 1.45". The terminals are 0.25" (6 of them).

They are called rocker switches DPDT, ON-ON

See Digikey item:
http://www.digikey.com
http://spec.e-switch.com/lambweb/34-RVW4GD1100.pdf
http://media.digikey.com/Photos/E-Switch%20Photos/RVW4GD110.jpg

Digikey part number
EG4784-ND Glossy finish $3.38
EG4785-ND Mate finish $4.87

They don't have labels but they are functionally the same.

Regards,
Bill

Bill Wevers GMC49ers, GMC Western States 1975 Glenbrook - Manny Powerdrive, OneTon 455 F Block, G heads San Jose

Report message to a moderator

Re: Switches on Refer Cabinet [message #169040 is a reply to message #168942]

Wed, 09 May 2012 10:36

armandminnie

Messages: 864
Registered: May 2009
Location: Marana, AZ

Karma: 2

Senior Member

I bought new switches at a local RV supply house. They are a different form factor but I covered the old holes with a new piece of wood and made new holes. I think they look better. Total cost for 5 switches and two lights (one switch and light in bath) with mounting plates was about $40.

Photo is at:
http://www.gmcmhphotos.com/photos/misc-junk/p44223-replacement-switches.html
or http://tiny.cc/o9r1dw

Armand Minnie
Marana, AZ
'76 Eleganza II TZE166V103202
visit my gmc blog
click here to visit gmcws.org

Report message to a moderator

Previous Topic:	Not a GMC
Next Topic:	[GMCnet] test post and request

Goto Forum:

-=] Back to Top [=-

Current Time: Tue Oct 01 12:30:31 CDT 2024

Total time taken to generate the page: 0.01317 seconds