GMCforum: GMCnet » Engine Removal

Home » Public Forums » GMCnet » Engine Removal

Show: Today's Messages :: Polls :: Message Navigator

Re: [GMCnet] Engine Removal [message #328509 is a reply to message #328507]

Mon, 22 January 2018 16:45

James Hupy

Messages: 6806
Registered: May 2010

Karma:

Senior Member

No. But, there are about 6 bell housing bolts, 5 final drive bolts, (3 on
one side, 2 on the other) 2 front motor mount bolts, and 3 torque converter
bolts, and 3 oil filter adapter bolts. 2 radiator hoses, 2 or 3 heater
hoses. 8 water pump bolts, 10 exhaust manifold bolts, various vacuum hoses,
fuel lines, sender wires, alternator wires, carb linkages, 1 distributor
hold down, 4 carb bolts. That just about does it.

On Jan 22, 2018 1:48 PM, "Johnny Bridges via Gmclist" <
gmclist@list.gmcnet.org> wrote:

> Can you get the engine out the top without removing the trans/final drive?
>
> johnny
>
> --
> 76 26' Eleganza(?) with beaucoup mods and add - ons.
> Braselton, Ga.
> "I forgive them all, save those who hurt the dogs. They must answer to me
> in hell" - ol Andy, paraphrased
>
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org

Report message to a moderator

[Message index]

		Engine Removal By: Carl S. on Sun, 21 January 2018 14:29
		Re: [GMCnet] Engine Removal By: <tawptool on Sun, 21 January 2018 14:45
		Re: [GMCnet] Engine Removal By: sgltrac on Sun, 21 January 2018 14:53
		Re: [GMCnet] Engine Removal By: tphipps on Sun, 21 January 2018 15:41
		Re: [GMCnet] Engine Removal By: Rollerg on Sun, 21 January 2018 19:32
		Re: [GMCnet] Engine Removal By: sgltrac on Sun, 21 January 2018 20:14
		Re: [GMCnet] Engine Removal By: Ken Burton on Sun, 21 January 2018 20:31
		Re: Engine Removal By: Jim Wagner on Sun, 21 January 2018 16:00
		Re: Engine Removal By: lqqkatjon on Sun, 21 January 2018 16:33
		Re: Engine Removal By: Scott Nutter on Sun, 21 January 2018 17:18
		Re: Engine Removal By: Ken Burton on Sun, 21 January 2018 18:59
		Re: Engine Removal By: Larry on Sun, 21 January 2018 20:42
		Re: [GMCnet] Engine Removal By: Sandra Price on Mon, 22 January 2018 00:06
		Re: Engine Removal By: Carl S. on Mon, 22 January 2018 11:08
		Re: [GMCnet] Engine Removal By: Richard Denney on Mon, 22 January 2018 18:30
		Re: [GMCnet] Engine Removal By: Kosier on Mon, 22 January 2018 19:13
		Re: [GMCnet] Engine Removal By: Ken Henderson on Mon, 22 January 2018 19:39
		Re: [GMCnet] Engine Removal By: Carl S. on Mon, 22 January 2018 19:55
		Re: Engine Removal By: Adrien G. on Mon, 22 January 2018 00:21
		Re: Engine Removal By: Larry on Mon, 22 January 2018 12:40
		Re: [GMCnet] Engine Removal By: James Hupy on Mon, 22 January 2018 12:56
		Re: Engine Removal By: Scott Nutter on Mon, 22 January 2018 10:18
		Re: Engine Removal By: Larry on Mon, 22 January 2018 12:35
		Re: Engine Removal By: jhbridges on Mon, 22 January 2018 15:47
		Re: [GMCnet] Engine Removal By: James Hupy on Mon, 22 January 2018 16:45
		Re: Engine Removal By: dservati1 on Mon, 29 January 2018 23:53
		Re: Engine Removal By: dservati1 on Tue, 30 January 2018 00:22

Previous Topic:	[GMCnet] LP gas line in the right rear wheel well. Has that been a problem?
Next Topic:	OFF TOPIC- NOT GMC - Long read

Goto Forum:

-=] Back to Top [=-

Current Time: Mon May 13 10:14:46 CDT 2024

Total time taken to generate the page: 0.02027 seconds