GMCforum
For enthusiast of the Classic GMC Motorhome built from 1973 to 1978. A web-based mirror of the GMCnet mailing list.

Home » Public Forums » GMCnet » Re: [GMCnet] help, FURTHER ISSUE WITH PS - drive belt has broken in Manhattan!
Re: [GMCnet] help, FURTHER ISSUE WITH PS - drive belt has broken in Manhattan! [message #152533] Sun, 11 December 2011 13:00 Go to previous message
JP Winger is currently offline  JP Winger   United States
Messages: 86
Registered: September 2011
Karma:
Member
Yes thanks Dan, I just called Matt and he did!
I've never tightened a belt before, I have a metal bar to wide to get in the gap where the shaft is so I tried to prize it against the water pump sheeth but couldn't budge it. Does the PS move straight across horizontal or diagonally?
Any tips to freeing it up?
Thanks

John-Paul Winger / US+1 310 9231126 / NZ+64 21 997919 / lavidalocations@gmail.com / Skype: lavidalocations

On Dec 11, 2011, at 1:42 PM, "Dan Winchester" <gmcnet@dwinchester.com> wrote:

> I may have missed it but has anyone warned you not to port on the sheet metal reservoir on the power steering pump.
>
> Dan Winchester
> www.dwinchester.com
>
> ----- Reply message -----
> From: "JP Winger" <lavidalocations@gmail.com>
> Date: Sun, Dec 11, 2011 8:04 am
> Subject: [GMCnet] help, FURTHER ISSUE WITH PS - drive belt has broken in Manhattan!
> To: "gmclist@temp.gmcnet.org" <gmclist@temp.gmcnet.org>
>
> The belt has almost an inch of play - guess that must be a little too much?
> I can see a single nut there in the gap between the wheel? And the power steering frame, do you loosen that with a wrench (or take it off?) and somehow pry it tighter?
>
> John-Paul Winger / US+1 310 9231126 / NZ+64 21 997919 / lavidalocations@gmail.com / Skype: lavidalocations
>
> On Dec 11, 2011, at 12:51 PM, JP Winger <lavidalocations@gmail.com> wrote:
>
> > Thanks Tim and nice talking to you, much appreciated.
> >
> > I'll try call a couple of you for advice but I'm trying to drive away but now when I turn the wheel the PS belt squeals and shudders a bit to get the wheels turned hard (this is Manhattan - I'm parked in by a range rover and a BMW - abt 6 inches either side so it'll require a 50 pt turn to get out). Squealing and starting to smell a little but from what I can see it's just the belt slipping and the alt belt must have been helping it out! Hopefully it won't damage it for me to use for 10 miles?
> >
> > I'll try again and it may be lots better once not in such a fix but any advise welcome.
> >
> > Regards,
> > JP
> >
> >
> >
> > John-Paul Winger / US+1 310 9231126 / NZ+64 21 997919 / lavidalocations@gmail.com / Skype: lavidalocations
> >
> > On Dec 11, 2011, at 10:47 AM, Tim Conway <mactac735@mac.com> wrote:
> >
> >> On Dec 11, 2011, at 10:36 AM, JP Winger wrote:
> >>
> >>> John-Paul Winger / US+1 310 9231126
> >>
> >>
> >> Hi JP,
> >>
> >> I just tried the above phone number and got the message -not reachable-. I've been calling some stores and located one that says they have all three belts. Pep Boys in Long Island City, just the other side of the East River.
> >>
> >> Try me on my cell phone six 3 one 6 seven 8 six 1 6 ate.
> >>
> >> If you need me to, I'll go get them and bring them to you. If I don't hear from you, I'll post the address here for you.
> >>
> >> Best wishes, Tim
> >>
> >> Tim Conway
> >> LI NY 78 PB
> >> _______________________________________________
> >> GMCnet mailing list
> >> Unsubscribe or Change List Options:
> >> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
>
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist

 
Read Message
Read Message
Read Message
Read Message
Read Message
Previous Topic: Re: [GMCnet] quiet GMC
Next Topic: [GMCnet] Fridge Unit
Goto Forum:
  


Current Time: Sun Sep 22 18:27:09 CDT 2024

Total time taken to generate the page: 0.00811 seconds