Home » Public Forums » GMCnet » Wallace front wheel bearing seals?
| Wallace front wheel bearing seals? [message #102448] |
Sun, 10 October 2010 20:08  |
GMCNUSA
Messages: 283
Registered: August 2006
Location: Indianapolis, IN
Karma: 0
|
Senior Member |
|
|
I have wallace hubs on my coach and a cv boot ripped and when I pulled the axel the seal in the hub is torn. I don't have any part #s and have not pulled the seal out of hub. Does anyone have any info?
Thanks,
Larry Dilk
Indianapolis, IN
76 Eleganza II
Patterson 455,Turbo City TBI,
Just LOVE It!
|
|
|
|
|
|
| Re: Wallace front wheel bearing seals? [message #102456 is a reply to message #102451] |
Sun, 10 October 2010 20:34  |
GMCNUSA
Messages: 283
Registered: August 2006
Location: Indianapolis, IN
Karma: 0
|
Senior Member |
|
|
| WD0AFQ wrote on Sun, 10 October 2010 21:14 |
Larry, I am sure you have looked real hard for any id on the seal. If nothing, I would take to NAPA and try to find one to match. I am sure someone here knows what you need.
Does it resemble the stock seal at all?
Dan
|
To be truthful I just crawled out from under coach after I got the axel out in the dark. I did not pull the seal so it might have a number. I was discouraged because I decided to do some front end rebuild maybe new offset A arms, ball joints, etc. and when I took upper ball joint loose the knuckle dropped and pulled on the axel and the inner 3 ball joint came apart dropping little needle bearings and 2 balls on the driveway. SO I quit before I broke anything else. Shouldn't do things when tired, its dark and in a hurry. I wanted to ask the forum incase I can't find a number.
Larry Dilk
Indianapolis, IN
76 Eleganza II
Patterson 455,Turbo City TBI,
Just LOVE It!
|
|
|
|
|
|
| Re: [GMCnet] Wallace front wheel bearing seals? [message #102463 is a reply to message #102456] |
Sun, 10 October 2010 20:51 |
Ken Henderson
Messages: 8726
Registered: March 2004
Location: Americus, GA
Karma: 9
|
Senior Member |
|
|
Larry,
Without knowing any details of the Wallace hubs, I suspect you may have
better luck at Bearings and Drives or another large industrial bearing
supply house than at NAPA.
Ken H.
On Sun, Oct 10, 2010 at 9:34 PM, Larry and Cheryl Dilk <lwd222@msn.com>wrote:
>
>
> WD0AFQ wrote on Sun, 10 October 2010 21:14
> > Larry, I am sure you have looked real hard for any id on the seal. If
> nothing, I would take to NAPA and try to find one to match. I am sure
> someone here knows what you need.
> > Does it resemble the stock seal at all?
> > Dan
>
> To be truthful I just crawled out from under coach after I got the axel out
> in the dark. I did not pull the seal so it might have a number. I was
> discouraged because I decided to do some front end rebuild maybe new offset
> A arms, ball joints, etc. and when I took upper ball joint loose the knuckle
> dropped and pulled on the axel and the inner 3 ball joint came apart
> dropping little needle bearings and 2 balls on the driveway. SO I quit
> before I broke anything else. Shouldn't do things when tired, its dark and
> in a hurry. I wanted to ask the forum incase I can't find a number.
> --
> Larry Dilk
> Indianapolis, IN
> 76 Eleganza II
> Patterson 455,Turbo City TBI,
> Just LOVE It!
> _______________________________________________
> GMCnet mailing list
> List Information and Subscription Options:
> http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
>
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Ken Henderson
Americus, GA
www.gmcwipersetc.com
Large Wiring Diagrams
76 X-Birchaven
76 X-Palm Beach
|
|
|
|
| Re: [GMCnet] Wallace front wheel bearing seals? [message #102489 is a reply to message #102456] |
Sun, 10 October 2010 23:11 |
 |
USAussie
Messages: 15912
Registered: July 2007
Location: Sydney, Australia
Karma: 6
|
Senior Member |
|
|
Larry,
In case you're wondering the inner CV joint has 50 needles in each one of
the balls.
Guess how I know! ;-)
Regards,
Rob M.
USAussie
-----Original Message-----
From: gmclist-bounces@temp.gmcnet.org
[mailto:gmclist-bounces@temp.gmcnet.org] On Behalf Of Larry and Cheryl Dilk
Sent: Sunday, October 10, 2010 8:34 PM
To: gmclist@temp.gmcnet.org
Subject: Re: [GMCnet] Wallace front wheel bearing seals?
WD0AFQ wrote on Sun, 10 October 2010 21:14
> Larry, I am sure you have looked real hard for any id on the seal. If
nothing, I would take to NAPA and try to find one to match. I am sure
someone here knows what you need.
> Does it resemble the stock seal at all?
> Dan
To be truthful I just crawled out from under coach after I got the axel out
in the dark. I did not pull the seal so it might have a number. I was
discouraged because I decided to do some front end rebuild maybe new offset
A arms, ball joints, etc. and when I took upper ball joint loose the knuckle
dropped and pulled on the axel and the inner 3 ball joint came apart
dropping little needle bearings and 2 balls on the driveway. SO I quit
before I broke anything else. Shouldn't do things when tired, its dark and
in a hurry. I wanted to ask the forum incase I can't find a number.
--
Larry Dilk
Indianapolis, IN
76 Eleganza II
Patterson 455,Turbo City TBI,
Just LOVE It!
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Regards,
Rob M. (USAussie)
The Pedantic Mechanic
Sydney, Australia
'75 Avion - AUS - The Blue Streak TZE365V100428
'75 Avion - USA - Double Trouble TZE365V100426
|
|
|
|
|
|
| Re: [GMCnet] Wallace front wheel bearing seals? [message #102516 is a reply to message #102489] |
Mon, 11 October 2010 07:16 |
Ken Henderson
Messages: 8726
Registered: March 2004
Location: Americus, GA
Karma: 9
|
Senior Member |
|
|
Rob,
I REALLY hate to be the one to break this news to you, but you need to know:
You're missing some needles. :-(
Page 3B10 of manual X7575 is very specific in two places about there being
53 (FIFTY-THREE) needles in each of the inner CV balls. 50 just didn't
match my faint memory so I checked.
Hope that doesn't cause you too much sleep loss before you get them out to
inspect.
Ken H.
On Mon, Oct 11, 2010 at 12:11 AM, Rob Mueller <robmueller@iinet.net.au>wrote:
> Larry,
>
> In case you're wondering the inner CV joint has 50 needles in each one of
> the balls.
>
> Guess how I know! ;-)
>
> Regards,
> Rob M.
> USAussie
>
>
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Ken Henderson
Americus, GA
www.gmcwipersetc.com
Large Wiring Diagrams
76 X-Birchaven
76 X-Palm Beach
|
|
|
|
| Re: Wallace front wheel bearing seals? [message #102519 is a reply to message #102448] |
Mon, 11 October 2010 07:45 |
fred v
Messages: 999
Registered: April 2006
Location: pensacola, fl.
Karma: 0
|
Senior Member |
|
|
| GMCNUSA wrote on Sun, 10 October 2010 20:08 |
I have wallace hubs on my coach and a cv boot ripped and when I pulled the axel the seal in the hub is torn. I don't have any part #s and have not pulled the seal out of hub. Does anyone have any info?
Thanks,
|
it's just a guess but since the seal is running on the same cv joint as the OEM hub i would think it uses the same seal.
Fred V
'77 Royale RB 455
P'cola, Fl
|
|
|
|
| Re: [GMCnet] Wallace front wheel bearing seals? [message #102545 is a reply to message #102516] |
Mon, 11 October 2010 10:50 |
|
USAussie
Messages: 15912
Registered: July 2007
Location: Sydney, Australia
Karma: 6
|
Senior Member |
|
|
Ken,
Thanks for correcting me, I was going to double check the number in the
parts manual but I was SURE it was 50!
I am sure that when I re-greased the inner CV they were all there because I
remember what a PITA it was to get the last couple in.
I will admit that this message clearly demonstrates I am missing a few
marbles, however! ;-)
Regards,
Rob M.
USAussie
-----Original Message-----
From: gmclist-bounces@temp.gmcnet.org
[mailto:gmclist-bounces@temp.gmcnet.org] On Behalf Of Ken Henderson
Sent: Monday, October 11, 2010 7:17 AM
To: gmclist@temp.gmcnet.org
Subject: Re: [GMCnet] Wallace front wheel bearing seals?
Rob,
I REALLY hate to be the one to break this news to you, but you need to know:
You're missing some needles. :-(
Page 3B10 of manual X7575 is very specific in two places about there being
53 (FIFTY-THREE) needles in each of the inner CV balls. 50 just didn't
match my faint memory so I checked.
Hope that doesn't cause you too much sleep loss before you get them out to
inspect.
Ken H.
_______________________________________________
GMCnet mailing list
List Information and Subscription Options:
http://temp.gmcnet.org/cgi-bin/mailman/listinfo/gmclist
Regards,
Rob M. (USAussie)
The Pedantic Mechanic
Sydney, Australia
'75 Avion - AUS - The Blue Streak TZE365V100428
'75 Avion - USA - Double Trouble TZE365V100426
|
|
|
|
|
|
|
|
| Re: [GMCnet] Wallace front wheel bearing seals? [message #102743 is a reply to message #102709] |
Tue, 12 October 2010 20:04 |
GMCNUSA
Messages: 283
Registered: August 2006
Location: Indianapolis, IN
Karma: 0
|
Senior Member |
|
|
| jade wrote on Tue, 12 October 2010 16:25 |
Larry;
I have had Wallace hubs for 20 years and have replaced the front seals a few
times.
They are the same as the original seals.
JADE
72 23' ?/ 73 26' Painted Desert
Ajo, AZ
KC7QGC--
----- Original Message -----
From: "Larry and Cheryl Dilk" <lwd222@msn.com>
To: <gmclist@temp.gmcnet.org>
Sent: Sunday, October 10, 2010 6:08 PM
Subject: [GMCnet] Wallace front wheel bearing seals?
>
>
_______________________________________________
|
Thanks Jade I have come to that revelation after more searching.
Larry Dilk
Indianapolis, IN
76 Eleganza II
Patterson 455,Turbo City TBI,
Just LOVE It!
|
|
|
|
Goto Forum:
Current Time: Sun Nov 17 12:39:23 CST 2024
Total time taken to generate the page: 0.01441 seconds
|
GMCforum
Search
Help
Register
Login
Home
