Home » Public Forums » GMCnet » powder coating
powder coating [message #157141] |
Tue, 17 January 2012 22:50 |
glacierfl
Messages: 444 Registered: June 2011
Karma: 0
|
Senior Member |
|
|
Hello,
Decided to get some GMC parts powder coated. I believe that this is very hard wearing, and resistant to chemicals etc.
I called a local powder coater, and asked how much for the metal door panel gave him the size!, he said $25, and if i had lots of stuff would be cheaper in the long run....
So the metal door panel & Alum handle, heating vents, the seat bases, the front rear mirror mount, are all off next week for coating.
Thinking of getting the OEM wheels powder coated also, until i can find a used cheap set of alum ones !!!!
Would that affect the tire pressure at all??
Any thoughts on this please.
cheers and beers
Steve & Debbie
Monticello, FL
77 Palm Beach :- Aurora
EX G4WDT
|
|
|
Re: [GMCnet] powder coating [message #157146 is a reply to message #157141] |
Tue, 17 January 2012 23:36 |
Dolph Santorine
Messages: 1236 Registered: April 2011 Location: Wheeling, WV
Karma: -41
|
Senior Member |
|
|
Powder coating is great stuff. It does exhibit some chalking from UV exposure. You can solve that by waxing it.
It's thicker than solvent based paints. Other than that, I don't see why it won't be great on wheels.
Dolph Santorine
adolph@Santorine.org
Excuse me for not being my usual wordy and sporadically verbose self. This message is sent from my iPhone.
No trees were killed in the sending of this message, but a large number of electrons were terribly inconvenienced.
On Jan 17, 2012, at 11:50 PM, steve & debbie <zzdebz@yahoo.com> wrote:
>
>
> Hello,
> Decided to get some GMC parts powder coated. I believe that this is very hard wearing, and resistant to chemicals etc.
>
> I called a local powder coater, and asked how much for the metal door panel gave him the size!, he said $25, and if i had lots of stuff would be cheaper in the long run....
>
> So the metal door panel & Alum handle, heating vents, the seat bases, the front rear mirror mount, are all off next week for coating.
>
> Thinking of getting the OEM wheels powder coated also, until i can find a used cheap set of alum ones !!!!
>
> Would that affect the tire pressure at all??
>
> Any thoughts on this please.
>
> cheers and beers
> --
> Steve & Debbie
> Monticello, FL
> 77 Palm Beach :- Aurora
> EX G4WDT
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
Re: [GMCnet] powder coating [message #157147 is a reply to message #157146] |
Tue, 17 January 2012 23:42 |
Luvn737s
Messages: 1106 Registered: June 2007
Karma: 2
|
Senior Member |
|
|
I am told that powdercoating may chip and when it does, repairs are not as easy to make as paint. I wonder if wheel weight installation and removal might cause chipping.
Randy
1973 26' Painted Desert
Ahwatukee (Phoenix) AZ
|
|
|
Re: [GMCnet] powder coating [message #157148 is a reply to message #157146] |
Wed, 18 January 2012 00:00 |
peter bailey
Messages: 367 Registered: March 2009 Location: Gawler, South Australia
Karma: 0
|
Senior Member |
|
|
Wheels need to be plated against rust prior to painting and powder coating
chips easily (if not plated corrosion will occur underneath the paint,
powder coating is pourous. wheels are better painted with 2 pack urethane it
is more flexable as well as hard.
Peter Bailey
from Ozy (Aussie)
----- Original Message -----
From: "Dolph Santorine" <dolph@dolphsantorine.com>
To: <gmclist@temp.gmcnet.org>
Sent: Wednesday, January 18, 2012 4:06 PM
Subject: Re: [GMCnet] powder coating
> Powder coating is great stuff. It does exhibit some chalking from UV
> exposure. You can solve that by waxing it.
>
> It's thicker than solvent based paints. Other than that, I don't see why
> it won't be great on wheels.
>
> Dolph Santorine
>
> adolph@Santorine.org
>
> Excuse me for not being my usual wordy and sporadically verbose self. This
> message is sent from my iPhone.
>
> No trees were killed in the sending of this message, but a large number of
> electrons were terribly inconvenienced.
>
> On Jan 17, 2012, at 11:50 PM, steve & debbie <zzdebz@yahoo.com> wrote:
>
>>
>>
>> Hello,
>> Decided to get some GMC parts powder coated. I believe that this is very
>> hard wearing, and resistant to chemicals etc.
>>
>> I called a local powder coater, and asked how much for the metal door
>> panel gave him the size!, he said $25, and if i had lots of stuff would
>> be cheaper in the long run....
>>
>> So the metal door panel & Alum handle, heating vents, the seat bases, the
>> front rear mirror mount, are all off next week for coating.
>>
>> Thinking of getting the OEM wheels powder coated also, until i can find a
>> used cheap set of alum ones !!!!
>>
>> Would that affect the tire pressure at all??
>>
>> Any thoughts on this please.
>>
>> cheers and beers
>> --
>> Steve & Debbie
>> Monticello, FL
>> 77 Palm Beach :- Aurora
>> EX G4WDT
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
>
> -----
> No virus found in this message.
> Checked by AVG - www.avg.com
> Version: 2012.0.1901 / Virus Database: 2109/4749 - Release Date: 01/17/12
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
Re: [GMCnet] powder coating [message #157149 is a reply to message #157147] |
Wed, 18 January 2012 00:14 |
glacierfl
Messages: 444 Registered: June 2011
Karma: 0
|
Senior Member |
|
|
Hello,
UV chalking :- Wonder how long that takes months, years ??.
I wonder if applying UV resistant coating from time to time would alleviate that problem??. Now you mentione that, i remembered i had seen many years ago, powder coating on some metal work that lived outside, it looked chalky, so UV did that. "You learn something new everyday." Wheel weights, could see how they might scratch the coating... Was thinking of getting the A-Arms etc done also to match. Any known effect on the ability of tires to seal correctly, with the coating applied ???. Would make the wheels look rather nice, but do not want to splash out, if its only gonna look good for a short while ???
cheers and beers
Steve & Debbie
Monticello, FL
77 Palm Beach :- Aurora
EX G4WDT
|
|
|
Re: [GMCnet] powder coating [message #157150 is a reply to message #157147] |
Wed, 18 January 2012 00:52 |
jtblank
Messages: 237 Registered: June 2007 Location: Tulare, CA
Karma: 1
|
Senior Member |
|
|
The easy way to eliminate chipping from wheel weights is to eliminate them, use balancing beads or powder. However use of the OEM hubcaps would also lead to scratching and chipping.
John Blankenship
'76 Palm Beach
Tulare, CA
|
|
|
Re: powder coating [message #157152 is a reply to message #157141] |
Wed, 18 January 2012 07:16 |
Bob de Kruyff
Messages: 4260 Registered: January 2004 Location: Chandler, AZ
Karma: 1
|
Senior Member |
|
|
glacierfl wrote on Tue, 17 January 2012 21:50 | Hello,
Decided to get some GMC parts powder coated. I believe that this is very hard wearing, and resistant to chemicals etc.
I called a local powder coater, and asked how much for the metal door panel gave him the size!, he said $25, and if i had lots of stuff would be cheaper in the long run....
So the metal door panel & Alum handle, heating vents, the seat bases, the front rear mirror mount, are all off next week for coating.
Thinking of getting the OEM wheels powder coated also, until i can find a used cheap set of alum ones !!!!
Would that affect the tire pressure at all??
Any thoughts on this please.
cheers and beers
|
We powder coat many components such as appliance dollies and have also tried wheels. It requires all of the same cautions as most other paints and although it can provide a great finish, it is not a majic solution for corrosion, chipping or fading. Many cars and trucks are powder coated as a way to meet emission requirements for the paint shops.
Bob de Kruyff
78 Eleganza
Chandler, AZ
|
|
|
Re: [GMCnet] powder coating [message #157155 is a reply to message #157141] |
Wed, 18 January 2012 07:21 |
Steven Ferguson
Messages: 3447 Registered: May 2006
Karma: 0
|
Senior Member |
|
|
Only if you powder coat the wheels and put them into the curing oven with
the tires still on them.
On Tue, Jan 17, 2012 at 9:50 PM, steve & debbie <zzdebz@yahoo.com> wrote:
>
>
> Hello,
> Decided to get some GMC parts powder coated. I believe that this is very
> hard wearing, and resistant to chemicals etc.
>
> I called a local powder coater, and asked how much for the metal door
> panel gave him the size!, he said $25, and if i had lots of stuff would be
> cheaper in the long run....
>
> So the metal door panel & Alum handle, heating vents, the seat bases, the
> front rear mirror mount, are all off next week for coating.
>
> Thinking of getting the OEM wheels powder coated also, until i can find a
> used cheap set of alum ones !!!!
>
> Would that affect the tire pressure at all??
>
> Any thoughts on this please.
>
> cheers and beers
> --
> Steve & Debbie
> Monticello, FL
> 77 Palm Beach :- Aurora
> EX G4WDT
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
--
Fathom the hypocrisy of a nation where every citizen must prove they have
health insurance......but not everyone has to prove they're a citizen.
Steve Ferguson
Sierra Vista, AZ
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
Re: [GMCnet] powder coating [message #157164 is a reply to message #157150] |
Wed, 18 January 2012 10:18 |
rssbob
Messages: 259 Registered: January 2004 Location: La Mesa, Ca. (San Diego a...
Karma: 0
|
Senior Member |
|
|
The wheels on my recently acquired Palm Beach were disgusting looking so I had them sand blasted and powder coated. I love the result but when I installed the first hub cap I could see they were going to chip and scratch the powder coated finish so I decided to go with the "non-hub-cap" look. Now I am going to clean and paint everything inside the wheel wells black, including my lug nuts. I also powder coated my old hub covers with a matching green which I think will really set it off. I will post some pictures when I get one side done. That also frees up a bunch of hub caps in case anyone needs any. I have about 10 of them in various conditions.
On Jan 17, 2012, at 10:52 PM, John Blankenship wrote:
>
>
> The easy way to eliminate chipping from wheel weights is to eliminate them, use balancing beads or powder. However use of the OEM hubcaps would also lead to scratching and chipping.
> --
> John Blankenship
> '76 Palm Beach
> Tulare, CA
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Bob Sobrito
78 Palm Beach
La Mesa, Ca
|
|
|
|
|
Re: [GMCnet] powder coating [message #157191 is a reply to message #157189] |
Wed, 18 January 2012 13:42 |
sgltrac
Messages: 2797 Registered: April 2011
Karma: 1
|
Senior Member |
|
|
Most of the powder coated parts for my rear suspension ended up that way due to the cost of sand blasting. The cost to blast the parts was 60 percent or so of the total cost to blast and powder coat. Originally I was planning to have bogie parts blasted then top coat with automotive paint but it just diddnt make sense (to me anyway) to not have the whole thing done since the powder cost was same or less than my material+labor costs.
Sully
77 royale
Sent from my Verizon Wireless BlackBerry
-----Original Message-----
From: Matt Colie <matt7323tze@gmail.com>
Sender: gmclist-bounces@temp.gmcnet.org
Date: Wed, 18 Jan 2012 13:33:20
To: <gmclist@temp.gmcnet.org>
Reply-To: gmclist@temp.gmcnet.org
Subject: Re: [GMCnet] powder coating
rssbob wrote on Wed, 18 January 2012 11:18
> The wheels on my recently acquired Palm Beach were disgusting looking so I had them sand blasted and powder coated. I love the result but when I installed the first hub cap I could see they were going to chip and scratch the powder coated finish so I decided to go with the "non-hub-cap" look. Now I am going to clean and paint everything inside the wheel wells black, including my lug nuts. I also powder coated my old hub covers with a matching green which I think will really set it off. I will post some pictures when I get one side done. That also frees up a bunch of hub caps in case anyone needs any. I have about 10 of them in various conditions.
>
> Bob Sobrito
I now of a collection of mostly ugly 16" wheels, I went around locally for quotes to sand blast and powder coat 7 and it was close to what JimK would charge for hub centered alloy. I'm still planning to sand blast at a really inexpensive shop and squirt so primer on them myself. I would have liked the powder coat.
Matt
--
Matt & Mary Colie
'73 Glacier 23 Chaumière (say show-me-air) Just about as stock as you will find
SE Michigan - Twixt A2 and Detroit
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Sully
77 Royale basket case.
Future motorhome land speed record holder(bucket list)
Seattle, Wa.
|
|
|
Re: [GMCnet] powder coating [message #157193 is a reply to message #157189] |
Wed, 18 January 2012 13:50 |
Keith V
Messages: 2337 Registered: March 2008 Location: Mounds View,MN
Karma: 0
|
Senior Member |
|
|
I am so not a fan of powder coating.
I firmly believe the industry has the public snowed.
It has a sexy new(ish) name that sounds so cool and hi tech, it must be better right??
The only real advantage of powder coating is that it's cleaner, no solvents and the over spray sweeps up.
Durability wise a good polyurethane paint is far superior.
They are both tough and temperature resistant, but urethane Is more flexible, has a chemical bond to the substrate rather than a mechanical bond, it's repairable, better UV protection, and it looks better. It's also low temperature, no need to bake the snot out of your part (like 450 degrees)
And its repairable, just spray some more on top....lets see you fix powder coating...
I own my own powder coater and do use it.
But 2 part urethane is better.
Did I mention paint is repairable??
Keith Vasilakes
Mounds View. MN
75 ex Royale GMC
ask me about MicroLevel
Cell, 763-732-3419
My427v8@hotmail.com
|
|
|
Re: [GMCnet] powder coating [message #157196 is a reply to message #157191] |
Wed, 18 January 2012 13:58 |
James Hupy
Messages: 6806 Registered: May 2010
Karma: -62
|
Senior Member |
|
|
Many of the commercial powder coaters in this area prefer to do the media
blasting in house. They have several media that they use, from silicon
carbide, aluminum oxide, glass beads, walnut shells, soda, etc. The powder
coating should be applied as soon as possible after media blasting and
metal prepping. That way they know that some grease monkey has not been
handling the parts with stuff on their hands that prevents good adhesion. I
personally have a powder coating outfit that I use for parts that are small
enough to go in a 42" electric range oven. I have one in my shop that I use
exclusively for that purpose. I also have a glass beading cabinet that uses
compressed air to blast the surfaces of parts with glass beads to remove
rust and scale. I use non residual chlorinated hydrocarbons to clean the
parts before I powder coat them. On heavy castings like GMC knuckles that
have been subjected to chassis grease, I first bake them in the oven for a
couple of hours, then let them cool off before I final clean them and
powder coat them. I have done quite a lot of it over the years, and have
learned what does and what does not work. If it is not clean enough to eat
off of, it is not clean enough to powder coat. Some lessons I have learned
the hard way.
Jim Hupy
Salem, OR
78 GMC Royale 403
On Wed, Jan 18, 2012 at 11:42 AM, <sgltrac@gmail.com> wrote:
> Most of the powder coated parts for my rear suspension ended up that way
> due to the cost of sand blasting. The cost to blast the parts was 60
> percent or so of the total cost to blast and powder coat. Originally I was
> planning to have bogie parts blasted then top coat with automotive paint
> but it just diddnt make sense (to me anyway) to not have the whole thing
> done since the powder cost was same or less than my material+labor costs.
>
> Sully
> 77 royale
> Sent from my Verizon Wireless BlackBerry
>
> -----Original Message-----
> From: Matt Colie <matt7323tze@gmail.com>
> Sender: gmclist-bounces@temp.gmcnet.org
> Date: Wed, 18 Jan 2012 13:33:20
> To: <gmclist@temp.gmcnet.org>
> Reply-To: gmclist@temp.gmcnet.org
> Subject: Re: [GMCnet] powder coating
>
>
>
> rssbob wrote on Wed, 18 January 2012 11:18
> > The wheels on my recently acquired Palm Beach were disgusting looking so
> I had them sand blasted and powder coated. I love the result but when I
> installed the first hub cap I could see they were going to chip and scratch
> the powder coated finish so I decided to go with the "non-hub-cap" look.
> Now I am going to clean and paint everything inside the wheel wells black,
> including my lug nuts. I also powder coated my old hub covers with a
> matching green which I think will really set it off. I will post some
> pictures when I get one side done. That also frees up a bunch of hub caps
> in case anyone needs any. I have about 10 of them in various conditions.
> >
> > Bob Sobrito
>
> I now of a collection of mostly ugly 16" wheels, I went around locally for
> quotes to sand blast and powder coat 7 and it was close to what JimK would
> charge for hub centered alloy. I'm still planning to sand blast at a
> really inexpensive shop and squirt so primer on them myself. I would have
> liked the powder coat.
>
> Matt
> --
> Matt & Mary Colie
> '73 Glacier 23 Chaumière (say show-me-air) Just about as stock as you will
> find
> SE Michigan - Twixt A2 and Detroit
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
Re: [GMCnet] powder coating [message #157200 is a reply to message #157196] |
Wed, 18 January 2012 14:14 |
James Hupy
Messages: 6806 Registered: May 2010
Karma: -62
|
Senior Member |
|
|
And as an addendum to this posting, I agree with Keith, on some things, 2
part catalyzed urethane paints are an incredibly durable coating properly
applied. And they can be touched up easily. Either method is very durable
when proper steps are used in their application. Powder coat has the
advantage of being able to be handled as soon as the parts are cool enough
to do so. Urethanes are soft until all the solvents find their way out, (or
the catalyzing process is complete). Just what I have found. Your
experiences may vary. But, I grew up using nitrocellulose lacquers and
enamels. Don't want to go back to them here in Oregon with all the moisture
in the air and wild temperature swings, but that being said, I was at an
indoor car show last weekend where a buddy of mine showed his 49 Merc lead
sled for the first time. About 40 coats of Candy Apple Red nitrocellulose
lacquer, wet sanded between every 5 coats. Nothing else even comes close to
that look. But the job cost 6 months wages, and took almost that long. I
don't have that much time left on my clock to invest in those paint jobs
any more. Still great to see old world craftsmanship though.
Jim Hupy
Salem, OR
78 GMC Royale 403
On Wed, Jan 18, 2012 at 11:58 AM, James Hupy <jamesh1296@gmail.com> wrote:
> Many of the commercial powder coaters in this area prefer to do the media
> blasting in house. They have several media that they use, from silicon
> carbide, aluminum oxide, glass beads, walnut shells, soda, etc. The powder
> coating should be applied as soon as possible after media blasting and
> metal prepping. That way they know that some grease monkey has not been
> handling the parts with stuff on their hands that prevents good adhesion. I
> personally have a powder coating outfit that I use for parts that are small
> enough to go in a 42" electric range oven. I have one in my shop that I use
> exclusively for that purpose. I also have a glass beading cabinet that uses
> compressed air to blast the surfaces of parts with glass beads to remove
> rust and scale. I use non residual chlorinated hydrocarbons to clean the
> parts before I powder coat them. On heavy castings like GMC knuckles that
> have been subjected to chassis grease, I first bake them in the oven for a
> couple of hours, then let them cool off before I final clean them and
> powder coat them. I have done quite a lot of it over the years, and have
> learned what does and what does not work. If it is not clean enough to eat
> off of, it is not clean enough to powder coat. Some lessons I have learned
> the hard way.
> Jim Hupy
> Salem, OR
> 78 GMC Royale 403
> On Wed, Jan 18, 2012 at 11:42 AM, <sgltrac@gmail.com> wrote:
>
>> Most of the powder coated parts for my rear suspension ended up that way
>> due to the cost of sand blasting. The cost to blast the parts was 60
>> percent or so of the total cost to blast and powder coat. Originally I was
>> planning to have bogie parts blasted then top coat with automotive paint
>> but it just diddnt make sense (to me anyway) to not have the whole thing
>> done since the powder cost was same or less than my material+labor costs.
>>
>> Sully
>> 77 royale
>> Sent from my Verizon Wireless BlackBerry
>>
>> -----Original Message-----
>> From: Matt Colie <matt7323tze@gmail.com>
>> Sender: gmclist-bounces@temp.gmcnet.org
>> Date: Wed, 18 Jan 2012 13:33:20
>> To: <gmclist@temp.gmcnet.org>
>> Reply-To: gmclist@temp.gmcnet.org
>> Subject: Re: [GMCnet] powder coating
>>
>>
>>
>> rssbob wrote on Wed, 18 January 2012 11:18
>> > The wheels on my recently acquired Palm Beach were disgusting looking
>> so I had them sand blasted and powder coated. I love the result but when I
>> installed the first hub cap I could see they were going to chip and scratch
>> the powder coated finish so I decided to go with the "non-hub-cap" look.
>> Now I am going to clean and paint everything inside the wheel wells black,
>> including my lug nuts. I also powder coated my old hub covers with a
>> matching green which I think will really set it off. I will post some
>> pictures when I get one side done. That also frees up a bunch of hub caps
>> in case anyone needs any. I have about 10 of them in various conditions.
>> >
>> > Bob Sobrito
>>
>> I now of a collection of mostly ugly 16" wheels, I went around locally
>> for quotes to sand blast and powder coat 7 and it was close to what JimK
>> would charge for hub centered alloy. I'm still planning to sand blast at a
>> really inexpensive shop and squirt so primer on them myself. I would have
>> liked the powder coat.
>>
>> Matt
>> --
>> Matt & Mary Colie
>> '73 Glacier 23 Chaumière (say show-me-air) Just about as stock as you
>> will find
>> SE Michigan - Twixt A2 and Detroit
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>>
>
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
Re: [GMCnet] powder coating [message #157210 is a reply to message #157193] |
Wed, 18 January 2012 14:50 |
emerystora
Messages: 4442 Registered: January 2004
Karma: 13
|
Senior Member |
|
|
On Jan 18, 2012, at 12:50 PM, Keith V wrote:
>
>
> I am so not a fan of powder coating.
> I firmly believe the industry has the public snowed.
> It has a sexy new(ish) name that sounds so cool and hi tech, it must be better right??
New(ish)??
Powder coating has been around since the late 1940's.
>
> The only real advantage of powder coating is that it's cleaner, no solvents and the over spray sweeps up.
>
> Durability wise a good polyurethane paint is far superior.
Durability really depends on what material is being powder coating
Between 1958 and 1965, literally all powder coatings, generally only functional applications with a film thickness of 150 µm to 500 µm, were processed by means of fluidized-bed application. Electric insulation, corrosion and abrasion resistance were in the foreground. The coating materials in those days were comprised of nylon 11, CAB, polyethylene, plasticized PVC, polyester and chlorinated polyether, among others, and at the same time, thermosetting epoxides, e.g. for dishwasher baskets (PVC), for heat insulation (epoxide), for boat accessories (nylon) and metal furniture (PVC, CAB). It was the Bosch company that developed the basic type of epoxy resin powder in their search for a suitable electric insulation material.
> They are both tough and temperature resistant, but urethane Is more flexible, has a chemical bond to the substrate rather than a mechanical bond, it's repairable, better UV protection, and it looks better. It's also low temperature, no need to bake the snot out of your part (like 450 degrees)
I cannot understand how polyurethane could have a chemical bond to metal. I think that if you explore the subject you will find that it is also a mechanical bond.
I agree that there are a lot of applications when polyurethane would be simpler and better.
But an epoxy powder coating is a great coating for a lot of applications.
Emery Stora
77 Kingsley
Santa Fe, NM
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
Re: [GMCnet] powder coating [message #157222 is a reply to message #157193] |
Wed, 18 January 2012 17:33 |
rssbob
Messages: 259 Registered: January 2004 Location: La Mesa, Ca. (San Diego a...
Karma: 0
|
Senior Member |
|
|
Keith,
I fell in love with powder coating when I had the wheels of my 47 Canadian Ford Monarch convertible done in a maize yellow to match the paint on the car. I owned the car for about 10 years and never had one problem with the coating. I also had a 46 Ford Commercial (1/2 ton) pick-up. Did all those wheels black, no problems. Then we had a patio set, 6 chairs and a table made of wrought iron. About every other year I would clean them up, get some rustoleum primer and paint and repaint them. Finally paid about 600 to get them powder coated a bright green to match our pergola and they have looked fantastic ever since. They sit outside all year long and still have that pristine green look.
So My experiences have been positive.
On Jan 18, 2012, at 11:50 AM, Keith V wrote:
>
>
> I am so not a fan of powder coating.
> I firmly believe the industry has the public snowed.
> It has a sexy new(ish) name that sounds so cool and hi tech, it must be better right??
>
> The only real advantage of powder coating is that it's cleaner, no solvents and the over spray sweeps up.
>
> Durability wise a good polyurethane paint is far superior.
> They are both tough and temperature resistant, but urethane Is more flexible, has a chemical bond to the substrate rather than a mechanical bond, it's repairable, better UV protection, and it looks better. It's also low temperature, no need to bake the snot out of your part (like 450 degrees)
>
> And its repairable, just spray some more on top....lets see you fix powder coating...
>
> I own my own powder coater and do use it.
> But 2 part urethane is better.
>
> Did I mention paint is repairable??
>
> --
> Keith
> 69 Vette
> 29 Dodge
> 75 Royale GMC
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Bob Sobrito
78 Palm Beach
La Mesa, Ca
|
|
|
Re: [GMCnet] powder coating [message #157224 is a reply to message #157222] |
Wed, 18 January 2012 17:42 |
Dolph Santorine
Messages: 1236 Registered: April 2011 Location: Wheeling, WV
Karma: -41
|
Senior Member |
|
|
We did hundreds of thousand of paging horns in powder coat back in the day, and it was environmentally friendly, looked great.
Now when I see these quarter century old parts, they STILL look great, and you know the materials (and the color choices) are better than ever before.
I don't know if the same thing can be said for the new water soluble automotive finished.
Dolph
On Jan 18, 2012, at 6:33 PM, robert sobrito wrote:
> Keith,
>
> I fell in love with powder coating when I had the wheels of my 47 Canadian Ford Monarch convertible done in a maize yellow to match the paint on the car. I owned the car for about 10 years and never had one problem with the coating. I also had a 46 Ford Commercial (1/2 ton) pick-up. Did all those wheels black, no problems. Then we had a patio set, 6 chairs and a table made of wrought iron. About every other year I would clean them up, get some rustoleum primer and paint and repaint them. Finally paid about 600 to get them powder coated a bright green to match our pergola and they have looked fantastic ever since. They sit outside all year long and still have that pristine green look.
>
> So My experiences have been positive.
>
> On Jan 18, 2012, at 11:50 AM, Keith V wrote:
>
>>
>>
>> I am so not a fan of powder coating.
>> I firmly believe the industry has the public snowed.
>> It has a sexy new(ish) name that sounds so cool and hi tech, it must be better right??
>>
>> The only real advantage of powder coating is that it's cleaner, no solvents and the over spray sweeps up.
>>
>> Durability wise a good polyurethane paint is far superior.
>> They are both tough and temperature resistant, but urethane Is more flexible, has a chemical bond to the substrate rather than a mechanical bond, it's repairable, better UV protection, and it looks better. It's also low temperature, no need to bake the snot out of your part (like 450 degrees)
>>
>> And its repairable, just spray some more on top....lets see you fix powder coating...
>>
>> I own my own powder coater and do use it.
>> But 2 part urethane is better.
>>
>> Did I mention paint is repairable??
>>
>> --
>> Keith
>> 69 Vette
>> 29 Dodge
>> 75 Royale GMC
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|
Re: [GMCnet] powder coating [message #157229 is a reply to message #157196] |
Wed, 18 January 2012 18:23 |
jhbridges
Messages: 8412 Registered: May 2011 Location: Braselton ga
Karma: -74
|
Senior Member |
|
|
Samesame for thick film piants (Imron, AlumiGrip, etc.)
--johnny
'76 23' trandmose norris
'76 palm beach
________________________________
From: James Hupy <jamesh1296@gmail.com>
To: gmclist@temp.gmcnet.org
Sent: Wednesday, January 18, 2012 2:58 PM
Subject: Re: [GMCnet] powder coating
If it is not clean enough to eat
off of, it is not clean enough to powder coat. Some lessons I have learned
the hard way.
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Foolish Carriage, 76 26' Eleganza(?) with beaucoup mods and add - ons.
Braselton, Ga.
I forgive them all, save those who hurt the dogs. They must answer to me in hell
|
|
|
Re: [GMCnet] powder coating [message #157231 is a reply to message #157210] |
Wed, 18 January 2012 18:33 |
jhbridges
Messages: 8412 Registered: May 2011 Location: Braselton ga
Karma: -74
|
Senior Member |
|
|
I cannot understand how polyurethane could have a chemical bond to metal. I think that if you explore the subject you will find that it is also a mechanical bond.
I agree that there are a lot of applications when polyurethane would be simpler and better.
But an epoxy powder coating is a great coating for a lot of applications.
Emery Stora
77 Kingsley
Santa Fe, NM
Well, interestingly enough, AlumiGrip <tm> wouldn't stick to aluminum at all. We had to spray the plane with a wash primer first, to which it bonds like all the proverbial things.
--johnny
'76 23' transmode norris
'76 palm beach
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Foolish Carriage, 76 26' Eleganza(?) with beaucoup mods and add - ons.
Braselton, Ga.
I forgive them all, save those who hurt the dogs. They must answer to me in hell
|
|
|
Goto Forum:
Current Time: Wed Oct 09 17:16:27 CDT 2024
Total time taken to generate the page: 0.01293 seconds
|