|
Re: [GMCnet] Parked,until replaced-upper control arm [message #143393 is a reply to message #143330] |
Wed, 14 September 2011 18:39 |
|
USAussie
Messages: 15912 Registered: July 2007 Location: Sydney, Australia
Karma: 6
|
Senior Member |
|
|
TJ,
Try:
Bob Stone in Carbondale, IL: (618)-964-9124
Followed by the usual suspects:
Applied GMC in Fremont, CA: (510) 440-1101
Michael Bozardt in Houston: TX: (713) 373-7775
Jim Bounds in Orlando, FL: (407) 857-5777
Jeff Sirum in Okeechobee, FL: (863)-763-1121
Regards,
Rob M.
-----Original Message-----
From: PalmBeachGMCSTL@aol.com
Need upper control arm driver's side. Yes, there is a story, but another
day in the life of our GMC's. Thanks in advance.
TJ
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Regards,
Rob M. (USAussie)
The Pedantic Mechanic
Sydney, Australia
'75 Avion - AUS - The Blue Streak TZE365V100428
'75 Avion - USA - Double Trouble TZE365V100426
|
|
|
Re: [GMCnet] Parked,until replaced-upper control arm [message #143397 is a reply to message #143393] |
Wed, 14 September 2011 19:05 |
|
WD0AFQ
Messages: 7111 Registered: November 2004 Location: Dexter, Mo.
Karma: 207
|
Senior Member |
|
|
Robert Mueller wrote on Wed, 14 September 2011 18:39 | TJ,
Try:
Bob Stone in Carbondale, IL: (618)-964-9124
Followed by the usual suspects:
Applied GMC in Fremont, CA: (510) 440-1101
Michael Bozardt in Houston: TX: (713) 373-7775
Jim Bounds in Orlando, FL: (407) 857-5777
Jeff Sirum in Okeechobee, FL: (863)-763-1121
Regards,
Rob M.
-----Original Message-----
From: PalmBeachGMCSTL@aol.com
Need upper control arm driver's side. Yes, there is a story, but another
day in the life of our GMC's. Thanks in advance.
TJ
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
Rob, TJ is very familiar with Mr. Stone.
Email me when you have time, TJ, and tell me how u did that. A used upper should not be hard to find.
Dan
3 In Stainless Exhaust Headers
One Ton All Discs/Reaction Arm
355 FD/Quad Bag/Alum Radiator Manny Tran/New eng.
Holley EFI/10 Tire Air Monitoring System
Solarized Coach/Upgraded Windows
Satelite TV/On Demand Hot Water/3Way Refer
|
|
|
Re: [GMCnet] Parked,until replaced-upper control arm [message #143402 is a reply to message #143397] |
Wed, 14 September 2011 19:19 |
|
USAussie
Messages: 15912 Registered: July 2007 Location: Sydney, Australia
Karma: 6
|
Senior Member |
|
|
Dan,
I can tell you one way to wind up with a "failed" upper control arm that Chuck Boyd knows about. Someone changed the upper control
arms on Double Trouble and DID NOT put a "half moon" between the parts that the bushing goes through which deformed them. The first
visit I made to Chucks house I mentioned that the steering was vague. TWO SECONDS later he was crawling around trying to find out
why. When he got to the drivers side he called me over and showed me that he could move the upper control arm in and out / back and
forth because the bushing was loose in the a-frame. When I installed new bushings at the COOP Jason straightened up the deformed
part around the bushings and tack welded the new bushing in place to prevent it from moving. He'd make a weld about 1/4" long and
I'd douse the weld with water to keep from frying the bushing. It worked fine.
Regards,
Rob M.
-----Original Message-----
From: Dan Gregg
Rob, TJ is very familiar with Mr. Stone.
Email me when you have time, TJ, and tell me how u did that. A used upper should not be hard to find.
Dan
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Regards,
Rob M. (USAussie)
The Pedantic Mechanic
Sydney, Australia
'75 Avion - AUS - The Blue Streak TZE365V100428
'75 Avion - USA - Double Trouble TZE365V100426
|
|
|
|
Re: [GMCnet] Parked,until replaced-upper control arm [message #143464 is a reply to message #143330] |
Thu, 15 September 2011 06:50 |
Steven Ferguson
Messages: 3447 Registered: May 2006
Karma: 0
|
Senior Member |
|
|
TJ,
Any upper from a '68 or older Eldo, Toro, will work. '78 is the last year
of compatibility.
On Wed, Sep 14, 2011 at 10:01 AM, <PalmBeachGMCSTL@aol.com> wrote:
> Need upper control arm driver's side. Yes, there is a story, but another
> day in the life of our GMC's. Thanks in advance.
>
> TJ Rinn
> 77 45 PB
> St. Louis, Mo
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
--
Steve Ferguson
Sierra Vista, AZ
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
|
|
|